Gebruiksaanwijzing /service van het product UPS 1000 - 2200 van de fabrikant Powerware
Ga naar pagina of 24
UPS 1 0 0 0 - 220 0 V A User ’ s Manual.
.
P ow er w are 51 25 User ’ s Manual 1 0 0 0–220 0 V A 1019297 Revision A T able of contents 1. Introduction ............................................................................................................. 7 2. Installation ...........
Copyright 2002 The contents of this manual are the copyright of the publisher and may not be r epr oduced (even extracts) unless permission granted. Every care has been taken to ensur e the accuracy of the information contained in this manual, but no liability can be accepted for any errors or omission.
Requesting a Declaration of Conformity Units that are labeled with a CE mark comply with the following harmonized standards and EU directives: • Harmonized Standards: EN 50091-1-1 and EN 50091-2; IE.
Special Symbols The following are examples of symbols used on the UPS to alert you to important information: RISK OF ELECTRIC SHOCK - Indicates that a risk of electric shock is present and the associated warning should be observed.
1 0 0 0 - 2200 V A User ’ s Manual 1 0 1 9297 Revision A 7 1 P o w er w are 5125 – Introduction The Powerware ® 5125 uninterruptible power system (UPS) protects your sensitive electronic equipment from basic power problems such as power failures, power sags, power surges, undervoltage and overvoltage.
1 0 0 0 - 20 0 0 V A User ’ s Manual 1 0 1 9297 Revision A 8 2 Installation Inspecting the Equipment If any equipment has been damaged during shipment, keep the shipping cartons and packing materials for the carrier or place of pur chase and file a claim for shipping damage.
1 0 0 0 - 220 0 V A User ’ s Manual 1 0 1 9297 Revision A 9 NOTE. The batteries charge to 90% capacity in approximately 3 hours. However , it is recommended that the batteries charge for 24 hours after installation or long-term storage.
1 0 0 0 - 20 0 0 V A User ’ s Manual 1 0 1 9297 Revision A 10 Figure 4. PW5125 220 0i Rear P anel 3 Operation and Configuration Operating Modes Powerware 5125’ s front panel indicates the UPS status thr ough the UPS indicators. Figure 5 shows the UPS front panel indicators and controls.
1 0 0 0 - 220 0 V A User ’ s Manual 1 0 1 9297 Revision A 11 Standby Mode When the UPS is turned off and remains plugged into a power outlet, the UPS is in Standby mode. The indicator flashes and the bar graph indicators are off, indicating that power is not available from the UPS output r eceptacles.
1 0 0 0 - 20 0 0 V A User ’ s Manual 1 0 1 9297 Revision A 12 Bat tery Mode When the UPS is operating during a power outage, the alarm beeps once every four seconds and the indicator illuminates. When the utility power returns, the UPS switches to Normal mode operation while the battery recharges.
1 0 0 0 - 220 0 V A User ’ s Manual 1 0 1 9297 Revision A 13 T urning the UPS Of f T o turn off the UPS, pr ess and hold the Of f button until the long beep ceases (approximately five seconds). The indicator begins to flash and the UPS remains in Standby mode until you unplug the UPS from the power outlet.
1 0 0 0 - 20 0 0 V A User ’ s Manual 1 0 1 9297 Revision A 14 Netw ork T ransient P r otector The Network T ransient Pr otector , shown in Figur e 9, is located on the rear panel and has jacks labeled IN and OUT . This feature accommodates a single RJ–45 (10BaseT) network connector .
1 0 0 0 - 220 0 V A User ’ s Manual 1 0 1 9297 Revision A 15 Load Segments Load segments are sets of receptacles that can be controlled by power management software, providing an orderly shutdown and startup of your equipment. For example, during a power outage, you can keep key pieces of equipment running while you turn off other equipment.
1 0 0 0 - 20 0 0 V A User ’ s Manual 1 0 1 9297 Revision A 16 4 UPS Maintenance UPS and Bat tery Care For the best preventive maintenance, keep the area around the UPS clean and dust–free. If the atmosphere is very dusty , clean the outside of the system with a vacuum cleaner .
1 0 0 0 - 220 0 V A User ’ s Manual 1 0 1 9297 Revision A 17 How to Replace Extended Bat tery Modules Use the following procedure to replace EBMs: 1. Unplug the EBM cable from the UPS. 2. Replace the EBM. See “Recycling the Used Battery” on page 20 for proper disposal.
1 0 0 0 - 20 0 0 V A User ’ s Manual 1 0 1 9297 Revision A 18 Use the following procedure to replace internal batteries: 1. Remove the UPS front panel by pulling the top. 2. Slide up and remove the metal battery cover . 3. 1000 V A units. Disconnect the red battery cable on the front of the battery .
1 0 0 0 - 220 0 V A User ’ s Manual 1 0 1 9297 Revision A 19 4. 1500 and 2200 V A units. Pull the battery out onto a flat, stable surface. Press on the black tab on the battery cable connector to disconnect the battery . See “Recycling the Used Battery” on page 20 for proper disposal.
1 0 0 0 - 20 0 0 V A User ’ s Manual 1 0 1 9297 Revision A 20 Rec ycling the Used Bat ter y Contact your local recycling or hazardous waste center for information on proper disposal of the used battery . WARNING Do not dispose of the battery or batteries in a fire.
1 0 0 0 - 220 0 V A User ’ s Manual 1 0 1 9297 Revision A 21 Silencing an Audible Alarm T o silence the alarm for an existing fault, press the button. If UPS status changes, the alarm beeps, overriding the previous alarm silencing. The alarm does not silence if there is a low battery condition.
1 0 0 0 - 20 0 0 V A User ’ s Manual 1 0 1 9297 Revision A 22 n o i t i d n o C r o m r a l A e s u a C e l b i s s o P n o i t c A n o g n i n n u r s i S P U e h T e h t e s u a c e b r e w o p y r e t t a b r o h g i h o o t s i e g a t l o v t u p n i .
1 0 0 0 - 220 0 V A User ’ s Manual 1 0 1 9297 Revision A 23 6 Specifications T able 3. Model Specifications T able 4. W eights and Dimensions T able 5.
1 0 0 0 - 20 0 0 V A User ’ s Manual 1 0 1 9297 Revision A 24 e r u t a r e p m e T g n i t a r e p OC ° 0 4 o t C ° 0 1 C ° 5 2 : e c n a m r o f r e p y r e t t a b l a m i t p O e r u t a r e .
Een belangrijk punt na aankoop van elk apparaat Powerware UPS 1000 - 2200 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Powerware UPS 1000 - 2200 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Powerware UPS 1000 - 2200 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Powerware UPS 1000 - 2200 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Powerware UPS 1000 - 2200 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Powerware UPS 1000 - 2200 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Powerware UPS 1000 - 2200 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Powerware UPS 1000 - 2200 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
