Gebruiksaanwijzing /service van het product 915 van de fabrikant Pioneer
Ga naar pagina of 76
AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-815 VSX-915 Register y our pr oduct at: www .pioneerelectr onics.com • Protect y our ne w in vestment The details of your purchase will be on file for reference in the event of an insurance claim such as loss or theft.
W ARNING – TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. D1-4-2-1_En IMPORT ANT NOTICE – THE SERIAL NUMBER FOR THIS EQUIPMENT IS L OCA TED IN THE REAR. PLEASE WRITE THIS SERIAL NUMBER ON YOUR ENCL OSED W ARRANTY CARD AND KEEP IN A SECURE AREA.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Contents 01 Before you start Introduction to home theater . . . . . . . . . . . . . 6 Checking what’s in the box . . . . . . . . . . . . . . . 6 Loading the batteries . . . . . . . . . . . . . . . . . . . 7 Installing the receiver . . . . . . . . . .
English Italiano Français Nederlands Español Deutsch 10 Controlling the rest of your system Setting the remote to control other components . . . . . . . . . . . . . . . . . . . . . . . . . 55 Selecting preset codes directly . . . . . . . . . . . 55 Programming signals from other remote controls .
Before you start 01 6 En Chapter 1: Before you start Introduction to home theater You are probably used to using stereo equipment to listen to music, but may not be used to home theater systems that give you many more options (such as surround sound) when listening to soundtracks.
Before you start 01 7 En English Français Deutsch Nederlands Italiano Español Loading the batteries Caution Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following precautions: • Never use new and old batteries together.
5 minute guide 02 8 En Chapter 2: 5 minute guide Listening to Surround Sound This receiver was designed with the easiest possible setup in mind, so with the following quick setup guide, you should have your system hooked up for surround sound in no time at all.
5 minute guide 02 9 En English Français Deutsch Nederlands Italiano Español 3 Connect your speakers. A complete setup of eight speakers (including the subwoofer) is shown here but everyone’s home setup will vary. Simply connect the speakers you have in the manner shown below.
5 minute guide 02 10 En Make sure that the speaker cable you’re using is properly prepared with about 3 / 8 in. (10 mm) of insulator stripped from each wire, with the exposed wire strands twisted together ( fig. A ). Unscrew the terminal a few turns until there is enough space to insert the exposed wire ( fig.
5 minute guide 02 11 En English Français Deutsch Nederlands Italiano Español Using the Quick Setup You can use the Quick Setup to get your system up and running with just a few button presses. The receiver automatically makes the necessary settings after you have selected your speaker setup, room size and listening position.
Quick surround sound setup 03 12 En Chapter 3: Quick surround sound setup Automatically setting up for surround sound (MCACC) The Auto Multi-Channel Acoustic Calibration (MCACC) setup measures the aco.
Quick surround sound setup 03 13 En English Français Deutsch Nederlands Italiano Español If the noise level is too high, NOISY! blinks in the display for five seconds.
Quick surround sound setup 03 14 En Other problems when using the Auto MCACC Setup If the room environment is not optimal for the Auto MCACC Setup (too much background noise, echo off the walls, obstacles blocking the speakers from the microphone) the final settings may be incorrect.
Connecting up 04 15 En English Français Deutsch Nederlands Italiano Español Chapter 4: Connecting up Making cable connections Make sure not to bend the cables over the top of this unit (as shown in the illustration). If this happens, the magnetic field produced by the transformers in this unit may cause a humming noise from the speakers.
Connecting up 04 16 En S-video cables S-video cables give you clearer picture reproduction than standard RCA video cables by sending separate signals for the luminance and color. Component video cables Use component video cables to get the best possible color reproduction of your video source.
Connecting up 04 17 En English Français Deutsch Nederlands Italiano Español Connecting a DVD player and TV This page shows you how to connect your DVD player and TV to the receiver. 1 Connect a coaxial digital audio output on your DVD player to the DIGITAL COAX 1 (DVD/LD) input on this receiver.
Connecting up 04 18 En Connecting the multichannel analog outputs For DVD Audio and SACD playback, your DVD player may have 5.1 channel analog outputs.In this case, you can connect the multichannel analog outputs to the multichannel inputs of this receiver as shown below.
Connecting up 04 19 En English Français Deutsch Nederlands Italiano Español Connecting other audio components The number and kind of connections depends on the kind of component you’re connecting. 1 Follow the steps below to connect a CD-R, MD, DAT, tape recorder or other audio component.
Connecting up 04 20 En compatible player. However, the connected PC, DVD player, set-top box, etc. must be able to output WMA9 Pro format audio signals through a coaxial or optical digital output.
