Gebruiksaanwijzing /service van het product Captur (2016) van de fabrikant Renault
Ga naar pagina of 246
R enault C APTUR Driv er s handbook.
A passion for perf or mance ELF , partner of RENAUL T recommends ELF Partners in cutting-edge automotive technology , Elf and Renault combin e their expertise on both the racetrack and the city st reets. This enduring partnership gives drivers a range of lubricants perfectly suited to Renault cars.
0.1 T ranslated from French. Copying or translation, in part or in full, is forbidden unless prior written permission has been obtained from the vehicle manu- facturer .
0.2.
0.3 Getting to know your vehicle ............................... Driving ................................................................... Y our comfort ......................................................... Maintenance ..........................
0.4.
1.1 Section 1: Getting to know your vehicle RENAUL T card: General information, use, deadlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Opening and closing the doors . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 The RENAUL T card is used for: – locking/unlocking the doors and tailgate (doors, tailgate) and the fuel filler flap (see the following pages); – switch on the vehicle lighting remo- tely (refer to the following pages); – starting the engine; refer to the in- formation on “Starting the engine” in Section 2.
1.3 Integrated key 5 The integrated key is used to lock or unlock the front left-hand door if the RENAUL T card does not work: – when the RENAUL T card battery is drained, flat battery , etc. – use of devices using the same fre- quency as the card; – vehicle located in a high electromag- netic radiation zone.
1.4 RENAUL T CARD: general information (3/3) Replacement: need for an additional RENAUL T Card If you lose your RENAUL T card or require another , you can obtain one from an authorised dealer . If a RENAUL T card is replaced, it will be necessary to take the vehi- cle and all of its RENAUL T cards to an approved Dealer to initialise the system.
1.5 Unlocking/locking the luggage compartment only Press button 4 to unlock/lock the lug- gage compartment. RENAUL T card not detected alarm If you open a door while the engine is running and the card is not in the reader , the message “Keycard not de- tected” and a beep will warn you.
1.6 HANDS-FREE RENAUL T CARD: use (1/4) 1 2 4 3 Unlocking the vehicle With the RENAUL T card in zone 1 and the vehicle locked, press button 3 on handle 2 on one of the two front doors: the vehicle will unlock. Pressing button 4 also unlocks all the doors and the tailgate.
1.7 HANDS-FREE RENAUL T CARD: use (2/4) 3 1 The hazard warning lights flash twice and a beep sounds to indicate that the doors have locked. The beep may be switched off.
1.8 HANDS-FREE RENAUL T CARD: use (3/4) 5 Locking using the RENAUL T card With the doors and luggage compart- ment closed, press button 5 : the vehi- cle will lock. The hazard warning lights flash twice to indicate that the doors have locked. Note: the maximum distance at which the vehicle locks depends on the sur- roundings.
1.9 HANDS-FREE RENAUL T CARD: use (4/4) 6 Special features The vehicle will not lock if: – a door or the tailgate is open or not properly closed; – a card is still in zone 6 (or in the card reader) and no other card is in the external detection zone.
1.10 Never use deadlocking if someone is still inside the vehicle. V ehicle with RENAUL T card Press button 2 twice in quick succes- sion. V ehicle with RENAUL T “hands-free” card With the vehicle unlocked, you can also press the button 3 on the driver ’s or passenger ’s side door twice in quick succession.
1.1 1 Opening from the inside Pull handle 4 . Lights-on reminder buzzer If you have switched off the ignition and left the lights switched on, a re- minder buzzer will sound when a door is opened. Opening the doors from the outside With the doors unlocked, pull handle 1 .
1.12 Child safety T o make it impossible for the rear doors to be opened from the inside, move lever 5 on each door and check from the inside that the doors are securely locked.
1.13 Locking the doors manually T urn screw 2 with the door open (using the end of the key) and close the door . This means that the doors are then locked from the outside. The doors may then only be opened from the inside or by using the key in the front left-hand door .
1.14 LOCKING/UNLOCKING THE DOORS (2/2) Door and tailgate status indicator With the ignition on , the warning light integrated in switch 3 informs you of the locking status of the opening elements: – indicator light on, the doors and tail- gate are locked, – indicator light of f, the doors and tail- gate are unlocked.
1.15 Operating principle After the vehicle is started, the system automatically locks the doors when you are driving at approximately 6 mph (10 km/h) and over . The door can be unlocked: – by pressing the button 1 to unlock the doors; – by opening a front door (vehicle sta- tionary).
1.16 FRONT HEADRESTS T o raise the headrest Pull the headrest upwards to the de- sired height. Check that it is correctly locked. T o lower the headrest Press button 1 and guide the headrest down to the desired height. Check that it is correctly locked.
1.17 Heated seats With the ignition on, press the switch 4 for the seat desired. The indicator light in the switch lights up. The system, which has a thermostat, regulates the heating and deactivates it if necessary . T o move the seat forwards or backwards Lift handle 1 to unlock.
1.18 Always wear your seat belt when trav- elling in your vehicle. Y ou must also comply with the legislation of the par- ticular country you are in. SEA T BEL TS (1/3) 1 2 Incorrectly adjusted or twisted seat belts may cause injuries in the event of an accident.
1.19 SEA T BEL TS (2/3) ß Front seat belt reminder warning light This lights up on the central display when the engine is started then, if the driver ’s or front passenger ’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approxi- mately 12 mph (20 km/h), it flashes and a bleep sounds for around 2 minutes.
1.20 SEA T BEL TS (3/3) Check that the rear seat belts are positioned and operating correctly each time the rear bench seat is moved. Rear seat belts 7 The belts are locked, unlocked and adjusted in the same way as the front belts.
1.21 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEA T BEL TS (1/4) 1 – Have the entire restraint system checked following an accident. – No operation whatso- ever is permitted on any part of the system (pretensioners, air bags, computers, wiring) and the system components must not be reused on any other vehicle, even if identical.
1.22 Load limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level.
1.23 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEA T BEL TS (3/4) Operating faults W arning light 4 å will light up on the instrument panel when the ignition is turned on and then go out after a few seconds. If it does not light up when the ignition is switched on, or comes on when the engine is running, there is a fault in the system.
1.24 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEA T BEL TS (4/4) W arnings concerning the driver ’ s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances. – Do not attach any objects (badge, logo, clock, telephone holder , etc.
1.25 METHODS OF RESTRAINT IN ADDITION TO THE REAR SIDE SEA T BEL TS Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. – Have the entire restraint system checked following an accident.
1.26 Side Airbags This airbag may be fitted to each of the front seats and is activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact.
1.27 ADDITIONAL METHODS OF RESTRAINT The airbag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system.
1.28 CHILD SAFETY : General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility .
1.29 CHILD SAFETY : General information (2/2) Using a child seat The level of protection offered by the child seat depends on its ability to re- strain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact.
