Gebruiksaanwijzing /service van het product stand-alone master instrument van de fabrikant Raymarine
Ga naar pagina of 45
Distributed by Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine. The names Raytheon and RTN are owned by the Raytheon Company.
TOP EDGE BLEED MASK FOR 2 COLOUR SEATALK LOGO BIDA T A Operation and Installation ST 3 0.
TOP EDGE BLEED MASK FOR 2 COLOUR SEATALK LOGO Nautech Limited, Anchorage Park, Portsmouth P03 5TD, England Telephone (0705) 693611. Fax (0705) 694642.
ST30 Bidata Operation and Installation Handbook DISPLA Y BIDATA DEPTH SPEED Feet Knots SPEED RESET TM D681 Autohelm and SeaTalk are registered Trade Marks of Nautech Limited Autohelms policy of contin.
ST30 Bidata Operation and Installation Handbook Package Contents The following items are included in the ST30 Bidata package: 1. ST30 Bidata instrument 2. Fixing studs (2 off) 3. Thumb nuts (2 off) 4. Mounting template 5. 1m power cable 6. Depth transducer (through hull) with 10m cable and 1/8in spade connectors 7.
3 ST30 Bidata Operation and Installation Handbook Operation Contents Introduction ....................................................................... 5 Chapter 1: Control Head Installation ................................... 7 1.1 Siting .........
4 ST30 Bidata Operation and Installation Handbook Contents (cont.) 6.2 Speed calibration .......................................................... 31 Units selection Ð speed ................................................. 31 Units selection Ð log .
5 ST30 Bidata Operation and Installation Handbook Intr oduction Designed for above or below deck installation, the ST30 Bidata can be used as a stand-alone master instrument or set to repeat depth and speed information from the SeaTalk bus.
6 ST30 Bidata Operation and Installation Handbook.
Chapter 1: Control Head Installation 7 Chapter 1: Contr ol Head Installation TM B I D ATA D682 110mm (4.33in) 42mm (1.65in) 24mm (1.00in) 56mm (2.20in) 88mm (3.
8 ST30 Bidata Operation and Installation Handbook 1.2 Mounting procedure D682a 24 1 3 5 6 1 Instrument 2 Fixing studs 3 Thumb nuts 4 Sealing gasket 5 Depth transducer cable 6 Speed transducer cable 1. Make sure the surface to which the instrument (1) is to be mounted is smooth and flat.
Chapter 1: Control Head Installation 9 1.3 Power supply (Stand-alone operation) Caution: The ST30 Bidata must be connected to a 12V supply only. – + + + + + SEATALK S P E E D D683 5A Red Screen 12v Supply D E P T H For stand-alone operation, use the standard 1m cable supplied.
10 ST30 Bidata Operation and Installation Handbook 1.5 Connection to adjacent ST30 Instruments The ST30 Bidata is supplied with a daisy-chain cable that allows adjacent ST30 instruments to be linked together. The daisy-chain cable supplies power to adjacent instruments and allows data to be transmitted and received via the SeaTalk bus.
Chapter 2: Transducer Installation 11 Chapter 2: T ransducer Installation 2.1 Connection to instrument The depth and speed transducers are supplied with 10m (32.5ft) of cable. These cables are fitted with female spade connectors that plug directly into the back of the ST30 Bidata instrument.
12 ST30 Bidata Operation and Installation Handbook Depth Speed Speed and depth Caution: Plastic through hull transducers must not be used on vessels with wooden hulls. Note: The ST30 Speed transducers are fitted with standard paddlewheels designed for speeds up to 32 knots.
Chapter 2: Transducer Installation 13 2.3 Paddlewheel replacement If the high speed paddlewheel (supplied) is to be fitted, or the existing paddlewheel to be replaced, proceed as follows: 1. Remove the retaining rings (1) and pin (6) from the speed transducer (3).
14 ST30 Bidata Operation and Installation Handbook 2.4 Installation The depth and speed transducers are supplied with detailed installation and maintenance instructions. These instructions, together with following notes, should be read thoroughly before attempting to install the transducers.