Connecting up 04 21 En English Français Deutsch Nederlands Italiano Español Using the component video jacks Component video should deliver superior picture quality when compared to composite video. A further advantage (if your source and TV are both compatible) is progressive-scan video, which delivers a very stable, flicker-free picture.
Connecting up 04 22 En Connecting antennas Connect the AM loop antenna and the FM wire antenna as shown below. To improve reception and sound quality, connect external antennas (see Using external antennas below). Always make sure that the receiver is switched off and unplugged from the wall outlet before making or changing any connections.
Connecting up 04 23 En English Français Deutsch Nederlands Italiano Español Connecting the speakers A complete setup of eight speakers (including the subwoofer) is shown here but everyone’s home setup will vary. Simply connect the speakers you have in the manner shown below.
Connecting up 04 24 En Make sure that the speaker cable you’re using is properly prepared with about 3 / 8 in. (10 mm) of insulator stripped from each wire, with the exposed wire strands twisted together ( fig. A ). Unscrew the terminal a few turns until there is enough space to insert the exposed wire ( fig.
Connecting up 04 25 En English Français Deutsch Nederlands Italiano Español • Make sure no exposed speaker wire is touching the rear panel, this may cause the receiver to turn off automatically. Overhead view of speaker setup You can also refer to the 3-D speaker setup illustration on page 10.
Connecting up 04 26 En Operating other Pioneer components Many Pioneer components have SR CONTROL jacks which can be used to link components together so that you can use just the remote sensor of one component. When you use a remote control, the control signal is passed along the chain to the appropriate component.
Controls and displays 05 27 En English Français Deutsch Nederlands Italiano Español Chapter 5: Controls and displays Front panel 1 Input select buttons Press to select an input source.
Controls and displays 05 28 En 7 PHONES jack Use to connect headphones. When the headphones are connected, there is no sound output from the speakers. 8 LISTENING MODE buttons STANDARD Press for Standard decoding and to switch between the various Pro Logic IIx and Neo:6 options (page 34).
Controls and displays 05 29 En English Français Deutsch Nederlands Italiano Español Display 1 SIGNAL SELECT indicators Lights to indicate the type of input signal: AUTO Lights when AUTO signal select is on. SB Depending on the source, this lights when a signal with surround back channel encoding is detected.
Controls and displays 05 30 En Lights when a broadcast is being received. 11 Speaker indicators Lights to indicate the current speaker system, A and/or B (page 62). 12 Character display 13 Neo:6 When the ( STANDARD ) Neo:6 mode of the receiver is on, this lights to indicate Neo:6 processing.
Controls and displays 05 31 En English Français Deutsch Nederlands Italiano Español 3 MULTI CONTROL buttons Press to select control of other components (see Controlling the rest of your system on page 55).
Controls and displays 05 32 En 8 Component control buttons The main buttons ( , , etc.) are used to control a component after you have selected it using the MULTI CONTROL buttons.
Controls and displays 05 33 En English Français Deutsch Nederlands Italiano Español EFFECT/CH SEL Press repeatedly to select a channel, then use LEVEL +/– to adjust the level (see Tip on page 50).
Listening to your system 06 34 En Chapter 6: Listening to your system Important • Certain features explained in this section will not be possible depending on the source (for example, PCM 88.
Listening to your system 06 35 En English Français Deutsch Nederlands Italiano Español • 2 Pro Logic IIx MUSIC – Up to 7.1 channel sound, especially suited to music sources • 2 Pro Logic IIx GAME – Up to 7.1 channel sound, especially suited for video games • 2 PRO LOGIC – 4.
Listening to your system 06 36 En surround sound. Use with Dolby Pro Logic for a stereo surround effect. You can also use with Dolby Digital sources for a wider stereo field than the Standard modes. • 7-STEREO – This can be selected to give multichannel sound to a stereo source, using all of the speakers in your setup.
Listening to your system 06 37 En English Français Deutsch Nederlands Italiano Español 1 With Neo:6 MUSIC mode active, press EFFECT/CH SEL repeatedly to select C.
Listening to your system 06 38 En Choosing the input signal You need to hook up a component to both analog and digital inputs on the rear of the receiver to select between input signals. 1 1 Press SIGNAL SELECT on the front panel to select the input signal corresponding to the source component.
Listening to your system 06 39 En English Français Deutsch Nederlands Italiano Español Using the surround back channel (Extended mode) • Default setting: EXT. ON You can have the receiver automatically use 6.1 or 7.1 decoding for 6.1 encoded sources (for example, Dolby Digital EX or DTS-ES), or you can choose to always use 6.
