Gebruiksaanwijzing /service van het product D2000/1 van de fabrikant Precision Power
Ga naar pagina of 23
AMPLIFIER MODELS D500/1 D1000/1 D2000/1 D3000/1.
T ABLE OF CONTENTS Congr atulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Ser vice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Caution . . . . . . . . . . . . . .
CONGRA TULA TIONS Thank y ou f or choosing Precision P o wer TM audio equipment. Designed and engineered in the USA, this product combines innov ative technology with the finest materials to consistently deliv er Absolutely State of the Ar t ™ perf ormance, sound quality , reliability , and v alue .
FEA TURES Adv anced Instrumentation Input Stage. 24dB/Octa v e; HP/LP/FULL; 30-4kHz Crossov er . Independent Line Output Crossov er 30-4kHz PWM P ower Supply T riple Dar lington Output Stage . AP-IV Protection Circuity QB ASS TM Bass Boost High V oltage Input Capability with -12dB Atten uation Switch.
SPECIFICA TIONS Nominal Power Ratings MODEL 4ohm MONO 2ohm MONO 1ohm MONO D500/1 1 X 125 1 X 200 1 X 250 D1000/1 1 X 175 1 X 275 1 X 500 D2000/1 1 X 375 1 X 600 1 X 1000 D3000/1 1 X 500 1 X 1000 1 X 1500 General Specifications Con v ersion Efficiency >80% @4 ohms F requency Response 20Hz - 200Hz +0, -1dB T otal Har monic Distor tion <0.
5 Fuse Requirements Y ou will need to install an in-line fuse or circuit break er in the pow er wire within 18” of the batter y . This fuse or circuit break er is to protect y our v ehicle from fire in case the po wer wire shor ts to the v ehicle body .
AMPLIFIER ST A TUS LEDS The LEDs provide the f ollowing indications: 1. P ower - These LEDs illuminates the center Precision P o wer logo bac kground when the amplifier po wer is turned on. 2. Shor t - These LEDs behind the PPI logo will flash to indicate a shor t on the output.
T OOLS/P ARTS FOR INST ALLA TION NO TE: T OOLS ARE NO T SUPPLIED . Small flat b lade scre wdriver Phillips scre wdriver (#2 or medium siz ed) Wire cutters Wire strippers 4 - #6 round head scre ws, and 1 - #8 sheet metal scre w .
Note: The cables running from the battery to the rear of the car should be installed on the side of the car opposite to the antenna. When using 16 gauge wire or larger , run the speaker wires from the amplifier location through the v ehicle to the speak ers .
Note: The amplifier comes with the connector inser ted into the amplifier with the wire c lamping screws in the up position as shown belo w . Use a 2mm hex head wrenc h to secure the wires to the connector . If the connector needs to be unplug ged from the amplifier , use a 2.
wires as close together as possib le, and use the same gauge wire f or both. This will ensure that y ou ha v e a good g round path, and ma y eliminate such potential prob lems as engine noise and ov erheated amplifiers.
1300W = 108 Amps total current dra w 12V If the same amplifier is driven into a 2 ohm load, doub le it’ s 4 ohm RMS rating. These amplifiers will eff ectively doub le their po w er at this load.
PO WER LOCK CONNECT ORS Once y ou ha v e run both the power and g round wires , then connect the cab les to the amplifier . Cut off e xcess wire, and using wire strippers, strip the ends of the power and g round cab les appro ximately 1/4 inch. Locate the Po w e r Loc k TM pow er and ground connector (supplied).
FR ONT PLA TE DIA GRAMS 1. Cooling Plenums: Maintain a minim um 2” clearance around cooling plenums f or proper amplifier cooling. 2. Speaker/Remote Connector: The P ower Loc k TM speak er connector . 3. Output Freq. Control: Use this control to adjust the sub bass output signal crossov er frequency from 30Hz to 4kHz.
12. -12dB Input Atten uation: Push this s witch ‘IN’ f or high voltage (4V -12V) capability . This button pushed ‘IN’ must be used f or speak er le v el input on common ground head-units or f or high v oltage line drivers . 13. Phase: These s witch sets the phase of the output relativ e to the amplifier input.
4. Cooling Plen ums: Maintain a minimum 2” clearance around cooling plenums f or proper amplifier cooling. INPUTS There are two sets of RCA jac ks on the front end of y our amplifier . The RCA cab les from y our source unit go in the set labeled INPUTS .
QB ASS PLUS SPECIFICA TIONS QB ASS PLUS TM Up to 18dB of boost with selectab le center frequency at 30Hz, 36Hz, 44Hz or 60Hz, with a Q-f actor of 2. Optional QB ASS REMO TE TM This boost control can be mounted in the dash and will supersede the boost control on the amplifier endplate.
QB ASS PLUS/QB ASS REMO TE On these amplifiers, w e’v e tak en bass control to a higher le vel with QB ASS PLUS TM . The two QB ASS TM s witches (labeled 1 and 2) on the front end of the amplifier allow y ou to select one of four frequency centers 30Hz, 36Hz, 44Hz and 60Hz.
TC-X CR OSSO VER Y our ne w amplifier has a TC-X Crossov er (T otal Control X-ov er ® ) 30Hz-4kHz (see this guide f or Crosso v er Char t).12dB per octa v e phase correlated crossov er built-in to pro vide superior system fle xibility without the added e xpense and installation of an outboard crossov er .
CR OSSO VER DETENT CHART Detent # Low P ass F requency (Hz) @ -3dB High P ass F requency (Hz) @ -3dB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 .
ADJUSTING INPUT GAIN 1. Adjust all amplifier input gain controls to just abov e minimum sensitivity (fully countercloc kwise). 2. Using the cleanest music source (CD) pla ying, tur n up the head unit source v olume until y ou can hear distor tion. No w tur n it do wn a bit until y ou cannot hear the distor tion (usually just below full v olume).
NO SOUND Is the LED illuminated? YES NO Chec k P ower and Remote tur n-on wire f or voltage . Mak e sure the ground wire is secure. STILL NO SOUND See your A uthor iz ed Precision P ower TM Dealer or call 1-800-62PO WER.
LIMITED TW O YEAR CONSUMER W ARRANTY : Directed Electronics promises to the original purchaser , to replace this product should it prov e to be def ective in w orkmanship or mater ial under nor mal us.
Een belangrijk punt na aankoop van elk apparaat Precision Power D2000/1 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Precision Power D2000/1 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Precision Power D2000/1 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Precision Power D2000/1 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Precision Power D2000/1 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Precision Power D2000/1 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Precision Power D2000/1 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Precision Power D2000/1 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
