Gebruiksaanwijzing /service van het product 100 van de fabrikant PYLE Audio
Ga naar pagina of 17
Router Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence. Model No. ______________________________________ T ype ___________________________________________ Serial No.
2 Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could result in serious injury and pr operty damage.
3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer , birth defects or other reproductive harm.
4 Read all instructions. Failure to follow all instructions listed below may result in electric shock, fir e and/or serious injury . The term "power tool" in all of the war nings listed below refers to your mains-operated (cor ded) power tool or battery-operated (cordless) power tool.
5 d) Remove any adjusting key or wrench befor e tur ning the power tool on. A wrench or a key left attached to a r otating part of the power tool may result in personal injury . e) Do not overreach. Keep pr oper footing and balance at all times. This enables better control of the power tool in unexpected situations.
6 1. HOLD POWER TOOL BY INSULA TED GRIPPING SURF ACES WHEN PERFORMING AN OPERA TION WHERE THE CUTTING TOOL MA Y CONT ACT HIDDEN WIRING OR ITS OWN CORD. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator .
7 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ...................
8 EXTENSION CORD SELECTION If an extension cord is used, make sur e the conductor size is lar ge enough to prevent excessive voltage dr op which will cause loss of power and possible motor damage. A table of recommended extension cor d sizes will be found in this section.
9 FOREWORD The router is one of the most useful tools in the woodworking field. It may be used for many cutting and shaping operations such as slotting, mortising, dadoing, grooving, rabbeting, corner -rounding, beading, dovetailing, veining, inlay work, etc.
10 1. T o remove motor unit from base unit: Open the clamp (A) Fig. 1. While holding base, turn power unit COUNTERCLOCKWISE until lower pin (B) in motor housing is disengaged from gr oove in base. Lift power unit free fr om base unit. 2. Clean and insert shank of bit into collet until shank bottoms, then back it out approximately 1/16".
11 NOTE: Setting the index line to 1/4" on the ring means the cutting edge of the bit is exposed 1/4" below the base. CONNECTING TO POWER SOURCE Before connecting tool to power sour ce AL WA YS MAKE SURE SWITCH IS IN THE “OFF” POSITION. Also check that the power circuit is the same as that shown on specification plate of the router .
12 USING THE ROUTER IMPORT ANT : Before using your router , consider the kind and total amount of material to be removed. Depending on the workpiece, mor e than one cut may be necessary to avoid overloading the motor .
13 TEMPLET GUIDES A wide variety of templet guides is available for use in pattern and templet routing operations. Fig. 7 shows a typical combination bit, templet guide, and locknut. DISCONNECT TOOL FROM POWER SOURCE. T o install, insert templet guide in center hole of router base and secure in place with the locknut.
14 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air . All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.
15 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original purchase.
16 NOTES.
The following are trademarks of PORTER-CABLE • DEL T A (Las siguientes son marcas registradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S.
Een belangrijk punt na aankoop van elk apparaat PYLE Audio 100 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen PYLE Audio 100 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens PYLE Audio 100 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding PYLE Audio 100 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over PYLE Audio 100 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van PYLE Audio 100 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de PYLE Audio 100 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met PYLE Audio 100 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.