Gebruiksaanwijzing /service van het product TXB-V van de fabrikant Pelco
Ga naar pagina of 32
INST ALLA TION/OPERA TION TXB-V T ranslator Board C656M-E (4/07).
2 C656M-E (04/07) Contents Important Safety Instructi ons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Important Notice. . . . . . . . . . . . . . . . . . . . . . . . . . .
C656M-E (4/07) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Only use attachments/accessories specified by the manufacturer . 6. Installation should be don e only by qualified personnel and conform to all local codes.
4 C656M-E (4/07) Regulatory Notices This device complies with Part 15 of the FCC Rules. O peration is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
C656M-E (4/07) 5 Description The TXB-V translator board allows Vicon ® controllers to communicate with Pelco’ s ExSite ™ , Esprit ® , and Spectra ® systems. After setup, the controller functions the same as a V icon controller normally would, except as noted in the Operation section on page 21.
6 C656M-E (4/07) Esprit Installation T o install the TXB-V translator board in an Esprit system (refer to Figure 1): 1. T urn off power to the Esprit system. 2. Remove the left cover fro m the pan and tilt. 3. Remove the short ing plug from the 16-pin c onnector on the E sprit system’ s circuit board.
C656M-E (4/07) 7 Figure 2. TXB-V T ermination and B aud Rate (Bottom View) 6. Set the baud rate for the TXB-V translator board (from the controller). Use the P3 and P4 jumpers (refer to the following tab le). 7. Install the TXB-V on the Esprit circuit board (refer to Figure 3): a.
8 C656M-E (4/07) 9. Reinstall the left cover of the pan and tilt: a. Properly position the cover and slide it into place. The sides of the cover must fit under the front and back rain guards of the pan and tilt. The top of the cover must seat against the lip of the top gasket.
C656M-E (4/07) 9 Figure 5. Fastening the Es prit Cover 10. Remove the pan and tilt from the base of the Esprit system. 11. Check the control wiring inside the base of the unit. Refer to the Esprit documentation and the documentation supplied with your controller to make su re the wiring is correct.
10 C656M-E (4/07) Spectra III/Spectra IV Installation T o install the TXB-V translator board in a Spectra III/Spectra IV Series: 1. T urn off power to the dome system. 2. Remove the lower dome. 3. Remove the do me drive by pressing in the blue and red tabs on the sides of the dome drive.
C656M-E (4/07) 11 6. Install the TXB-V translator board into the back box: a. Open the hinged door to the back box. Push the tab lock towards the back box wall of the unit and open the door (refer to Figure 7). Figure 7. Spectra III/Spectra IV Back Box Interconnect Door b.
12 C656M-E (4/07) c. Remove the shorting plug from th e 16-pin connector located on the back box circuit bo ard (refer to Figure 8). Figure 8. Spectra III/Spectra IV Back Box Circuit Board NOTES: • Discard the 4-40 screw and its lock washer; they are not used in the Spectra III/Spectra IV system.
C656M-E (4/07) 13 b. For Spectra III systems, set al l SW3 switches on the dome to the OFF position. For Spectra IV systems, set SW2-1 through SW2-8 to the OFF position. 8. Install the dome drive (refer to Figure 11). Line up the blue (A) and red (B) tabs with the blu e (A) and red (B) labels.
14 C656M-E (4/07) Spectra Mini Dome Installation T o install the T XB-V translator board in a Spectra Mini dome: NOTE: Installing a TXB-V into a mini dome increases unit heigh t. In surface mount installations, you must cut a hole in the surface to accommodate the TXB-V cover .
C656M-E (4/07) 15 5. Set the P2 jumper on the TXB-V to the pro per termination setting (refer to Figure 13). Note the following: • By default, the P2 jumper is installed in the unt erminated position. • All TXB-Vs in a daisy chain, except the last unit, must be un terminated.
16 C656M-E (4/07) Figure 14. Removing the Mini Dome Cover and Shor ting Plug c. Insert the TXB-V translator board into the 16-p in connector on the Spectra Mini dome’ s circuit board. d. Install the translator bo ard cover that is supplied with the Spectra Mini dome .
C656M-E (4/07) 17 8. Check the wiring to the controller . Refer to the Spectra Mini dome docume ntation and the documentation supplied with your controller to make su re the wiring is correct. 9. Refer to the installation manua l for the Spec tra Mini dome to complete the installation.