Chapter 2: Transducer Installation 15 Siting of depth transducer (Standard through hull) The depth transducer must be vertical to within 10°, forward, aft and athwart ships.
16 ST30 Bidata Operation and Installation Handbook If any of the following transducers are to be used; • Bronze through hull depth (Z118) • In hull puck (Z117) • Retractable depth (Z120) • Bro.
Chapter 2: Transducer Installation 17 Transducer type Colour coding (cable to unit) Bronze through hull triducer (Z093) Brown & white Ð cut back Red Ð red speed terminal Screen Ð white speed te.
18 ST30 Bidata Operation and Installation Handbook Chapter 3: Fault Finding All Autohelm products are, prior to packing and shipping, subject to comprehensive test and quality assurance programmes.
Chapter 3: Fault Finding 19 Note: After installation, poor performance may be experienced if the surface of the depth transducer has not been 'wetted'. Wetting can take up to 24 hours under normal conditions. The transducer can be wetted prior to launch by applying a mild detergent to the external face.
20 ST30 Bidata Operation and Installation Handbook Chapter 4: Maintenance 4.1 Instrument Atmospheric conditions may cause condensation to appear on the instrument window. This will not harm the instrument and can be cleared by increasing the illumination setting to level 3.
Chapter 5: Operation 21 Chapter 5: Operation The ST30 Bidata is set in the factory to: • display depth in feet • display speed in knots • operate with the depth alarms switched off • operate in Master mode These settings can be changed in calibration (section 6.
22 ST30 Bidata Operation and Installation Handbook • Deep alarm Knots Me tres DEP TH SPEED D710 Deep • Minimum depth Knots Me tres DEP TH SPEED D710 Min • Offset Keel/Waterline Knots Me tres DEP TH SPEED D710 Of fset A further press of Depth will return the unit to current Depth.
Chapter 5: Operation 23 • Log Nm Me tres DEP TH SPEED D710 Log • Maximum Speed Knots Me tres DEP TH SPEED D710 Maximum • Average Speed Knots Me tres DEP TH SPEED D710 Average A further press of Speed will return the unit to current boat speed. Note: Log distances over 999nm or miles are displayed in thousands, hundreds and tens (e.
24 ST30 Bidata Operation and Installation Handbook 5.3 Light Key Cycles the level of instrument illumination. There are 3 levels with level 3 the brightest. TM D719 B I D ATA DEPTH SPEED RE SET Metre s DEPTH SPEED The display returns to current speed after 8 seconds or when speed key is pressed.
Chapter 6: Calibration 25 Chapter 6: Calibration 6.1 Depth calibration The ST30 Bidata can be programmed to display depth information in feet or metres, set alarms for shallow and deep water and allow for keel or waterline offsets. To select the calibration menu, press and hold and Depth .
26 ST30 Bidata Operation and Installation Handbook Units selection – depth 1. Cycle Depth until the display shows feet or metres. TM D686 B I D ATA DEP TH SPEED RESET Feet DEP TH SPEED 2. Select feet or metres, as required, using Reset . TM D687 B I D ATA DEP TH SPEED RESET Metre s DEP TH SPEED Shallow alarm 1.
Chapter 6: Calibration 27 2. Press Reset or to set the required depth. TM D688a B I D ATA DEPTH SPEED RESET Metre s Shallow DEPTH SPEED 3. The Shallow Alarm is enabled by pressing Speed . When the alarm is on the 'Alarm' legend is displayed.
28 ST30 Bidata Operation and Installation Handbook 2. Press Reset or to set the required depth. TM D690a B I D ATA DEPTH SPEED RESET Metre s Deep DEPTH SPEED 3. The 'Deep' alarm is enabled by pressing Speed . When the alarm is on the 'Alarm' legend is displayed.
Chapter 6: Calibration 29 Offset The instrument measures the water depth below the transducer. To display water depth below the keel or to the surface an offset must be set up. A negative offset is used to reduce the displayed value to give water depth below the keel.
