Gebruiksaanwijzing /service van het product A88028 van de fabrikant Athena Technologies
Ga naar pagina of 16
1 SERVICE AND INSTALLATION Installation & Servicing Instructions PLEASE LEAVE THESE INSTRUCTIONS WITH THE USER FOR USE WITH NATURAL GAS ONLY G .C. No. 32 170 19 ÿ Product Code No. A88028 The Data Badge and Serial Number are located on the left hand side of the back panel.
2 CONTENTS LAYOUT INTRODUCTION AND GENERAL INST ALLATION REQUIREMENTS 1.0 TECHNICAL DA TA 2.0 CONDITIONS OF INSTALLA TION 2.1 SITING GENERAL 2.2 FLUES AND CHIMNEYS 2.2.1 Brick Chimney, 178mm diameter (7 inch) S tone or Lined Flue and 125mm diameter (5 inch) Flue 2.
3 INTRODUCTION 1.0 TECHNICAL DATA GENERAL INST ALLATION REQUIREMENTS NO COMPONENT OF THIS FIRE IS MANUFACTURED FROM ASBESTOS OR ASBESTOS RELA TED PRODUCTS.
4 2.1 SITING GENERAL This fire is suitable for hearth mounting only on a non-combustible hearth at least 13mm thick and measuring at least 630mm wide by 330mm deep. Its top surface should preferably be 50mm above the floor level in order to discourage the placing of carpets or rugs over it.
2.2.2 PRE-CAST FLUE OF MINIMUM SIZE (Fig. 2) This fire can be installed into a properly constructed pre-cast flue conforming to B.S. 1289 : 1975 or B.S.
6 2.2.3 METAL FLUE BOX/125mm DIAMETER FLUES (Figs. 3A and 3B) This fire may be installed in a double walled or insulated metal box built to the requirements of B.S. 715 e.g. Selkirk, Product Code Number 0404805, using our fixing kit G .C. Number 159 634 ÿ Number 992137.
2.3 SHELF HEIGHT AND SIDE CLEARANCES The fire may be fitted beneath a shelf. 2.3.1 COMBUSTIBLE SHELF The underside of a combustible shelf not more than 150mm deep must be at least 923mm from the hearth which gives a clearance of 237mm above the fire. For deeper shelves, add 13mm shelf height for every 25mm increase in depth.
8 3.3 METHOD OF INSTALLA TION There are two methods for securing the fire to the wall which are: (a) Fixing by tension cable. (b) Screwing the fire directly to the wall. It is recommended, where drilling holes in the front face of the fireplace surround is unacceptable or otherwise risky e.
Fig. 6 73mm 115mm 3.3.2 FIXING DIRECTLY TO SURROUND FACE Mark the four positions of the fixing holes on the front face of the fireplace surround using the fire as a template.
10 4.0 COMMISSIONING 4.1 INSTALL FUEL EFFECT COMPONENTS The fuel effect components comprise: (a) Rear Coal (b) Two Side Cheeks (c) Coal Bed (d) Nine Loose Coals The Coal Bed and the loose coals are illustrated in Fig. 7A. The fire is supplied with the rear coal and side cheeks already fitted as illustrated in Fig.
11 4.2 CHECK GAS PRESSURE Remove the pressure test point screw located on the injector feed pipe just left of centre on the fire. Connect a pressure gauge, slide the control knob down to the PILOT/IGNITION position. Keep the knob depressed after the pilot has lit to activate the FSD and then slide the knob to the HIGH position.
12 4.4 TEST FOR SPILLAGE A test for spillage must be made before the installed fire is left with the user . This is carried out in the following manner.
13 6.0 SERVICING INSTRUCTIONS IMPORTANT NOTES 1. Turn off the gas supply to the fire before starting any servicing. 2. Always test for gas soundness after servicing or exchanging any component. 3. Remove the fire from the surround and inspect the catchment space for build up of debris on every service visit.
14 6.4 PILOT ASSEMBLY The pilot is an atmosphere sensing device and must be replaced as a complete unit. Repair must not be undertaken. NOTE: If the fire keeps going out or exhibits signs of nuisance shut off, check the operation of the pilot as follows:- (a) Inspect the pilot flame, if suspect check the gas supply.
15 The following are possible fault conditions. Check the items mentioned and repair or replace parts as necessary. The list is not exhaustive but a fair outline of possible faults. 1. No Spark (a) Check spark by manually operating the micro switch. (b) The battery may be exhausted.
ÿ PAR T NUMBER DESCRIPTION 822309 Gas Valve / FSD Assembly 990274 Control Knob 822308 Pilot Assembly (Natural Gas) 993911 Spark Lead 822238 Ignition Unit 992232 Rear Coal 992234 Coal Bed 992169 Loose Coals (9 off) 992178 Left Side Cheek 992179 Right Side Cheek 16 8.
Een belangrijk punt na aankoop van elk apparaat Athena Technologies A88028 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Athena Technologies A88028 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Athena Technologies A88028 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Athena Technologies A88028 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Athena Technologies A88028 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Athena Technologies A88028 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Athena Technologies A88028 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Athena Technologies A88028 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