18 C656M-E (4/07) ExSite Installation T o install the TXB-V translator board in an ExSite unit: 1. T urn off the power to the ExSite system. 2. Remove the pan an d tilt unit from the power module (refer to Figure 16 and Figure 17): a. Loosen the setscrew in the lockin g ring with a 2 mm Alle n wrench.
C656M-E (4/07) 19 • T o unterminate a TXB-V , remove the P2 jumper from the TXB-V and place it over one pin for storage. NOTE: When combining Pelco and Vicon receivers in the same system, refer to the Vicon manual for proper RS-485 configuration o f the Vicon receiver(s).
20 C656M-E (4/07) Figure 19. Installing the TXB-V into the ExSite 6. Check the wiring to the controller . Refer to the ExSite documen tation and the d ocumentation supplied with your controller to make sure the wiring is correct. 7. Set the DIP switches on the ExSite system (refer to Figure 19 for switch location): a.
C656M-E (4/07) 21 Operation Set preset 94 to access the camera menus. Press Iris Open to select menu items. The following table shows how the Vicon keyboard relates to the Pelco translator . Refer to your Vicon documentation for operating instructions.
22 C656M-E (4/07) TXB-V ZONE PROGRAMMING PROCEDURE A zone is a pan area, defined by a left and right limit, on the 360-degree pan plane. T o program a zone using a Vicon controller (refer to the manua.
C656M-E (4/07) 23 T roubleshooting Symptom Possible Cause Su ggested Remedy No video is displayed. Power is not connected to the Pelco unit. Check the power connector . Video cable is not connected to the Pelco unit. Check the video connector . T ranslator board is not inserted properly .
24 C656M-E (4/07) Appendix Ta b l e A . Receiver Address Settings Receiver Address Switch Setting 12345678 1 ON OFF OFF OFF OFF OFF OFF OFF 2 OF F ON OFF OFF OFF OFF OF F OFF 3 ON ON OFF OFF OFF OFF O.
C656M-E (4/07) 25 38 OFF ON ON OFF OFF ON OFF OFF 39 ON ON ON OFF OFF ON OFF OFF 40 OFF OFF OFF ON OFF ON OFF OFF 41 ON OFF OFF ON OFF ON OFF OFF 42 OFF ON OFF ON OFF ON OFF OFF 43 ON ON OFF ON OFF ON.
26 C656M-E (4/07) 78 OFF ON ON ON OFF OFF ON OFF 79 ON ON ON ON OFF OFF ON OFF 80 OFF OFF OFF OFF ON OFF ON OFF 81 ON OFF OFF OFF ON OFF ON OFF 82 OFF ON OFF OFF ON OFF ON OFF 83 ON ON OFF OFF ON OFF .
C656M-E (4/07) 27 118 OFF ON ON OFF ON ON ON OFF 119 ON ON ON OFF ON ON ON OFF 120 OFF OFF OFF ON ON ON ON OFF 1 2 1 O N O F F O F F O NO NO NO N O F F 122 OFF ON OFF ON ON ON ON OFF 123 ON ON OFF ON .
28 C656M-E (4/07) 158 OFF ON ON ON ON OFF OFF ON 1 5 9 O NO NO NO NO N O F F O F F O N 160 OFF OFF OFF OFF OFF ON OFF ON 161 ON OFF OFF OFF OFF ON OFF ON 162 OFF ON OFF OFF OFF ON OFF ON 163 ON ON OFF.
C656M-E (4/07) 29 198 OFF ON ON OFF OFF OFF ON ON 199 ON ON ON OFF OFF OFF ON ON 200 OFF OFF OFF ON OFF OFF ON ON 2 0 1O NO F F O F FO NO F F O F FO N O N 202 OFF ON OFF ON OFF OFF ON ON 203 ON ON OFF.
30 C656M-E (4/07) 238 OFF ON ON ON OFF ON ON ON 239 ON ON ON ON OFF ON ON ON 240 OFF OFF OFF OFF ON ON ON ON 241 ON OFF OFF OFF ON ON ON ON 242 OFF ON OFF OFF ON ON ON ON 2 4 3 O NO N O F F O F F O NO.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any mer c handise proved defective in ma terial or wor kmanship for a period of one year after th e date of shipment.
Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
Een belangrijk punt na aankoop van elk apparaat Pelco TXB-V (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Pelco TXB-V heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Pelco TXB-V vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Pelco TXB-V leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Pelco TXB-V krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Pelco TXB-V bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Pelco TXB-V kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Pelco TXB-V . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
