Gebruiksaanwijzing /service van het product DCX 500.2 van de fabrikant Precision Power
Ga naar pagina of 22
AMPLIFIER MODELS DCX 300.2 DCX 500.2.
T ABLE OF CONTENTS Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Ser vice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Caution . . . . . . . . . . . . . .
CONGRA TULA TIONS Thank you f or choosing Precision P ower TM audio equipment. Designed and engineered in the USA, this product combines innov ativ e technology with the finest materials to consistently deliver Absolutely State of the Ar t ™ perf or mance, sound quality , reliability , and v alue.
FEA TURES New! Advanced Instrumentation Input Stage. New! 24dB/Octav e; HP/LP/FULL; 30-4kHz Crossov er . New! Independent Line Output Crossov er 30-4kHz PWM P ower Supply T r iple Dar lington Output Stage. AP-IV Protection Circuity QB ASS TM Bass Boost High V oltage Input Capability with -12dB Attention Switch.
SPECIFICA TIONS Power Ratings MODEL 4 ohm 2 ohm 4 ohm MONO DCX 300.2 2 X 75 2 X 150 1 X 300 DCX 500.2 2 X 125 2 X 250 1 X 500 All power ratings given abo ve are tested at 12.
5 Fuse Requirements Y ou will need to install an in-line fuse or circuit break er in the power wire within 18” of the batter y . This fuse or circuit breaker is to protect your v ehicle from fire in case the power wire shor ts to the v ehicle body .
AMPLIFIER ST A TUS LEDS The LEDs provide the f ollowing indications: 1. P ower - This LED illuminates RED when the amplifier pow er is tur ned on with the remote input (output muted). After a shor t time dela y this LED will tur n GREEN (amplifier ready).
T OOLS/P ARTS FOR INST ALLA TION NO TE: TOOLS ARE NO T SUPPLIED. Small flat blade scre wdr iv er Phillips screwdriv er (#2 or medium sized) Wire cutters Wire strippers 4 - #6 round head screws , and 1 - #8 sheet metal screw .
Note: The cables running fr om the battery to the rear of the car should be installed on the side of the car opposite to the antenna. When using 16 gauge wire or larger , run the speaker wires from the amplifier location through the v ehicle to the speakers .
Note: The power connector is inserted into the amplifier with the wire clamping scre ws in the up position as shown below . GROUND WIRING Locate an area near the amplifier(s) that is metal and clean an area about the size of a quar ter down to bare metal.
Y ou should also chec k the condition and current capacity of the stock battery negative cab le and connections, and replace or upgrade as necessary . K eep in mind that your amplifiers simply conv er t electr ical energy to acoustical energy , and any electrical deficiency will compromise the perf or mance of y our sound system.
If the same amplifier is driven into a 2 ohm stereo or 4 ohm mono load, double it’ s 4 ohm RMS rating. All DCX amplifiers will eff ectiv ely double their po wer at this load.
PO WER LOCK CONNECT ORS Once you ha ve run both the power and g round wires, then connect the cables to the amplifier . Cut off e xcess wire, and using wire strippers, strip the ends of the power and ground cab les appro ximately 1/4 inch. Locate the Po w e r Lock TM pow er and ground connector (supplied).
DCX 300.2, DCX 500.2 FRONT PLA TE DIA GRAM 1. Cooling Plenums: Maintain a minimum 2” clearance around cooling plenums f or proper amplifier cooling. 2. Speaker/Remote Connector: Plug in the P ower Loc k TM connector here. 3. Output Xover Freq. Control: Use this control to adjust the sub bass output signal crossov er frequency from 30Hz to 4kHz.
DCX 300.2, DCX 500.2 END PLA TE DIA GRAM 1. Cooling Plen ums: Maintain a minim um 2” clearance around cooling plenums f or proper amplifier cooling. 2. P ower/Gr ound Po w e r Lock TM : After you ha ve securely connected your po wer and ground wires, plug in the P ower/Ground Po w e r Lock TM connector here.
INPUTS There are two sets of RCA jac ks on the front end of your amplifier . The RCA cables from y our source unit go in the set labeled INPUTS. If your source unit doesn’t ha ve RCA outputs , then add a set of RCA plugs (av ailable at y our dealer) to your front or rear set of speaker leads (see dr awing belo w).
QB ASS PLUS/QBASS REMO TE On DCX 300.2 , and DCX 500.2 amplifiers, w e’v e taken bass control to a higher le v el with QB ASS PLUS TM . The two QB ASS TM s witches (labeled 1 and 2) on the front end of the amplifier allow y ou to select one of f our frequency centers 30Hz, 36Hz, 44Hz and 60Hz.
TC-X CROSSO VER Y our new DCX amplifier has a TC-X Crossov er (T otal Control X- over ® ) 30Hz-4kHz (see this guide for Crosso ver Chart).12dB per octav e phase correlated crossov er b uilt-in to provide superior system fle xibility without the added e xpense and installation of an outboard crossov er .
CROSSO VER DETENT CHART Detent # Low P ass F requency (Hz) @ -3dB High P ass F requency (Hz) @ -3dB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 3.
ADJUSTING INPUT GAIN 1. Adjust all amplifier input gain controls to just abov e minimum sensitivity (fully counterclockwise). 2. Using the cleanest music source (CD) pla ying, tur n up the head unit source v olume until you can hear distor tion. Now turn it down a bit until you cannot hear the distortion (usually just below full v olume).
TROUBLESHOO TING NO SOUND Is the LED illuminated? YES NO Check P ower and Remote tur n-on wire f or voltage . Make sure the g round wire is secure. STILL NO SOUND See your A uthor ized Precision P ower TM Dealer or call 1-800-62PO WER.
LIMITED TWO YEAR CONSUMER W ARRANTY : Directed Electronics, Inc. promises to the original purchaser , to replace this product should it prov e to be defectiv e in workmanship or mater ial under normal.
Een belangrijk punt na aankoop van elk apparaat Precision Power DCX 500.2 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Precision Power DCX 500.2 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Precision Power DCX 500.2 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Precision Power DCX 500.2 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Precision Power DCX 500.2 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Precision Power DCX 500.2 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Precision Power DCX 500.2 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Precision Power DCX 500.2 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
