Gebruiksaanwijzing /service van het product GSD-503 van de fabrikant Planet Technology
Ga naar pagina of 20
10/100/1000Mbp s Gigabit Ethernet Switch GSD-503/GSD-504 GSD-803/GSD-804 User's Manual.
T rademarks Copyright © PLANET T echnology Corp. 2005. Content subjects to revision without prior notice. PLANET is a registered trademark of PLANET T echnology Corp.
FCC W arning This equipment has bee n tested an d found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferenc e when the equipment is operated in a commercial envi ronment.
1. INTRODUCTION 1.1 Package Content s Check the conten ts of your package for following part s: 。 Gigabit Ethernet Switch x1 。 User's manual x1 。 Power adap ter x1 If any of these are missi.
1.3 Product Features 。 Complies with IEEE802.3, 10Base-T , IEEE802.3u, 100Base-TX and IEEE802.3ab, 1000B ase-T 。 IEE802.3x, full-duplex flo w control compliant; back-press ure, half-duplex flow co.
1.4 Product Specifications Model GSD-503/GSD-504 GSD-803/GSD-804 Hardware Specification Network Ports 5 10/100/1000Base-T RJ-45 MDI/MDI-X ports 8 10/100/1000Base-T RJ-45 MDI/MDI-X ports 155 x 86 x 26 mm (503) 155 x 86 x 26 m m (803) Dimensions (W x D x H) 170 x 87 x 32mm (504) 170 x 87 x 32 mm (804) Weight (KG) 0.
.
2. INSTALLATION This section describes the functi onalities of the Gigabit Ethernet Switch’s components and guides how to install it on the desktop. Basic knowledge of net working is assumed. Please read this chapter completely before continui ng. 2.
This product also supports store-and-for ward forwarding scheme to ensure low latency and hig h d ata integrit y , eliminates unnecessar y traffic and relieves congestion on critical network paths.
Figure 2-5 & 2-6 show the front panel and rear panel of GSD-803 Figure 2-5 GSD-803 front panel Figure 2-6 GSD-803 rear panel Figure 2-7 & 2-8 show the front panel and rear panel of GSD-804 Figure 2-7 GSD-804 front panel Figure 2-8 GSD-804 rear panel 2.
receiving data over that port. 10 Green rating at 10Mbps. r Lit: indicate that the port is ope Blink: indicate that the switch is actively sending o receiving data over that port. ower Notice: 1. The device is a power-required device, it means, it will not work 2.
Note: When choosing a location, pleas e keep in mind the environmental restrictions discu ssed in Chapter 1, Section 1.4 Product S pecification. Step4: Connect your switch to net work devices. A. Co nn ect one end of a standard network cable to the 10/100/1000 RJ-45 ports on the Back of the switch.
3. SWITCH OPERATION 3.1 Address T able The Switch is implemented with an address table. This address table composed of many entries. Each entry is used to store the addr ess information of some node in network, including MAC address, port no, etc. This information comes from the learning process of Ethernet Swi tch.
3.4 Store-and-Forward S tore-and-Forward is one t ype of packet-forwarding techniques. A S tore-and-Forward Ethernet S witchi ng stores the incoming frame in an internal buffer , do the complete error checking before transmissi on. Therefore, no error packets occurrenc e, it is the best choice when a network needs efficiency and stability .
connection is established with another net work device (usually at Power On or Reset). This is done by detect the modes and speeds at the second of both device is connected a nd capable of, both 10Base-T and 100Base-TX devices can connect with the port in either Half- or Full-Duplex mode.
4. TROUBLESHOOTING This chapter contains information to help you solve pro blems. If Giga Switch is not functioning properly , make sure the Ethernet S witch was set up according to instru ctions in this manual.
This page intentionally left blank !.
Appendix A A.1 Switch's RJ-45 Pin Assignment s 1000Mbps, 1000Base T Cont act MDI MDI-X 1 BI_DA+ BI_DB+ 2 BI_DA- BI_DB- 3 BI_DB+ BI_DA+ 4 BI_DC+ BI_DD+ 5 BI_DC- BI_DD- 6 BI_DB- BI_DA- 7 BI_DD+ BI_.
RJ-45 Connector pi n assignment Contact MDI Media Dependant Interface MDI-X Media Dependant Interface - Cross 1 Tx + (transmit) RX + (receive) 2 Tx - (transmit) RX - (receive) 3 Rx + (receive) TX + (transmit) 4, 5 Not used 6 RX – (receive) TX – (transmit) 7, 8 Not used The standard cable, RJ-45 pin assignment The st andard RJ-45 recept acle/.
2010-A331 10-000.
Een belangrijk punt na aankoop van elk apparaat Planet Technology GSD-503 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Planet Technology GSD-503 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Planet Technology GSD-503 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Planet Technology GSD-503 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Planet Technology GSD-503 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Planet Technology GSD-503 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Planet Technology GSD-503 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Planet Technology GSD-503 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