1.30 CHILD SAFETY : choosing a child seat Rear-facing child seats A baby’s head is, proportionally , heavier than that of an adult and its neck is very fragile. T ransport the child in this po- sition for as long as possible (until the age of 2 at the very least).
1.31 CHILD SAFETY : choosing a child/baby seat mounting (1/2) There are two ways of attaching child seats: via the seat belt or using the ISOFIX system. Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact.
1.32 CHILD SAFETY : choosing a child/baby seat mounting (2/2) The two rings 1 are located between the seatback and the seat base and are identified by a marking. Use the access guides 2 of the child seat to ease it into place and lock it into the rings 1 .
1.33 CHILD SAFETY : fitting a child seat (1/4) Some seats are not suitable for fitting child seats. The diagram on the follow- ing page shows you how to attach a child seat. The types of child seat indicated may not be available. Before using a differ- ent child seat, check with the manufac- turer that it can be fitted.
1.34 CHILD SAFETY : fitting a child seat (2/4) In the rear side seat A carrycot can be installed across the vehicle and will take up at least two seats.
1.35 ³ Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat. CHILD SAFETY : fitting a child seat (3/4) Child seat attached using the belt ¬ Seat which a.
1.36 CHILD SAFETY : fitting a child seat (4/4) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected.
1.37 CHILD SAFETY : deactivating/activating the front passenger air bag (1/3) Deactivating the front passenger airbags (on equipped vehicles) Y ou must deactivate the devices in ad- dition to the front passenger seat belt before fitting a child seat in the front passenger seat.
1.38 3 DANGER Since operation of the front passenger airbag is not compatible with the position of a rear-facing child seat, NEVER fit a restraint system for a rear-fac- ing child in a seat protected by an ACTIV A TED front AIRBAG . This can cause the CHILD’S DEA TH or SERIOUS INJUR Y .
1.39 CHILD SAFETY : deactivating/activating the front passenger air bag (3/3) The passenger airbag must only be deactivated or acti- vated when the vehicle is stationary . If it is interfered with when the ve- hicle is being driven, indicator lights å and © will come on.
1.40 DRIVING POSITION: LEFT -HAND DRIVE (1/2) 1 2 3 4 6 8 11 12 1 14 10 15 21 25 22 17 9 16 20 13 18 19 23 5 7 7 24.
1.41 DRIVING POSITION: LEFT -HAND DRIVE (2/2) 1 Side air vent. 2 Stalk for: – direction indicator lights; – exterior lights; – front fog lights; – rear fog lights. 3 Instrument panel. 4 Driver Airbag and horn location. 5 Multimedia system voice control button.
1.42 DRIVING POSITION: RIGHT -HAND DRIVE (1/2) 1 3 5 8 6 7 9 11 12 13 1 2 14 15 16 23 22 18 19 20 21 24 25 10 4 4 17.
1.43 DRIVING POSITION: RIGHT -HAND DRIVE (2/2) The equipment fitted, described below , DEPENDS ON THE VERSION AND COUNTRY . 1 Side air vent. 2 Passenger Airbag location. 3 Heating or air conditioning con- trols. 4 Centre air vents. 5 Multimedia touch screen.
1.44 W ARNING LIGHTS (1/5) In some cases, the appearance of a warning light is accompanied by a mes- sage. š Side light warning light á Main beam headlight tell- tale k Dipped beam headlight tell- t.
1.45 W ARNING LIGHTS (2/5) ® STOP light This lights up when the ignition is switched on and goes out as soon as the engine is started. It comes on with other warning lights and/or messages, and is accompanied by a beep. It requires you to stop immediately , for your own safety , as soon as traffic con- ditions allow .
1.46 x Anti-lock braking warning light This lights up when the ignition is switched on and goes out after a few seconds. If it lights up when you are driving, it in- dicates a fault in the anti-lock braking system. Braking will then be as normal, without the ABS.
1.47 W ARNING LIGHTS (4/5) É Preheating warning light (diesel version) This should come on when the igni- tion is switched on. It indicates that the heater plugs are in operation.
1.48 W ARNING LIGHTS (5/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTR Y . On display B Passenger airbag ON Please refer to the information on “Child safety: deactivating/activating the front passenger airbag” in Section 1.
1.49 DISPLA YS AND INDICA TORS (1/2) Rev counter 1 (graduations x 1000) Driving style indicator 3 Please refer to the information on “Eco- driving” in Section 2. Low engine oil level warning When the engine is started, display 2 alerts the driver when the oil level is at its minimum.
1.50 Speedometer 5 (km or miles per hour) Overspeed buzzer Depending on the vehicle, a warning beep sounds for approximately 10 sec- onds every 30 seconds, as long as the vehicle is travelling in excess of 75 mph (120 km/h). 8 9 6 6 T o return to the previous mode, repeat the same operation.
1.51 ON-BOARD COMPUTER: general information (1/2) On-board computer 1 Depending on the vehicle, this includes the following functions: – distance travelled; – journey settings; – information mes.
1.52 ON-BOARD COMPUTER: general information (2/2) Resetting the trip mileage With “trip mileage recorder” selected on the display , press button 2 or 3 until the mileage recorder resets to zero.
1.53 TRIP COMPUTER: trip settings (1/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTR Y . Examples of selections Interpreting the display selected 101778 km a) T otal mileage and trip mileage recorder . 1 12.4 km FUEL USED b) Journey parameters.
1.54 TRIP COMPUTER: trip settings (2/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTR Y . Examples of selections Interpreting the display selected RANGE e) Estimated range with remaining fuel. The value is displayed after driving 400 metres.
1.55 TRIP COMPUTER: trip settings (3/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTR Y . Examples of selections Interpreting the display selected On-board computer with mileage- before-service message h) Mileage before service or oil change.
1.56 TRIP COMPUTER: trip settings (4/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTR Y . Examples of selections Interpreting the display selected On-board computer with distance before next service message (cntd.) h) Mileage before service or oil change.
1.57 TRIP COMPUTER: trip settings (5/5) Examples of selections Interpreting the display selected i) Reset the tyre pressure. Please refer to the information on the “T yre pressure loss warning” in Section 2. TIRES SET TPW LEARNING THE TYRE PRESSURE SPEED LIMITER CRUISE CONTROL j) Cruise control/speed limiter programmed speed.
1.58 TRIP COMPUTER AND W ARNING SYSTEM: information messages Examples of messages Interpreting the display selected « P ARKING BRAKE ON » Indicates that the parking brake has been applied. « PLEASE REMOVE KEYCARD » Request to remove the RENAUL T card from the reader when you leave the vehicle.