30 ST30 Bidata Operation and Installation Handbook 1. Press Depth until 'Offset' is selected. TM D693 B I D ATA DEPTH SPEED RESET Metre s Of fset DEPTH SPEED 2.
Chapter 6: Calibration 31 6.2 Speed calibration The ST30 Bidata can be set to display speed in knots or mph and trip and total distance in nm or miles. The most important speed calibration feature is Log Calibration; this calibrates the transducer paddlewheel to the vessel's hull so that accurate speed/log related information is displayed.
32 ST30 Bidata Operation and Installation Handbook Units selection – log 1. Cycle Speed until the display shows nm or miles. TM D697 B I D ATA DEP TH SPEED RESET NM DEP TH SPEED 2. Press Reset to select nm or miles. TM D698 B I D ATA DEP TH SPEED RESET Miles DEP TH SPEED Exit calibration Press and hold and Depth for 2 seconds.
Chapter 6: Calibration 33 Log calibration The ST30 Bidata should not be used for navigational purposes until the transducer paddlewheel has been calibrated to suit the characteristics of the vessel. This is a simple operation and is carried out as follows: 1.
34 ST30 Bidata Operation and Installation Handbook Enter correction factor (CF) 1. Press and hold and Depth . After 2 seconds the display will show CAL . TM D685 B I D ATA DEP TH SPEED RESET DEP TH SPEED 2. Press Speed 3 times to select 'Log Calibration'.
Chapter 6: Calibration 35 4. To exit calibration and return to 'Speed and Depth' mode, press and hold and Depth for 2 seconds. TM D703 B I D ATA DEPTH SPEED RESET Mph Metre s DEPTH SPEED 6.
36 ST30 Bidata Operation and Installation Handbook 2. Press Speed and Reset momentarily TM D707 B I D ATA DEP TH SPEED RESET DEP TH SPEED 3. Calibration Lock/Unlock is switched on or off using Reset. TM D708 B I D ATA DEPTH SPEED RESET DEPTH SPEED C0 = Calibration Locked, i.
Chapter 6: Calibration 37 6.4 Master/Repeater mode As it leaves the factory, the ST30 Bidata is set to operate in master mode. In this mode the instrument is connected to speed and depth transducers, and transmits data onto the SeaTalk Bus. The Bidata can be set as a repeater, to repeat depth and speed information already on the SeaTalk bus.
38 ST30 Bidata Operation and Installation Handbook 3. Press Reset to change between modes TM D705A B I D ATA DEP TH SPEED RESET DEP TH SPEED 4. To exit calibration, press and hold and Depth for 2 seconds. TM D705B B I D ATA DEPTH SPEED RESET Mph Metre s DEPTH SPEED Note: When the Bidata is set to Repeater mode access to calibration is inhibited.
Chapter 7: Specification 39 Chapter 7: Specification Detailed Specification: Power Consumption: 60mA (normal) 100mA (illuminated) Depth transmitted power: 50W Receiver sensitivity: 0.
40 ST30 Bidata Operation and Installation Handbook Speed: Boat speed: 0 to 99.9 knots or mph (0.1 increments) Trip distance: 0 to 999nm or miles (0.01 increments to 9.99, 0.1 to 99.9 and 1.0 to 999). Log (non resetable): 0 to 5999nm or miles (0.1 increments to 99.
TOP EDGE BLEED MASK FOR 2 COLOUR SEATALK LOGO Nautech Limited, Anchorage Park, Portsmouth P03 5TD, England Telephone (0705) 693611. Fax (0705) 694642.
TOP EDGE BLEED MASK FOR 2 COLOUR SEATALK LOGO Nautech Limited, Anchorage Park, Portsmouth P03 5TD, England Telephone (0705) 693611. Fax (0705) 694642.
Een belangrijk punt na aankoop van elk apparaat Raymarine stand-alone master instrument (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Raymarine stand-alone master instrument heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Raymarine stand-alone master instrument vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Raymarine stand-alone master instrument leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Raymarine stand-alone master instrument krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Raymarine stand-alone master instrument bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Raymarine stand-alone master instrument kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Raymarine stand-alone master instrument . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
