Gebruiksaanwijzing /service van het product XL/Pro van de fabrikant Primera Technology
Ga naar pagina of 20
012004-510887-(01) Connectivity Guide © 2004 All rights reserved. Optical Disc Laminator XL/Pro MAX 510887.qxd 1/21/2004 7:35 PM Page i.
Notices : The information in this document is subject to change without notice. NO W ARRANTY OF ANY KIND IS MADE WITH REGARD TO THIS MA TERIAL, INCLUDING, BUT NOT LIMITED TO , THE IMPLIED W ARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A P ARTICULAR PURPOSE.
iii T able of Contents Optical Disc Laminator Guide .....................................................................................1 A. Unpacking and Inspection ...............................................................................1 B. Installing the Laminator Software Driver.
iv Inter activ e F eature in this PDF Document There are interactive features that will allow you to jump to different locations within the document. Each listing in the T able of Content s is interactive. Place the cursor on either the words or the page number .
Optical Disc Laminator Connectivity Guide 1 Optical Disc Laminator Connection Guide THANK Y OU… Thank you for purchasing the Optical Disc Laminator Connectivity Kit. This kit will allow you to use your Optical Disc Laminator in conjunction with the Pro, XL and MA X versions of Optical Disc Duplicators.
2 Optical Disc Laminator Connectivity Guide e. Make certain the Laminator has been plugged into power and turned on. f . Select "Install Softwar e A utomatically" and click Next .
Optical Disc Laminator Connectivity Guide 3 g. Y ou may see a notice like the one shown here stating that the A ccent Disc Laminator has not passed W indows Logo T esting. Click the Install Anyway button to continue installing the printer driver for your Laminator .
4 Optical Disc Laminator Connectivity Guide The following steps describe in detail how to connect the Laminator to your DuplicatorMAX: a. Connect the Laminator Stand to the left hand side of the DuplicatorMAX as shown: b. Remove the Input Bin closest to the Laminator Stand to make room for the Laminator's disc tray .
Optical Disc Laminator Connectivity Guide 5 5) F rom the Main Application Screen click Robotics then Options . 6) Enable the Use Laminator checkbox. 7) Click the button labeled Move to (Calibrate) . This will move the Picker Mechanism to the Laminator T ray position.
6 Optical Disc Laminator Connectivity Guide b) While the LEDs are flashing, press the P ause button. The Picking Mechanism will lower to the Laminator T ray P osition. c) A djust the Laminator T ray for ward and back by loosening the adjusting screws located towards the front of the stand.
Optical Disc Laminator Connectivity Guide 7 f) T ighten the A djusting Screws on the front of the Laminator Stand to lock the stand in position. 9. Y ou have now calibrated your Laminator to the Duplicator MAX and are ready to produce discs! D. CREA TING DISCS WITH Y OUR DUPLICA T OR MAX IN PRIMO Laminating your disc jobs is very simple.
8 Optical Disc Laminator Connectivity Guide The Laminator is positioned at the front left corner of the Duplicator . The optional Duplicator XL/Pro Laminator Stand is needed for both of these configurations.
Optical Disc Laminator Connectivity Guide 9 4. Connect the Laminator Stand to the back of the Laminator as shown: 5. Place the Laminator on the Laminator Stand as shown: There are two sets of holes on the underside of your Laminator . Set the Laminator on the stand locating the smaller set of holes on the metal locating pegs on the Laminator Stand.
10 Optical Disc Laminator Connectivity Guide 6. Connect the A uxiliar y Control Cable and P ower Cable the Laminator as shown: 7. Align the Laminator's tray position to the picker . This is done as follows: a. Make certain the Laminator has power and is turned on.
Optical Disc Laminator Connectivity Guide 11 8. The Laminator is now aligned properly . Once the Laminator's Heat Roller has achieved proper operating temperature (indicated by a solidly lit Ready LED on the Laminator's Control P anel), you are ready to laminate discs.
12 Optical Disc Laminator Connectivity Guide 4. Place the Laminator on the stand. The Laminator will need to be placed on the stand with the Laminator's rubber feet resting in the four holes located on the top of the Stand as shown: 5. Using the provided USB Cable, connect the Laminator to your PC as shown: 6.
Optical Disc Laminator Connectivity Guide 13 c. If the Laminator T ray is not in the OUT position, press the Laminate button to eject the Laminator Disc T ray . d. F rom the Main Application Screen click Robotics then Options. e. Enable the Use Laminator checkbox.
14 Optical Disc Laminator Connectivity Guide 8. F rom the Main Application Screen click Robotics then Options . Select Lamination as shown: 9. Set up your print and record job as you normally would per the Duplicator XL/Pro User's Manual. 10. Click the red circle Record button to start your job! 510887.
Optical Disc Laminator Connectivity Guide 15 F . TR OUBLESHOO TING Problem Resolution W ill not Laminate • Check P ower to the Laminator • Make sure that the Ready LED is on and steady indicating .
Printed in the United States of America P/N 510887 510887.qxd 1/21/2004 7:35 PM Page 16.
Een belangrijk punt na aankoop van elk apparaat Primera Technology XL/Pro (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Primera Technology XL/Pro heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Primera Technology XL/Pro vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Primera Technology XL/Pro leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Primera Technology XL/Pro krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Primera Technology XL/Pro bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Primera Technology XL/Pro kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Primera Technology XL/Pro . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