1.59 TRIP COMPUTER AND W ARNING SYSTEM: operating fault messages These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.
1.60 TRIP COMPUTER AND W ARNING SYSTEM: warning message These appear with the ® warning light and require you to stop immediately , for your own safety , as soon as traf- fic conditions allow . Stop your engine and do not restart it. Contact an approved Dealer .
1.61 Power Assisted Steering Never drive with an inadequately charged battery . V ariable power assisted steering The variable power assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed.
1.62 W ait a few seconds, the minutes will flash: repeatedly press or press and hold button 3 or 4 to set the time. When setting is complete, the hours and minutes remain displayed conti- nuously for 2 seconds: your setting is registered. Y ou may change the display .
1.63 Display B V ehicles fitted with touch-screen multimedia, navigation aid systems, telephones, etc. Refer to the separate instructions for the function to understand the special features of this equipment.
1.64 Heated door mirrors With the engine running, mirror de- icing is activated simultaneously with rear screen de-icing/demisting. Folding door mirrors (depending on vehicle) Move button 1 to position F : the door mirrors fold away . T o reset them for driving, return to position C , D or E .
1.65 Daytime running lights function The daytime running lights come on automatically with no action on stalk 1 when the engine is started, and they go off once the engine is switched of f. EXTERIOR LIGHTING AND SIGNALS (1/3) š Side lights T urn the ring 2 until the symbol is opposite mark 3 .
1.66 EXTERIOR LIGHTING AND SIGNALS (2/3) Switching off the lights There are two possibilities: – manually , move ring 2 to position 0 ; – the lights will go out automatically when the engine is switched off, the driver ’s door is opened or the vehicle is locked.
1.67 EXTERIOR LIGHTING AND SIGNALS (3/3) f Rear fog light T urn the centre ring 4 on the stalk until the symbol is opposite mark 5 , then release it. Depending on the vehicle, the stalk re- turns to the initial position or stays in position.
1.68 é Hazard warning lights Press switch 2 . This switch activates all four direction indicators and the side indicator lights simultaneously . It must only be used in an emergency to warn drivers o.
1.69 HEADLIGHT BEAM ADJUSTMENT (1/2) On vehicles fitted with this function, control A allows you to adjust the height of the beams according to the load.
1.70 HEADLIGHT BEAM ADJUSTMENT (2/2) T emporary adjustment Open the bonnet and identify the mark- ing B next to one of the front headlight projectors. For each headlight, using a screw- driver , turn the screw 1 by a quarter turn towards the - symbol to lower the beams.
1.71 Special note When driving, the wiping speed slows down whenever the vehicle stops. For example: the speed will change from a fast wiping speed to normal wiping speed. As soon as the vehicle moves off, wiping will return to the speed originally selected.
1.72 Before any action involving the windscreen (washing the vehicle, de-icing, cleaning the windscreen, etc.) return stalk 1 to position A (park). Risk of injury and/or damage. Windscreen washer With the ignition on, pull stalk 1 to- wards you. A brief pull will trigger a single sweep of the wipers, in addition to the winds- creen washer .
1.73 p Rear screen wash/wipe With ignition on, turn the end of the stalk 1 to bring the mark 2 in line with the symbol. When the stalk is re- leased, it returns to the rear windscreen wiper position.
1.74 FUEL T ANK (1/3) A B 2 1 Fuel grade Use a high-grade fuel that complies with the legislation in force in each country and which must comply with the specifications given on the label on the cover A . Please refer to the in- formation on “Engine specifications” in Section 6.
1.75 FUEL T ANK (2/3) 3 Filling with fuel With the ignition off, insert the nozzle and insert it fully before turning it on to fill the fuel tank (risk of splashing).
1.76 FUEL T ANK (3/3) 4 3 No modifications what- soever are permitted on any part of the fuel supply system (electronic units, wiring, fuel circuit, injectors, pro- tective covers, etc.) as this may be dangerous (unless undertaken by qualified Network personnel).
2.1 Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 Starting/stopping the engine .
2.2 RUNNING IN Petrol version For the first 600 miles (1,000 km), do not exceed 78 mph (130 km/h) in the highest gear , or 3,000 to 3,500 rpm. Y ou may only expect top performance from your vehicle after approximately 1,800 miles (3,000 km) . Service intervals: refer to the Maintenance Document for your vehi- cle.
2.3 Hands-free RENAUL T card The RENAUL T card must be inserted in card reader 2 or in detection zone 3 . T o start, depress the brake or clutch pedal and press button 1 . If a gear is engaged, the vehicle may only be star- ted by depressing the clutch pedal.
2.4 Operating faults In certain cases, the hands-free RENAUL T card may not work: – when the RENAUL T card battery is drained, flat battery , etc. – near to appliances operating on the same frequency as the card (moni- tor , mobile phone, video game, etc.
2.5 Remote control RENAUL T card With the card in reader 2 , press button 1 : the engine will stop. Removing the card from the reader locks the stee- ring column.
2.6 FUNCTION STOP AND ST ART (1/4) This system enables a reduced fuel consumption and lower greenhouse gas emissions. The system is acti- vated automatically when the vehicle is started. While driving, the system stops the engine (standby) when the vehicle is at a standstill (traffic jam, traf fic lights, etc).
2.7 FUNCTION STOP AND ST ART (2/4) T o fill up with fuel, the engine must be stopped (and not on standby): always stop the engine by pressing the engine stop button (please see “Starting, stopping the engine)”.
2.8 FUNCTION STOP AND ST ART (3/4) Conditions preventing the standby of the engine Certain conditions prevent the system from using the engine standby function, including when: – reverse gear is eng.
2.9 Special feature of the automatic engine re-start Under certain conditions, the engine can restart on its own in order to guar- antee your safety and comfort.
2.10 SPECIAL FEA TURES OF PETROL VERSIONS The following operating conditions: – driving for long periods when the low fuel level warning light is lit; – using leaded petrol; – using fuel or lubrication additives which are not approved.
2.1 1 SPECIAL FEA TURES OF DIESEL VERSIONS Diesel engine speed Diesel engines are fitted with an injec- tion pump which prevents the engine speed being exceeded irrespective of the gear selected. If the message “Check antipollution system” is displayed along with warn- ing lights Ä and © , consult an authorised dealer immediately .
2.12 Gear lever Selecting reverse gear V ehicles with manual gearbox: refer to the grid on the gear lever knob 1 . V ehicles with automatic gear- box: refer to the information on the “Automatic gearbox” in Section 2. The reversing lights will come on as soon as reverse gear is selected with the ignition on.
2.13 DRIVING ADVICE, ECO-DRIVING (1/5) Driving style indicator 2 Informs you about the driving style adopted in real time. Y ou will be notified by the colour of warning light 2 . – Green: measured, economical driv- ing; – Y ellow: opt for a calmer driving style; – Orange: driving too fast.