Listening to your system 06 40 En Using the Virtual Surround Back mode (VirtualSB) Selecting this mode allows you to hear a virtual back channel through your surround speakers. For example, you can choose to listen to sources with no surround back channel information (for example, 5.
Listening to your system 06 41 En English Français Deutsch Nederlands Italiano Español Using Loudness and Midnight listening The Loudness listening feature can be used to get good bass and treble from music sources at low volume levels. The Midnight listening feature allows you to hear effective surround sound of movies at low volume levels.
Listening to your system 06 42 En Playing other sources 1 Turn on the power of the playback component. 2 Turn on the power of the receiver. 3 Select the source you want to playback. Use the MULTI CONTROL buttons (or INPUT SELECT ). 1 4 Start playback of the component you selected in step 1.
The System Setup menu 07 43 En English Français Deutsch Nederlands Italiano Español Chapter 7: The System Setup menu Making receiver settings from the System Setup menu The following section shows y.
The System Setup menu 07 44 En • SB 2ND Z – Select to use the (surround back) B speaker terminals to listen to stereo playback in another room (see Second Zone speaker B setup on page 62). • SB BIAMP – Select this setting if you’re bi- amping your front speakers (see Bi-amping your front speakers on page 63).
The System Setup menu 07 45 En English Français Deutsch Nederlands Italiano Español 1 Select ‘ CH LEVEL’ from the Manual MCACC setup menu. You’ll hear test tones from each speaker in turn. Since the left speaker is the main reference speaker, the level is fixed and cannot be changed.
The System Setup menu 07 46 En Acoustic Calibration EQ Acoustic Calibration Equalization is a kind of room equalizer for your speakers (excluding the subwoofer). It works by measuring the acoustic characteristics of your room and neutralizing the ambient characteristics that can color the original source material.
The System Setup menu 07 47 En English Français Deutsch Nederlands Italiano Español curve, this will give you a reference point from which to start (see Copying your Acoustic Calibration EQ settings above for how to do this). 1 Select ‘ C1 ADJ ’ or ‘ C2 ADJ ’ from the Manual MCACC setup menu.
The System Setup menu 07 48 En Manual speaker setup This receiver allows you to make detailed settings to optimize the surround sound performance. You only need to make these settings once (unless you change the placement of your current speaker system or add new speakers.
The System Setup menu 07 49 En English Français Deutsch Nederlands Italiano Español output bass sound continuously or you want deeper bass (the bass frequencies that would normally come out the front and center speakers are also routed to the subwoofer).
The System Setup menu 07 50 En Adjust the level of each speaker as the test tone is emitted. 1 5 When you’re finished, press RETURN. Tip • You can change the channel levels at any time by using EFFECT/CH SEL and +/– on the remote control. You can set two channel levels: one for DVD 5.
Using the tuner 08 51 En English Français Deutsch Nederlands Italiano Español Chapter 8: Using the tuner Listening to the radio The following steps show you how to tune in to FM and AM radio broadcasts using the automatic (search) and manual (step) tuning functions.
Using the tuner 08 52 En Saving station presets If you often listen to a particular radio station, it's convenient to have the receiver store the frequency for easy recall whenever you want to listen to that station. This saves the effort of manually tuning in each time.
Using the tuner 08 53 En English Français Deutsch Nederlands Italiano Español Tip • To erase a station name, simply repeat steps 1-3 and input four spaces instead of a name. • Once you have named a station preset, you can press TUNER DISPLAY when listening to a station to switch the display between name and frequency.
Making recordings 09 54 En Chapter 9: Making recordings Making an audio or a video recording You can make an audio or a video recording from the built-in tuner, or from an audio or video source connected to the receiver (such as a CD player or TV).
Controlling the rest of your system 10 55 En English Français Deutsch Nederlands Italiano Español Chapter 10: Controlling the rest of your system Setting the remote to control other components Most components can be assigned to one of the MULTI CONTROL buttons using the component’s manufacturer preset code stored in the remote.
Controlling the rest of your system 10 56 En 5 Use / (cursor up/down) to select the manufacturer’s name from the list then press ENTER. 6 Use / (cursor up/down) to select the proper code from the list, then try using this remote control with your component.
Controlling the rest of your system 10 57 En English Français Deutsch Nederlands Italiano Español Certain buttons represent operations that cannot be learned from other remote controls. The buttons available are shown below: 6 To program additional signals for the current component repeat steps 4 and 5.
Controlling the rest of your system 10 58 En When direct function is on, any component you select (using the MULTI CONTROL buttons) will be selected by both the receiver and the remote control. When you turn direct function off, you can operate the remote control without affecting the receiver.
