Gebruiksaanwijzing /service van het product 9002 van de fabrikant AT&T
Ga naar pagina of 21
Part 2 Please r ead Part 1 — Important Product Infor mation, included in y our package. User's Manual for 9 0 0 M H z T w o-Line C o r dless Speak erphone 9 00 2 2 9002_cover.
© 1998 Philips Consumer Communications L.P . All rights reser ved. Printed in China. 848233896 Issue 1A T&T 9002_cover.1AT&T 8/12/98, 4:03 PM 1.
1 CONTENTS INST ALLA TION ................................. 3 T able/Desk Installation .......................... 3 W all Installation ..................................... 5 Belt Clip ................................................ 6 OPERA TION ....
2 9002_book.1AT&T 8/12/98, 4:09 PM 2.
3 Standard Electrical Outlet INST ALLA TION Telephone Jacks L1 L2 L1/L2 OR Telephone line cords Power cord Modular Telephone Jacks T able/Desk Installa tion 1 Choose a spot near an electrical outlet and a telephone jack. This phone requires a modular telephone jac k and a standard electrical outlet (110v A C).
4 4 Connect the telephone line cord(s) to the base. • If you have a two-line jack , use only the white line cord. Plug one end into the jack labeled L1/L2 on the back of the base. • If you have two separate jacks , use both the white and clear line cords.
5 W all Installation INST ALLA TION 1 Follow Steps 1–3 under T able/Desk Installation. 2 Tur n the base unit over , and attach the wall mounting base to the lower half of the base unit. Gently pr ess down until it snaps firmly into place. 3 Connect the power cord.
6 INST ALLA TION the e xcess line cord under the tab on the bottom of the telephone base. Plug the line cord into your other one-line wall jac k. Y ou will be connected to Line 2. 5 Mount the telephone on the wall jack. Position the telephone base so the mounting studs on the w all jac k fit into the base of the telephone.
7 OPERA TION Initiate a confer ence call Put a caller on hold Mute the microphone Adjust speaker volume Send a paging tone to handset/ intercom between base and handset Line 2 – Activate speakerphon.
8 OPERA TION Line 1 – Make or answer a call Line 2 – Make or answer a call Line 1 and Line 2 buttons flash if base or extension is in use Temporary tone Store and access numbers in telephone memor.
9 Making a Call 1 Press and release L or l , and wait f or a dial tone. The line button of the line you’ re using lights. 2 When you hear a dial tone, dial the number . Ans w ering a Call Press and release the f lashing L or l button on the handset or the base to answ er a call on that line.
10 Checking Handset Ringer Selection 1 Press p , * . 2 Press 1 f or Line 1 or 2 for Line 2. 3 Press * . Y ou will hear the current ringer style selection. 4 Press o to e xit. NOTE: If y ou’r e on a call on one line and a call comes in on the other line, y ou will hear an “alert” tone on your call.
11 Special T elephone Ser vices If you subscribe to special local telephone company services like Call W aiting or Call Forw arding, you can access them by pressing the line button of the line you’ re cur rentl y using whenever you would pr ess the s witchhook on a cor ded phone.
12 Confer ence Calls Y ou can use both lines at the same time to set up a three-wa y conference call from the handset. 1 Answ er or make a call on one line. 2 Press the other line button, and make or answ er another call (your first call is automatically put on hold).
13 Headset Jack Y ou can use this telephone hands-free when you install an optional headset and use the belt clip provided. 1 Attach the belt c lip (see “Belt Clip” in the INST ALLA TION section of this manual). 2 Plug the headset (purc hased separately) into the jac k located on the right side of the handset.
14 This cordless telephone operates at the maximum po wer allowed by the F ederal Communications Commission (FCC). Even so, this handset and base can communicate over onl y a cer tain distance — which can var y with the locations of the base and handset, the weather , and the constr uction of your home or office.
15 This cordless phone can store 10 telephone numbers that you can dial just by pressing p and a number button. Storing Memor y Numbers 1 Make sure the handset is off. 2 Press p . 3 Press a number button (0 to 9) to select a memory location. 4 Enter the number (up to 16 digits) you want to store — OR — Press R to store the last number dialed.
16 CAUTION: T o reduce the risk of fire or injur y to persons or damage to the telephone, read and follow these instructions carefull y . • Use only Replacement Batter y 3740. • Do not dispose of the batter y in a fire. The cell might explode. Check with local codes for special disposal instructions.
17 5 The new batter y pack must be c harged bef ore using this telephone. Place the handset in the base and allow it to c harge f or 16 hours. Y our telephone might operate bef ore that, but f or best performance, let the handset batter y pack charg e fully .
18 If you hav e dif ficulty oper ating this phone, tr y the sugg estions below . If you still have troub le, call 1 800 722-9125. If the phone doesn’ t w ork at all, check these items first: • Make sure the A C adapter is plugged in. • Make sure the telephone line cord(s) is plugg ed firmly into the base unit and the modular telephone jack.
19 If the phone does not ring when y ou r eceive a call: • Make sure the handset ringer is on. • Make sure the telephone line cord(s) is connected f ir mly to the base and the modular telephone jack(s). • Make sure the A C adapter is plugged firmly into an outlet not controlled by a wall s witch.
Een belangrijk punt na aankoop van elk apparaat AT&T 9002 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen AT&T 9002 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens AT&T 9002 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding AT&T 9002 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over AT&T 9002 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van AT&T 9002 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de AT&T 9002 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met AT&T 9002 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