2.14 DRIVING ADVICE, ECO-DRIVING (2/5) 3 Journey record Once the engine is switched off, you will see “Journey record” displayed on the screen 3 , enabling you to view in- formation relating to your last journey . This indicates: – average fuel consumption; – number of miles/kilometres travelled; – number of miles/kilometres saved.
2.15 DRIVING ADVICE, ECO-DRIVING ( 3/5) ECO mode ECO mode is a function which opti- mises fuel consumption. It acts on all elements which consume fuel (engine power , heating and/or air conditioning, etc). 5 Disabling the function Press switch 4 . The 5 light goes out on the ins- trument panel to confirm deactivation.
2.16 Driving advice, Eco-driving Behaviour – Drive carefully for the first few miles until the engine reaches its normal operating temperature, rather than let it warm up while the vehicle is sta- tionary . – Speed is expensive. – Sporty driving uses a lot of fuel: drive with a light right foot.
2.17 DRIVING ADVICE, ECO-DRIVING (5/5) Advice on use – Favour ECO mode. – Electricity is fuel; switch off all the electrical components which are not really needed. However (safety first), keep your lights on when the visibility is bad (“see and be seen”).
2.18 MAINTENANCE AND ANTIPOLLUTION ADVICE Y our vehicle complies with criteria for recycling and recovering vehicles at the end of their service life which will come into force in 2015. Some parts of your vehicle have there- fore been designed to facilitate future recycling.
2.19 ENVIRONMENT Emissions Y our vehicle has been designed to emit fewer greenhouse gases (CO2) while in use, and therefore to consume less fuel (eg. 140 g/km, equivalent to 5.
2.20 TYRE PRESSURE LOSS W ARNING (1/7) If fitted on the vehicle, this system warns the driver of pressure loss in one or several tyres. A A System identification There are two tyre pressure loss warn- ing systems: – System A : can be seen on the label A in the vehicle.
2.21 TYRE PRESSURE LOSS W ARNING (2/7) Operating conditions The system should be reset with an inflation pressure equal to that given on the tyre inflation pressure label. Otherwise it risks not giving a reliable warning in the event of a significant loss of pressure.
2.22 SYSTEM A (cntd.) Resetting the standard level for the tyre pressures This should be done: – after each reinflation or readjustment of the pressure of one of the tyres; – when the standard tyre pressure needs to be changed to adapt to usage conditions (empty , carrying a load, motorway driving, etc.
2.23 TYRE PRESSURE LOSS W ARNING (4/7) SYSTEM A (cntd.) “RECALIBRA TE SET TPW ” The warning light flashes for several seconds, then stays on, along with the message “RECALIBRA TE SET TPW”. They indicate that the request to reset the reference value of the tyre pres- sures must be restarted.
2.24 TYRE PRESSURE LOSS W ARNING (5/7) SYSTEM B Operating principle Each wheel (except for the emergency spare wheel) has a sensor in the infla- tion valve which periodically measures the tyre pressure while driving. W arning light 1 comes on to alert the driver in the event of insuffi- cient pressure (deflated wheel, punctu- red tyre, etc.
2.25 TYRE PRESSURE LOSS W ARNING (6/7) 2 3 4 Reinitialisation is carried out after a few minutes’ driving. Note: The standard tyre pressure cannot be less than that recommended and indi- cated on the door frame. Display The display 2 on the instrument panel informs you of any tyre pressure faults (flat tyre, punctured tyre, etc.
2.26 TYRE PRESSURE LOSS W ARNING (7/7) SYSTEM B (cntd.) “CHECK TYRE PRESSURE SENSORS” The warning light flashes for several seconds, then stays on, along with the message “CHECK TYRE PRESSURE SENSORS”. This message is accompanied by the warning light © .
2.27 DRIVING CORRECTION DEVICES AND AIDS (1/5) Operating faults: – © and x lit up on the in- strument panel alongside messages “CHECK ABS”, “CHECK BRAKING SYSTEM” and “Check ESC”: ABS, ESC and emergency brake assist are deactivated.
2.28 DRIVING CORRECTION DEVICES AND AIDS (2/5) Electronic stability program (ESC) with understeer control and traction control Electronic stability control ESC This system helps you to keep control of the vehicle in critical driving condi- tions (avoiding an obstacle, loss of grip on a bend, etc.
2.29 DRIVING CORRECTION DEVICES AND AIDS (3/5) Emergency brake assist This system supplements the ABS and helps reduce vehicle stopping dis- tances. Operating principle The system allows an emergency brak- ing situation to be detected when the brake pedal is pressed.
2.30 Grip control If fitted on the vehicle, grip control makes it easier to control the vehicle on low grip surfaces (soft ground, etc.). T yres When they need to be re- placed, only tyres of the same make, size, type and profile should be used.
2.31 DRIVING CORRECTION DEVICES AND AIDS (5/5) Hill start assistance Depending on the gradient of the in- cline, this system assists the driver when starting on a hill.
2.32 Switching on Press the side switch 1 . Indicator light 6 comes on, lit orange, and the message “SPEED LIMITER” appears on the instrument panel, accompanied by dashes to indicate that the speed limiter function is activated and waiting to store a limited speed.
2.33 Exceeding the limit speed It is possible to exceed the limit speed at any time. T o do this: press the accel- erator pedal firmly and fully (beyond the resistance point). If the speed is exceeded, the limited speed flashes on the instrument panel accompanied by a beep.
2.34 CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3) Recalling the limit speed If a speed has been saved, it can be re- called by pressing switch 4 ((R)). Putting the function on standby The speed limiter function is suspended when you press switch 5 (O).
2.35 The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 20 mph (30 km/h). This function is an addi- tional driving aid. However , the function does not take the place of the driver .
2.36 Driving Once a cruising speed is stored and the cruise control function is active, you may lift your foot off the accelera- tor pedal. Important: you are never- theless advised to keep your feet close to the pedals in order to react if neces- sary .
2.37 CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While it is being exceeded, the cruising speed flashes on the in- strument panel.
2.38 Switching off the function The cruise control function is deacti- vated if you press switch 1 : in this case a speed is no longer stored. The two in- strument panel warning lights and go out to confirm that the function is deactivated.
2.39 Operating principle Ultrasonic detectors, installed in the rear bumper (depending on the vehi- cle), measure the distance between the vehicle and an obstacle whilst revers- ing.
2.40 Deactivating the system Press switch 2 to deactivate the system. The indicator light built into the switch lights up to remind you that the system is deactivated. Pressing the switch again will react- ivate the system and switch off the in- dicator light.
