Gebruiksaanwijzing /service van het product PT2275SW/PT2285PW van de fabrikant Planar
Ga naar pagina of 32
PT2275SW / PT2285PW T ouch Screen LCD Monitor USER’S GUIDE www .planartouch.com.
Important Recycle Instructions: Lamp(s) inside this product contains mercury . This product may contain other electronic waste that can be hazardous if not disposed of properly . Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW .
T able of Contents Usage Notice Precautions............................................................................................................................. 1 Introduction About PT2275SW / PT2285PW .........................................
Usage Notice ! W arnin g - T o prevent the risk o f fi re or shock hazards, do not expose this product to rain or moisture. ! W arnin g - Please do not open or disassemble the product as this ma y cause e l ec tri c s h oc k.
Introduction About PT2275SW / PT2285PW The PT2275SW / PT2285PW is a 22" fl at panel screen with an active matrix, thin- fi lm transistor (TFT) liquid crystal display (LCD).
T ouch Screen for PT2285PW • Project Capacitive touch screen for fi nger input only • Surface: Glare treatment • Interface: USB controller • T ransmittance: 9 0%± 5% • Driver: Windows ® 7, VIST A 64/32 bits, XP , 2000, XP Embedded Express, Linux, Apple ® Mac OS.
4 Package Overview LCD Display Power Cord VGA Signal Cable RS-232 Cable (PT2275SW only) USB Cable ( A to B) Audio-in Cable DVI-D Cable Cable Cover Screw T ouch Screen Driver Installation CD-ROM Landing Strip User ’s Guide xxxxxxxxx / xxxxxxxxx xxxxxxxxx USER’S GUIDE www.
Installation Product Overview • Front View PT2275SW PT2285PW • PT2275SW Bottom View (W ithout Stand) VGA IN AC IN AUDIO DVI IN RS-232 USB • PT2285PW Bottom View (W ithout Stand) VGA IN AC IN Aud.
Start Y our Installation 1. Lay the LCD fl at on an even surface. 2. Remove the stand back cover by pulling in the direction of the arrow as seen in step 2 diagram. 3. Move the stand into position as seen in step 3 diagram. 4. Connect the cables to the appropriate connectors as seen in Step 4 diagram.
5. T ake the optional cable cover and screw from the accessory box. Position all cables under the cover lip as seen in the step 5 diagram. 6. Using a Philips Head screwdriver , insert the screw (CPMSP M3x10) into the cable cover and monitor as seen in the step 6 diagram.
8 Connecting the Display (Figure 9.1) T o setup this display , please refer to the following fi gure and procedures. 1. Be sure all equipment is turned off. 2. Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet (9.
9 (Figure 9.1) PT2275SW PT2285PW.
Kensington Security Slot The monitor can be secured to your desk or any other fi xed object with Kensington lock security products. The Kensington lock is not included.
VESA Mount Y our Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which de fi nes a physical mounting interface for fl at panel monitors, and corresponding with the standards of fl at panel monitor mounting devices, such as wall and table arms.
12 Remove the Deskstand Remove 4 screws and then remove hinge..
13 User Controls Side Panel Controls Icon key Name Menu Up Down Enter Power OSD Key Menu off status Menu on status Menu appear Menu disappear / return to main item Brightness Main item select up / Adj.
14 How to Use the OSD Menus Icon Key Name Menu Up Down Enter Power 1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the six functions in the main menu. 2. Choose the adjustment items by pressing the “Enter ” button.
15 On-Screen Display Menus Main OSD Menu: ITEM CONTENT Contrast The monitor luminance level control. Brightness The monitor backlight level control. Auto Adjust Fine-tune the image to full screen automatically . Left/Right Moving screen image horizontal position to left or right.
Appendix T roubleshooting If you are experiencing trouble with the LCD display , refer to the following. If the problem persists, please contact your local dealer or our service center .
W arning Signal If you see warning messages on your LCD screen, this means that the LCD display cannot receive a clean signal from the computer graphics card. Below are the three kinds of W arning Signal. Please check the cable connections or contact your local dealer or our service center for more information.
Product Dimensions PT2275SW 538.5 mm 383.8 mm 330.0 mm 73.2 mm 287.1 mm 327.74 mm Side View T op View Front View 18.
Rotate 330.0 mm 73.2 mm 573.1 mm 538.5 mm 287.1 mm 327.7 mm T op View Front View Side View 19.
PT2285PW 539.2 mm 384.1 mm 330.6 mm 71.9 mm 327.7 mm 287.1 mm T op View Front View Side View 20.
Rotate 330.6 mm 71.9 mm 573.4 mm 539.2 mm 287.1 mm 327.7 mm T op View Front View Side View 21.
Compatibility Modes Mode Resolution H-Frequency(khz) V -Frequency(hz) IBM VGA 720X400 31.47 70 IBM VGA 640X480 31.47 60 Apple MacII 640X480 35.00 66 VESA VGA 640X480 37.86 72 VESA VGA 640X480 37.50 75 VESA VGA 800X600 35.16 56 VESA VGA 800X600 37.88 60 VESA VGA 800X600 48.
T ouch Screen Driver Installation The PT2275SW is available with both RS232 and USB connections. The touch driver is located on the enclosed CD-ROM for these operating systems: Windows ® 7, VIST A 64/32 bits, XP , 2000, ME, 98, NT 4.0, CE, XP Embedded, Linux, Apple ® Mac OS.
PT2285PW Calibration Instructions: Calibrating the touch screen in Windows 7: 1. T ap the Start button, Control Panel and then Hardware and Sound. 2. Under T ablet PC Settings, tap Calibrate the screen for pen or touch input. 3. On the Display tab, under Display options, tap Calibrate and then Y es to allow the program to make changes.
25.
PT2275SW/PT2285PW Driver Install Instructions: If you are using a PC running Windows ® 7, VIST A, XP , 2000, ME, 98, NT4.0, follow the instructions below: 1. Power on the PC. 2. Be sure the USB or the RS-232 Serial cable is connected from the PC to the LCD display .
If you are using a PC running Windows ® CE, follow the instructions below (PT2275SW only): 1. Power on the computer . 2. Make sure that the RS232 or USB cable is connected to the computer . 3. Using Platform Builder , build an image fi le by following the step-by-step instructions found in the zipped fi le on the CD-ROM.
Product Registration and T echnical Support Register Y our Planar Products T oday Thank you for choosing Planar . T o assure you receive all the bene fi ts of your Planar product and services, register your Planar product today . Visit our website to register your product at http://www .
Planar Systems, Inc. Customer Service 24x7 Online T echnical Support: http://www .planar .com/ support 1 195 NW Compton Drive Beaverton, OR 97006-1992 T el: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the United States. Hours: 24 hours a day , 7 days a week © 201 1 Planar Systems, Inc.
Een belangrijk punt na aankoop van elk apparaat Planar PT2275SW/PT2285PW (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Planar PT2275SW/PT2285PW heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Planar PT2275SW/PT2285PW vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Planar PT2275SW/PT2285PW leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Planar PT2275SW/PT2285PW krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Planar PT2275SW/PT2285PW bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Planar PT2275SW/PT2285PW kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Planar PT2275SW/PT2285PW . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
