Gebruiksaanwijzing /service van het product CS428 van de fabrikant ATEN Technology
Ga naar pagina of 41
4 Console / 8 Port KVM Switch CS428 User Manual www.aten.com cs428_2007-05.book Page i T hursday, May 17, 2007 5:08 PM.
CS428 User Manual ii FCC Information This is an FCC Class A product. In a domestic environment this product may cause radio interference in which cas e the user may be required to tak e adequate measures. This equipment has been test ed and found to comply with the limit s for a Class A digital device, pursuant to Part 15 of the FCC Rules.
CS428 User Manual iii User Information Online Registration Be sure to register your product at our online support center: International – http :/ /supp ort.
CS428 User Manual iv Package Content s The basic CS428 package consists of: 1 CS428 KVM Switch 2 KVM Cable Sets (2L-1701S) 1 Power Adapter 1 Rack Mount Kit 1 User Manual* Check to make sure that all the comp onents are present and that nothing got damaged in shipping .
CS428 User Manual v Content s FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii SJ/T 11364-2006.
CS428 User Manual vi F3 LIST: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 F4 SCAN: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 F5 ADM: . . . . . . .
CS428 User Manual vii About this Manual This User Manual is provided to help you get the most from your c/c system. It covers all aspects of installation, configurati on and op erati on. An overview of the information fou nd in th e manual is provided below.
CS428 User Manual viii Conventions This manual uses the following conven tio ns: Product Information For information abo ut all ATEN produ cts and how they can help you connect without limits, vi si t ATEN on the Web or co ntact an ATEN Authorized Reseller.
1 Chapter 1 Introduction Overview The CS-428 KVM Switch is a control unit that allows fou r independent keyboard, mouse, and moni tor Consoles to access eight computers, either independently or on a multiuser shared ba sis, in a convenient, cost effective manner.
CS428 User Manual 2 Features 4 Consoles Control 8 Computers Up to four users can operate up to 64 computers (via cascading to CS- 138A, CS-9138, CS-12 8A, or CS-124A) at the sam e time Eac.
1. Introduction 3 Requirement s Console A VGA, SVGA, or Multisync monitor capable of the highest resolution that you will be using on any com puter in the in stallation. If a monitor switches to a computer us ing a resolution that is higher th an the resolution that the monito r can support, serious damage to the mo nitor may result.
CS428 User Manual 4 Component s Front Panel No. Component Description 1 Port LEDs The Port LEDs provide status information about their corresponding Computer Ports.
1. Introduction 5 Rear Panel No. Component Desc ription 1 Power Switch A rocker switch to power the system on and off. 2 Console 3 and 4 Connectors Use KVM Cable sets (see Cables , page 3), to connect the components that make up Consoles 3 and 4 to these ports.
CS428 User Manual 6 This Page Intentionally Left Blank cs428_2007-05.book Page 6 T hur sday, May 17, 2007 5: 08 PM.
7 Chapter 2 Hardware Setup S t acking and Mounting The CS428 can be placed on the deskt op or it can be rack mounted, as described in the sections that fo llo w.
CS428 User Manual 8 2. Use the screws that came with the rack mount kit to screw the mounting brackets into the sides of the unit, as shown in the diagram below: 3.
2. Hardware Setup 9 Note: When you turn the unit On, it undergoes a Power On Self T est. If there is a problem, Port LEDs 1 - 4 flash repeatedly according to a pattern that indicates what the problem is. See see Power On Self Test , page 31 for details.
CS428 User Manual 10 To set up a two stage installation, do the following: 1. Make sure that power to all the devices you will be connecting up, including all preexisting devices on the installation, have been turned off (unplug the power cords of any computers that have the Keyboard Power On function; unplu g the First Stage unit).
11 Chapter 3 Basic Operation Hot Plugging The Master View CS428 support s hot plugging - compo nents can be removed and added back into the installation by unplugging their cables from the KVM ports without the need to shut the unit down. In o rder for hot plugging to work properly, however, these pro cedures must be followed: 1.
CS428 User Manual 12 Port Numbering Each computer on the installation is assigned a unique Port Number (PN). The PN is a one or two segment number that is determined by the Stage Level and KVM port of the KVM switch that the co mputer is connected to.
13 Chapter 4 OSD Operation OSD Overview On Screen Display (OSD), provides a menu driven interface to handle the computer switching procedur e. All operations start from the OSD Main Menu. To activate the Main Menu, tap either Ctrl key twi ce. Note: 1.
CS428 User Manual 14 When you invoke the OSD, a screen similar to the one below appears: Note: 1. The diagram depicts the Administra tor's Main Screen. The User Main Screen does not show the F2 and F5 function, since th ey are reserved for the Administrator and can't be accessed by ordinary Users.
4. OSD Operation 15 OSD Navigation T o dismiss the menu, and d eactivate the OSD, Click the X at the upper right corner of the OSD W indow; or press [Esc] . T o Logout, click F8 or the Z Z Z symbol at the top of the Main Screen, or press [F8] .