2.41 REVERSING CAMERA (1/2) 2 1 Note: – ensure that the reversing camera is not obscured (dirt, mud, snow , etc.); – depending on the vehicle, certain settings can be adjusted from the touch screen 2 .
2.42 REVERSING CAMERA (2/2) The screen shows a reverse image. The frames are a representation projected onto flat ground; this in- formation must not be taken into account when superimposed on a vertical object or an object on the ground. Objects which appear on the edge of the screen may be deformed.
2.43 AUTOMA TIC TRANSMISSION (1/3) Operation With the selection lever 1 in position P , switch on the ignition. T o move out of position P , you must de- press the brake pedal before pressing the unlocking button 2 . With the foot on the brake pedal (the warning light 3 on the display goes out), move the lever out of position P .
2.44 AUTOMA TIC TRANSMISSION (2/3) Special cases In certain driving conditions (for exam- ple, engine protection, operation of the Electronic Stability Programme: the au- tomatic system may change gear auto- matically .
2.45 AUTOMA TIC TRANSMISSION (3/3) Parking the vehicle When the vehicle is stopped, move the lever to position P while keeping your foot on the brake pedal: the gearbox is in neutral and the drive wheels are me- chanically locked by the driveshaft. Apply the handbrake .
2.46.
3.1 Section 3: Y our comfort Air V ents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 Manual air conditioning/heating system . . . . . . . . . . . . . . .
3.2 AIR VENTS, air outlets (1/2) 3 8 5 6 1 2 7 1 Left-hand side window demister outlet. 2 Left-hand air vent. 3 Windscreen demisting vents. 4 Centre air vents. 5 Right-hand air vent. 6 Right-hand side window demister outlet. 7 Passenger footwell heater out- lets.
3.3 Side air vents Air flow T o open air vent 11 , press on the air vent (point 12 ) until it is open as far as required. Direction T o direct the air flow , swivel side air vent 11 . Centre air vents. Air flow Move the control knob 10 (beyond the resistance point).
3.4 Switching air conditioning on or off (depending on vehicle) The air conditioning is switched on (in- dicator light on) or off (indicator light of f) using button 3 . Activation is not possible if control 2 is set to OFF . The controls 1 Adjusting the air temperature.
3.5 Air recirculation is for: – isolating the vehicle from the exter- nal atmosphere (driving in polluted areas, etc.); – lowering the passenger compart- ment temperature as quickly as pos- sible. Switching the air recirculation on Press button 6 : the integrated indicator light comes on.
3.6 Adjusting the ventilation speed Move control 2 . The further the control is positioned to the right, the greater the amount of air blown into the passenger compartment.
3.7 V arying the ventilation speed In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. Y ou can still adjust the ventilation speed by turning control 6 to increase or reduce the ventilation speed.
3.8 Clear View function Press button 3 – the integrated indica- tor light comes on. This function quickly demists and de- ices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-ic- ing functions must be activated.
3.9 Rear screen de-icing/ demisting Press button 8 – the integrated indica- tor light comes on. This function en- ables rapid demisting or de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles). T o exit this function, press button 8 again.
3.10 AUTOMA TIC CLIMA TE CONTROL (4/4) 7 6 Air recirculation (isolation of the passenger compartment) K This function is managed automatically (operation is confirmed by a warning light on button 7 ), but you can also acti- vate it manually .
3.1 1 Operating faults As a general rule, contact your ap- proved dealer in the event of an oper- ating fault. – Reduction in de-icing, demisting or air conditioning performance. This may be caused by the passen- ger compartment filter cartridge be- coming clogged.
3.12 ELECTRIC WINDOWS (1/2) 1 2 3 4 5 6 From the driver ’s seat, use switch: 1 for the driver ’s side; 2 for the front passenger side; 3 and 5 for the rear passenger win- dows. From the passenger seats, use switch 6 . Avoid resting any objects against a half-open window: there is a risk that the electric window could be damaged.
3.13 One-touch mode Depending on the vehicle, this mode works in addition to the operation of the electric windows described previously . It is only fitted to the driver ’s window . Briefly press or pull switch 1 fully: the window is fully lowered or raised.
3.14 Unlocking and opening the doors or tailgate switches on the timed cour- tesy lights and lights. Soft lighting 4 It comes on: – on opening the storage drawer; – on opening one of the doors. This switches off after a time delay , once the doors concerned have been closed correctly; – at the same time as the side lights come on.
3.15 Sun visor storage 2 This can be used for storing motorway tickets, cards, etc. Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use. Front door storage pockets 1 They can hold a 1.
3.16 Passenger storage drawer T o open, press the button 7 to unlock the drawer and pull the handle 6 . P ASSENGER COMP ARTMENT STORAGE, FITTINGS (2/5) Maximum load allowed in the pas- senger storage compartment: 6 kg, evenly distributed. Glovebox T o open the glovebox, lift catch 8 .
3.17 P ASSENGER COMP ARTMENT STORAGE, FITTINGS (3/5) When turning corners, accelerating or braking, ensure that the recepta- cle being held by the cup holder is not dislodged.
3.18 Rear door storage compartment 14 They can hold a 0.5-litre bottle. 14 P ASSENGER COMP ARTMENT STORAGE, FITTINGS (4/5) 12 Rear centre console storage compartment 12 This can be used for storing a mobile ashtray , cup holder , etc.
3.19 Grab handle 15 This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle. STORAGE, CABIN FITTINGS (5/5)/ SUN VISOR Front sun visor Lower the sun visor 17 on the wind- screen or unclip it and lower it over the side window .
3.20 Cigar lighter 1 With the ignition on, push in the ciga- rette lighter 1 . It will spring back with a click when it is ready . Pull it out to use. After use, replace it without pushing it all the way in. ASHTRA Y , CIGARETTE LIGHTER, ACCESSORIES SOCKET 3 Connect accessories with a maximum power of 120 watts (12 V) only .
3.21 The headrest is a safety component; check that it is fitted and in the correct po- sition. The top of the head- rest should be as close as possible to the top of the head. T o raise the headrest Raise the headrest as far as it will go, then press button A and remove the headrest.
3.22 SLIDING REAR BENCH SEA T (1/2) T o move forwards or backwards T o unlock the seat: – in the rear , lift the two levers 1 simul- taneously; – from the boot, pull the handle 2 . Move the seat forwards or back to the required position. Release lever 1 or handle 2 and make sure that the seat is locked correctly in position.
3.23 B T o fold down the seatback Ensure that the front seats are far enough forward. Lower the headrests fully . Place the seat belts in their guides A . Lift the handle 3 and lower the seat- back B . Before moving the seatback, put the seat belt in belt guide A to avoid damaging it.