Controlling the rest of your system 10 59 En English Français Deutsch Nederlands Italiano Español Controls for TVs This remote control can control components after entering the proper codes or teaching the receiver the commands (see Setting the remote to control other components on page 55 for more on this).
Controlling the rest of your system 10 60 En Controls for other components This remote control can control these components after entering the proper codes or teaching the receiver the commands (see Setting the remote to control other components on page 55 for more on this).
Controlling the rest of your system 10 61 En English Français Deutsch Nederlands Italiano Español REC STOP ( SHIFT+ ) Stops recording. DVR player Number buttons Directly access tracks on a program source. CD/MD/CD-R/VCR/LD player Use the number buttons to navigate the on-screen display .
Other connections 11 62 En Chapter 11: Other connections Caution • Before making or changing the connections , switch off the power and disconnect the power cord from the power outlet. Plugging in components should be the last connection you make with your system.
Other connections 11 63 En English Français Deutsch Nederlands Italiano Español • SP AB – Sound is output from speaker system A (up to 5 channels, depending on the source), the two speakers in speaker system B, and the subwoofer. Multichannel sources (heard through speaker system A) are downmixed for stereo output from speaker system B.
Other connections 11 64 En Caution • Make sure you use a parallel (not series, which are fairly uncommon) connection when bi-wiring your speakers. • Don't connect different speakers from the same terminal in this way.
Other connections 11 65 En English Français Deutsch Nederlands Italiano Español • Use a 3-ringed miniplug SR+ cable 1 to connect the CONTROL IN jack of this receiver with the CONTROL OUT of your plasma display. Before you can use the extra SR+ features, you need to make a few settings in the receiver.
Other Settings 12 66 En Chapter 12: Other Settings The Input Assign menu You only need to make settings in the Input Assign menu if you didn’t hook up your digital equipment according to the default settings for the digital inputs, or if you have connected equipment using component video cables.
Other Settings 12 67 En English Français Deutsch Nederlands Italiano Español 2 Select the number of the component video input to which you’ve connected your video component. Use / (cursor left/right) to do this. • The numbers correspond with the numbers beside the inputs on the back of the receiver.
Other Settings 12 68 En 1 Select DUAL MONO from the OTHER setup menu. 2 Use / (cursor up/down) to choose the setting that you want. • CH1 – Only channel 1 is played • CH2 – Only channel 2 is played • CH1 CH2 – Both channels are played through the front speakers 3 When you're finished, press RETURN .
Additional information 13 69 En English Français Deutsch Nederlands Italiano Español Chapter 13: Additional information Troubleshooting Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below.
Additional information 13 70 En Considerable noise in radio broadcasts. • T une in the correct frequency. • Connect the antenna (refer to page 22). • Route any loose cables away from the antenna terminals and wires. • F ully extend the FM wire antenna, position for best reception, and secure to a wall.
Additional information 13 71 En English Français Deutsch Nederlands Italiano Español No sound is output or a noise is output when software with DTS is played back. • Set the digital volume level of the player to full, or to the neutral position. • Make sure the player's settings are correct and/or the DTS signal out is on.
Additional information 13 72 En Resetting the main unit Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this. 1 Switch the receiver into standby. 2 While holding down the TONE button, press and hold the STANDBY/ON button for about three seconds.
Additional information 13 73 En English Français Deutsch Nederlands Italiano Español Specifications Amplifier section • Continuous power output (stereo) 1 Front: VSX-815 . . . 100 W (20–20,000 Hz, THD 0.7%, 8 Ω ) VSX-915 . . . 120 W (20–20,000 Hz, THD 0.
Additional information 13 74 En • FM Tuner Section Frequency Range . . . . . . . . 87.5 MHz to 108 MHz Usable Sensitivity . . . . . . . . . . Mono:13.2 dBf, IHF (1.3 µV/ 75 Ω ) 50 dB Quieting Sensitivity . . . . . . . Mono: 20.2 dB Stereo: 38.6 dBf Signal-to-Noise Ratio .
Additional information 13 75 En English Français Deutsch Nederlands Italiano Español S001_En Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your musical enjoyment. Now it’s time to consider how you can maximize the fun and excitement your equipment offers.
Published by Pioneer Corporation Copyright©2004 Pioneer Corporation All rights reserved <04L00001> Printed in <XRB3047-A> Should this product require service in the U.
Een belangrijk punt na aankoop van elk apparaat Pioneer 915 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Pioneer 915 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Pioneer 915 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Pioneer 915 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Pioneer 915 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Pioneer 915 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Pioneer 915 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Pioneer 915 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