CS428 User Manual 16 OSD Main Menu Headings OSD Functions OSD functions are used to configure an d control the OSD. For example, you can: rapidly switch to any port; scan selected ports only; limit the list you wish to view; designate a port for Quick View scanning; create or edit a port name; or make OSD setting adjustments.
4. OSD Operation 17 F2 EDIT : This is an Admi nistrator function. To help remem ber which computer is attached to a particular port, every por t can be given a name. The Edit function allows the Administrator to create, m odify, or delete po rt names.
CS428 User Manual 18 F3 LIST : This function lets you broaden or na rro w the scope of which ports the OSD lists. This will be different for each Console, depending on the choices made for that Console.
4. OSD Operation 19 F4 SCAN: Clicking th e F4 field, o r pressing [F 4] initiates Scan Mode , in which the OSD cycles through all th e ports that have been sel ected for scanning with the Scan Mode setting (see SCAN MODE , page 22). When you want to stop at a particular location, press the [Spacebar] to stop scanning.
CS428 User Manual 20 F5 ADM: F5 allows an Admi nistrator to configur e the OSD operation of the Console. To change a setting Double Click it; or use the Up and Down Arrow Keys to mov e the highlight bar to it then press [Enter] .
4. OSD Operation 21 Setting Function SET ACCESSIBLE PORTS This function allows Administrators and Users to select which Ports can be accessed from a pa rticular Console. Move the highlight bar to the target computer, then press [Enter] or the [Sp acebar] to toggle access On and Off.
CS428 User Manual 22 F6 Set: [F6] allows you to configure the OSD settings for the Console you are working at. To change a setting: 1. Double Click it; or move the highlight bar to it, then press [Enter] 2. Press [Esc] to activate it. After you select an item, a submenu with further choices appears.
4. OSD Operation 23 (Continued from previous page.) Setting Function SCAN DURA TION Determines how long the display dwells on each por t when it cycles through the selected ports in Quick View Scan Mode . Key in a value from 1 - 255 seconds, then press [Enter] .
CS428 User Manual 24 F7 QV You can broaden or narrow the number of ports that get automati cally scanned by selecting only the ones you want wi th the QV (Quick View Scan) function. [F7] is a toggle that selects or deselects the currently highligh ted port for the Quick View Scan ning function (see F4, above).
25 Appendix Safety Instructions General Read all of these instructions. Save them for future reference. Follow all warnings and instructions marked on the dev ice. Do not place the device on any unstable su rf ace (cart, stand, table, etc.
CS428 User Manual 26 T o help protect y our system from sudden, transient increases and decreases in electrical power , use a su rge suppressor , line conditioner , or un-interruptible power supply (U PS). Position system cables and power cable s carefully; Be sure that nothing rests on any cables.
Appendix 27 Rack Mounting Before working on the rack, ma ke su re that the stabilizer s are secured to the rack, extended to the floor , and that the full w eight of the rack rests on the floor . Install front and side stabilizers on a single rack or front stabilizers for joined multiple ra cks before work ing on the rack.
CS428 User Manual 28 T echnical Support International North America When you contact u s, please have the followin g information ready beforehand: Product model number, serial number , and date of purchase. Y our computer configuration, includin g operatin g system, revision level, expansion cards, and software.
Appendix 29 Master View - Computer Connection T ables Switches Ty p e Computers 1 CS428 1 - 8 2 CS-128A / CS-138A / CS-9138 8 - 15 3 CS-128A / CS-138A / CS-9138 15 - 22 4 CS-128A / CS-138A / CS-9138 2.
CS428 User Manual 30 Specifications Function Specification Computer Connections Direct 8 Max 64 (via Cascade) Port Selection OSD (On Screen Display Connectors Console 1 & 2 Keyboard 2 x 6-pin Mini.
Appendix 31 OSD Factory Default Settings Power On Self T est When you turn the unit On, it undergoes a Power On Self Test. If there is a problem, Port LEDs 1 - 4 flash repeatedly according to a pattern that indicates what the problem is: If any of these problems o ccur, turn the Switch Off, then turn it On again.
CS428 User Manual 32 T roubleshooting Symptom Possible Cause Action Keyboard and/or Mouse not responding. The connection f rom the selected port to the targ et comput er has been broken, or the compute r is turned OFF . Check the Online LED for the selected port.
33 Index C Cables, 3 Components Front Panel, 4 Rear Panel, 5 Connection Tables, 29 F Factory Default Settings, 31 Features, 2 H Hot Plugging, 11 I Installation Cascaded, 9 Single Station, 8 L Limited .
Een belangrijk punt na aankoop van elk apparaat ATEN Technology CS428 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen ATEN Technology CS428 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens ATEN Technology CS428 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding ATEN Technology CS428 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over ATEN Technology CS428 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van ATEN Technology CS428 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de ATEN Technology CS428 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met ATEN Technology CS428 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