3.24 Opening the doors manually from the inside If it is impossible to unlock the tailgate, it can be done manually from inside: – access the luggage compartment by tilting the rear bench seatback(s), – insert a pencil or similar object in recess 3 and slide the unit as shown in the illustration; – push the tailgate to open it.
3.25 – lift one side of the parcel shelf; – pull the parcel shelf towards you (movement B ), beginning with the part most raised. T o refit, proceed in the reverse order to removal.
3.26 BOOT FITTINGS (1/2) 1 Mobile floor 1 Depending on the vehicle, the mobile floor is reversible. Flat position It allows you to have a flat floor by fold- ing down the back of the rear bench- seat and to compartmentalise the boot into two distinct spaces.
3.27 BOOT FITTINGS (2/2) Hook 4 Y ou can use this to secure a bag. Anchorage points Attachment points 5 If your vehicle is not equipped with anchorage points, you can get them from an authorised dealer .
3.28 Always position the heavi- est items directly on the floor . Use the lashing points 1 on the boot floor , if these are fitted to the vehicle. The luggage should be loaded in such a way that no items will be thrown for- ward and strike the occupants if the driver has to brake suddenly .
3.29 Permissible nose weight, maxi- mum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. Choice and fitting of towing equipment Maximum weight of towing equip- ment: 15 kg For fitting and conditions of use, refer to the equipment’s fitting in- structions.
3.30 Spoiler A Accessing the mounting points Open the doors to access the mount- ing points 1 . For information on the range of equipment adapted to your vehi- cle, we advise you to consult an ap- proved Dealer . Refer to the manufacturer ’s instruc- tions for information on how to fit and use the roof rack bar .
3.31 The presence and location of this equip- ment depends on the vehicle version. 1 Multimedia touchscreen; 2 Multimedia sockets; 3 Steering column control; 4 V oice commands; 5 Microphone. Refer to the equipment instructions for information on how to operate this equipment.
3.32.
4.1 Section 4: Maintenance Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 Engine oil level: general information . . . . . . . . . . . . . . . .
4.2 T o open the bonnet, pull the handle 1 . BONNET (1/2) 1 The engine may be hot when carrying out opera- tions in close proximity . In addition, the engine cooling fan can come on at any moment. Risk of injury . Unlocking the bonnet catch T o open, push tab 2 to the left as you open the bonnet.
4.3 BONNET (2/2) Closing the bonnet Check that nothing has been left in the engine compartment. T o close the bonnet again, hold the bonnet in the middle and lower it to 30 cm above the closed position, then release it. It will latch automatically under its own weight.
4.4 – remove the dipstick and wipe with a clean, lint-free cloth; – push the dipstick in as far as it will go (for vehicles equipped with a cap- type dipstick C , screw the cap in as far as it will go); – take out the dipstick again; – read the level: it should never fall below minimum mark A or exceed maximum mark B .
4.5 T opping up/filling The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is started up for the first time in the day). – Unscrew cap 1 ; – top up the level (as a guide, the ca- pacity between the minimum and maximum reading on the dipstick 2 is between 1.
4.6 Engine oil grade Refer to the Maintenance Service Booklet for your vehicle. ENGINE OIL LEVEL: topping up, filling (2/2) OIL CHANGE Never run the engine in an enclosed space as exhaust gases are poisonous. Engine oil change : if you are changing the oil when the engine is hot, be careful not to scald yourself if the oil overflows.
4.7 Frequency of checking coolant level Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant).
4.8 Level 2 It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “ MINI " warn- ing line. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking pro- cedure from the manufacturer ’s net- work or web site.
4.9 Filters The replacement of filter components (air filter , cabin filter , diesel filter , etc.) is scheduled in the maintenance opera- tions for your vehicle. Replacement intervals for filter el- ements: refer to the Maintenance Document for your vehicle.
4.10 TYRE PRESSURE (1/2) Label A Open the driver ’s door to read it. T yre pressures should be checked when the tyres are cold. If the tyre pressures cannot be checked when the tyres are cold , increase the pressures from 0.2 to 0.3 bar (or 3 PSI ).
4.1 1 TYRE PRESSURES (2/2) Special note concerning fully laden vehicles (Maximum Permissible All-Up Weight) and towing a trailer: the maxi- mum speed must be limited to 60 mph (100 km/h) and the tyre pressure in- creased by 0.2 bar . Please refer to the information on “Weights” in Section 6.
4.12 Label A Observe the indications on the battery: – 2 naked flames and smoking are for- bidden; – 3 eye protection required; – 4 keep away from children; – 5 explosive materials; – 6 refer to the handbook; – 7 corrosive materials.
4.13 BODYWORK MAINTENANCE (1/2) Y ou should W ash your car frequently , with the engine off , with cleaning products rec- ommended by the manufacturer (never use abrasive products).
4.14 Respect local regulations about wash- ing vehicles (e.g. do not wash your ve- hicle on a public highway). Observe the vehicle stopping distances when driving on gravelled surfaces to prevent paint damage. Repair , or have repaired quickly , areas where the paint has been damaged, to prevent corrosion spreading.
4.15 Glass instrument panel (e.g.: instrument panel, clock, exterior temperature display , radio display , mul- timedia or multifunction display etc.) Use a soft cloth (or cotton wool).
4.16 Y ou are strongly recom- mended not to use high- pressure or spray cleaning equipment inside the pas- senger compartment: use of such equipment could impair the correct functioning of the electrical or elec- tronic components in the vehicle, or have other detrimental effects.
4.17 SEA T COVERINGS (1/5) Depending on the vehicle, it is possible to remove the seat covers (cleaning, customisation, etc.). Principle of seat cover removal Whether it’s for the back or the base, always remove as shown in the pic- ture above A : do not rip the self-grip bands out.
4.18 4 SEA T COVERINGS (2/5) For safety reasons, carry out these operations when the vehicle is stationary . 6 Removing the base cover – Open the zip fastener 4 of the base; – remove the cover according to the method shown (movement A ).
4.19 Rear bench seat – Bring the front seats forward; – reinsert the headrest for the rear bench seat; – disengage the seat belts. When moving the rear seats, ensure that nothing obstructs the anchorage points (passenger ’s arm or leg, a pet, gravel, cloth, toys, etc.
4.20 SEA T COVERINGS (4/5) Removing the seatback cover C – fold down the seatback C to the base using the stalk 11 ; – remove the self-grip bands 15 be- tween the seatback and the base; – reinse.
4.21 Replacing the seatback cover D – Position the cover on the seat- back D ; – close the zip fastener 20 ; – attach the self-grip bands 19 ; – slide the lower cover between the seatback D an.
4.22.
5.1 Section 5: Practical advice Puncture, emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 T yre inflation kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2 In case of puncture Depending on the vehicle, a tyre infla- tion kit or emergency spare wheel is provided (refer to the following pages). V ehicle fitted with a tyre pressure loss warning system If under-inflated (puncture, low pres- sure, etc.), the warning light on the instrument panel comes on.
5.3 TYRE PRESSURE KIT (1/3) The kit is only approved for inflating the tyres of the ve- hicle originally equipped with the kit. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.
5.4 TYRE PRESSURE KIT (2/3) Depending on the vehicle, in the event of a puncture, use the kit located in the boot or underneath the luggage com- partment carpet. V ehicle fitted with a tyre pressure loss warning system If under-inflated (puncture, low pres- sure, etc.
5.5 TYRE PRESSURE KIT (3/3) If a minimum pressure of 1.8 bar is not reached after 15 minutes, repair is not possible; do not drive the ve- hicle but contact an approved dealer .
5.6 Jack 2 Fold it correctly before refitting it in its housing (ensure that the wheelbrace is correctly positioned). Hubcap tool 3 This tool is used to remove the wheel trims. Wheel bolt guide 4 T o finish loosening or starting to tighten the wheel bolts.
5.7 Remove the wheel trim using hubcap tool 1 (located in the tool kit) by en- gaging the hook in the opening near valve 2 . T o refit it, align it with valve 2 . Push the retaining hooks in fully , starting with side A near the valve, followed by B and C , finishing at D opposite the valve.
5.8 Continue to crank the jack so that the baseplate is correctly positioned (it should be underneath the vehicle and aligned with the jack head). T urn it a few times to lift the wheel off the ground. Switch on the hazard warn- ing lights. Keep the vehicle away from traffic and on a level surface where it will not slip.
5.9 If you have a puncture, re- place the wheel as soon as possible. A tyre which has been punc- tured should always be inspected (and repaired, where possible) by a specialist.
5.10 T yre and wheel safety The tyres are the only contact between the vehicle and the road, so it is essen- tial to keep them in good condition. Y ou must make sure that your tyres con- - form to local road traffic regulations.
5.1 1 Pressures should be checked when the tyres are cold; ignore higher pressures which may be reached in hot weather or following a fast journey . If tyre pressures cannot be checked when the tyres are cold , assume an in- crease of 0.2 to 0.3 bar (or 3 PSI ).
5.12 Use in winter Chains For safety reasons, fitting snow chains to the rear axle is strictly for- bidden. Chains cannot be fitted to tyres which are larger than those originally fitted to the vehicle. TYRES (3/3) Snow or Winter tyres We would recommend that these be fitted to all four wheels to ensure that your vehicle retains maximum adhe- sion.
5.13 Direction indicator lights T urn the bulb holder 1 a quarter of a turn and take out the bulb. Bulb type: PY21W . Once the bulb has been replaced, check that it is properly secured. Dipped beam headlight T o change the bulb: – remove cover A ; – disconnect the wiring 5 (black lead); – unclip the spring 2 and remove the bulb.
5.14 Front side light T o change a bulb, remove the cover B . Pull the bulb holder 6 to access the bulb. Bulb type: W5W . The bulbs are under pres- sure and can break when replaced. Risk of injury . FRONT HEADLIGHTS: changing bulbs (2/3) The engine may be hot when carrying out opera- tions in close proximity .
5.15 Daytime running lights 7 Please see an authorised dealer . Front fog lights 8 – Access the bulb holder via the un- derneath of the vehicle; – unclip the flap; – turn the bulb holder a quarter turn. Bulb type: H16LL. T ype of bulb for vehicles fitted with cornering lights: H1 1LL.
5.16 Pull on the outside A of the light and remove the rear light unit. Remove the bulb holder by releasing clip 2 , then clips 3 . Change the bulb. Refit the bulb holder and push the unit in fully until it locks in place. Check that the light is properly locked in position.
5.17 REAR AND SIDE LIGHTS: changing bulbs (2/2) The bulbs are under pres- sure and can break when replaced. Risk of injury . Side indicator lights 10 The wing mirror needs to be removed; consult an authorised dealer .
5.18 Courtesy light Unclip the lens (using a flat-blade screwdriver or similar). Remove the bulb concerned. Bulb type 1 : W5W . INTERIOR LIGHTING: changing bulbs (1/2) The bulbs are under pres- sure and can break when replaced. Risk of injury . 1 Soft lighting 2 Please contact an authorised dealer .
5.19 3 Luggage compartment light Unclip light 3 by pressing the tabs on each side (using a flat-blade screw- driver or similar). Disconnect the light. 4 5 Press tab 4 to release the bulb holder and access bulb 5 . Bulb type: C5W festoon type bulb. The bulbs are under pres- sure and can break when replaced.
5.20 Operating faults If the battery is too weak to ensure cor- rect operation, you can still start (insert the RENAUL T card in the card reader) and lock/unlock the vehicle (refer to the information on "Locking/unlocking the doors" in Section 1).
5.21 Clip 1 Remove the fuse using tweezers 1 , lo- cated at the back of flap A . T o remove the fuse from the tweezers, slide the fuse to the side. It is not advisable to use the free fuse locations. Fuses in passenger compartment A If any electrical component does not work, check the condition of the fuses.
5.22 FUSES (2/3) Allocation of fuses (the presence of certain fuse depends on the vehicle equipment level) 1 8 15 24 2 9 16 25 3 10 17 26 4 11 18 27 5 12 19 28 29 6 13 20 22 30 7 14 21 23 32 31 33 34 .
5.23 Number Allocation 1 Power-assisted steering, heated front seat, radio 2 Injection, daytime running lights 3 Airbag 4 Automatic gearbox 5 Dipped beam headlights 6 Front fog lights, side lights, ma.
5.24 BA TTER Y : breakdown recovery (1/2) T o avoid all risk of sparks: – Ensure that any electrical consumers (courtesy lights, etc.) are switched off before disconnecting or recon- necting the battery . – When charging, stop the charger before connecting or disconnecting the battery .
5.25 BA TTER Y : breakdown recovery (2/2) Depending on the vehicle, unclip the battery cover . Connect the positive cable A to the support on the (+) terminal 1 , then to the (+) terminal 4 of the battery supplying the current.
5.26 Radio location 1 Unclip the blanking cover . The aerial, + and – supply and speaker wire connec- tions are located behind it. Door speakers 2 T o install any equipment, please con- sult an authorised dealer . FITTING A RADIO 1 2 – In all cases, it is very important to follow the manufacturer ’s instruc- tions carefully .
5.27 ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po- sition of the aerial, etc.), make sure it is compatible with your vehicle. Y ou can get advice from an authorised dealer .
5.28 Lower tab 3 , by pressing on either side A . Then push the blade forwards B , to re- lease hook 4 . T o refit T o refit the wiper blade, proceed in re- verse order to removal.
5.29 T o refit T o refit the wiper blade, proceed in re- verse order to removal. Make sure that the blade is correctly locked in position. Rear screen wiper blade 5 – With the ignition off, lift wiper arm 6 ; – release the blade 5 by pulling it.
5.30 TOWING: breakdown recovery (1/2) Before towing, unlock the steering column: with the clutch depressed, engage first gear (lever in position N or R for vehicles with automatic gear- boxes), insert the RENAUL T card in the card reader , then press the engine start button for two seconds .
5.31 TOWING: breakdown recovery (2/2) Only use the front 3 and rear 6 towing points (never use the drive shafts or any other part of the vehicle) These towing points may only be used for towing: never use them for lifting the vehicle directly or indirectly .
5.32 OPERA TING F AUL TS (1/6) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved Dealer as soon as possible. Using the RENAUL T card POSSIBLE CAUSES WHA T TO DO The RENAUL T card does not lock or unlock the doors.
5.33 OPERA TING F AUL TS (2/6) The starter is activated POSSIBLE CAUSES WHA T TO DO The instrument panel indicator lights are weak or fail to light up and the starter does not turn. Battery terminals not tight, battery terminals discon- nected or oxidised.
5.34 OPERA TING F AUL TS (3/6) On the road POSSIBLE CAUSES WHA T TO DO Vibrations. T yres not inflated to correct pres- sures, incorrectly balanced or dam- aged. Check the tyre pressures: if this is not the problem, have them checked by an ap- proved Dealer .
5.35 OPERA TING F AUL TS (4/6) On the road POSSIBLE CAUSES WHA T TO DO Steering becomes heavy . Assistance overheating. Consult an approved dealer . The engine is overheating. The cool- ant temperature indicator is in the warning zone and warning light ® comes on.
5.36 OPERA TING F AUL TS (5/6) Electrical equipment POSSIBLE CAUSES WHA T TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer . Fuse damaged. Replace the fuse, refer to the information on “Fuses”.
5.37 OPERA TING F AUL TS (6/6) Electrical equipment POSSIBLE CAUSES WHA T TO DO T races of condensation in the lights. T races of condensation may be a nat- ural phenomenon caused by varia- tions in temperature. In this case, the traces will disappear slowly once the lights are switched on.
5.38.
6.1 Section 6: T echnical specifications V ehicle identification plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.2 Engine identification plate . . . . . . . . . . . . . . . . . .
6.2 VEHICLE IDENTIFICA TION PLA TES A B The information shown on the ve- hicle identification plate should be quoted on all correspondence or orders. The presence and location of the in- formation depends on the vehicle. V ehicle identification plate A 1 Manufacturer name.
6.3 Please quote the information on the engine plate or label A in all corre- spondence or orders. (Location varies depending on engine) 1 Engine type.
6.4 1,579* 1,531 0,866 2,606 0,650 4,121 DIMENSIONS (in metres) 1,516 1,957 * unladen.
6.5 ENGINE SPECIFICA TIONS V ersions 0.9 TCe 1.2 TCe 1.5 dCi Engine type (see engine plate) H4B T urbo H5F T urbo K9K T urbo Cubic capacity (cc) 898 1 197 1461 T ype of fuel Octane rating It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap.
6.6 WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’ s equipment. Consult your approved Dealer .
6.7 Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally . If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well.
6.8 Date: Miles (Km): Invoice number: Comments/miscellaneous T ype of operation: Stamp Service □ ....................................... □ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous T ype of operation: Stamp Service □ .
6.9 SERVICE SHEETS (2/6) VIN: .................................................................................. Date: Miles (Km): Invoice number: Comments/miscellaneous T ype of operation: Stamp Service □ .
6.10 SERVICE SHEETS (3/6) VIN: .................................................................................. Date: Miles (Km): Invoice number: Comments/miscellaneous T ype of operation: Stamp Service □ .
6.1 1 SERVICE SHEETS (4/6) VIN: .................................................................................. Date: Miles (Km): Invoice number: Comments/miscellaneous T ype of operation: Stamp Service □ .
6.12 SERVICE SHEETS (5/6) VIN: .................................................................................. Date: Miles (Km): Invoice number: Comments/miscellaneous T ype of operation: Stamp Service □ .
6.13 VIN: .................................................................................. Date: Miles (Km): Invoice number: Comments/miscellaneous T ype of operation: Stamp Service □ .
6.14 ANTICORROSION CHECK (1/5) If the continuation of the warranty is subject to repair , it is indicated below . VIN: ................................
6.15 ANTICORROSION CHECK (2/5) If the continuation of the warranty is subject to repair , it is indicated below . VIN: ................................
6.16 ANTICORROSION CHECK (3/5) If the continuation of the warranty is subject to repair , it is indicated below . VIN: ................................
6.17 ANTICORROSION CHECK (4/5) If the continuation of the warranty is subject to repair , it is indicated below . VIN: ................................
6.18 ANTICORROSION CHECK (5/5) If the continuation of the warranty is subject to repair , it is indicated below . VIN: ................................
7.1 ALPHABETICAL INDEX (1/5) A ABS ..............................................................1.46, 2.27 → 2.31 accessories........................................................................ 5.27 accessories socket ..........................
7.2 ALPHABETICAL INDEX (2/5) driving ........2.2 → 2.5, 2.10 – 2.1 1, 2.13 → 2.17, 2.20 → 2.26, 2.24 → 2.40, 2.43 → 2.45 driving aids ............................................................2.27 → 2.42 driving position settings .....
7.3 ALPHABETICAL INDEX (3/5) horn: flash ............................................................................. 1.68 hubcap tool ................................................................. 5.6 – 5.7 I indicators ........................
7.4 ALPHABETICAL INDEX (4/5) puncture........................................................ 5.2, 5.6, 5.8 – 5.9 R radio................................................................................... 3.31 rear bench seat........................
7.5 ALPHABETICAL INDEX (5/5) transporting objects in the luggage compartment ........................................ 3.28 on the roof ...................................................................... 6.6 trims ...................................
7.6.
.
RENAUL T S. A.S. SOCIÉTÉ P AR ACTIONS SIMPLIFIÉE AU C APIT AL DE 533 941 113 / 13-15, QUAI LE GALLO 92100 BOULOGNE -BILLANCOURT R.C.S. NANTERRE 780 129 987 SIRET 780 129 987 03591 / TÉL.
Een belangrijk punt na aankoop van elk apparaat Renault Captur (2016) (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Renault Captur (2016) heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Renault Captur (2016) vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Renault Captur (2016) leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Renault Captur (2016) krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Renault Captur (2016) bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Renault Captur (2016) kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Renault Captur (2016) . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
