Gebruiksaanwijzing /service van het product H8SX/1668R van de fabrikant Renesas
Ga naar pagina of 44
H8SX/1668R Group E6000H PLQP0144KA -A User System Inte rface Board HS1668RECH61H User’s Manual Renesas M icrocomput er Developm ent Environm ent System H8SX Family / H8SX/ 1600 Ser ies HS1668R ECH61HE REJ10J1867-0200 Revision Date: A pr. 18, 2008 Rev.
.
1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with r.
.
I IMPORTANT INFORMATION READ FIRST • READ this user's ma nual befo re using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to u se the user s ystem in terface board until y ou fully understand its mechanism.
II LIMITED WA RRANTY Renesas warrants its user syst em interfa ce boards to be manufactu red in accordance with published specifications and fr ee from defects in material and/or workmanship. Renesas will repair or replace any user system interfac e boards determined to be defective in ma terial and/or workmanship.
III State Law : Some states do not allo w the exclusion or limitation o f implied warranties or liab ility for incidental or c onsequential damages, s o the above limi tation or excl usion may not appl y to you. This warrant y gives you s pecific l egal rights , and you may have other rights which may va ry from state to state.
IV SAFETY PAGE READ FIRST • READ this user's ma nual befo re using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user s ystem in terface boa rd until you fully underst and its mechanism.
V W ARNING Observe the pr ecautions listed b elow. Failure t o do so will result in a FIRE H AZARD and will damage the us er system and the emul ator product or will r esult in PERSONAL INJURY. The USER PROGRA M will be LOST. 1. Do not repair or remodel the emul ator product by yourself for elect ric shock pre vention and quality assurance.
VI.
i Preface The HS1668RECH61H is a user system interface board that connects a us er system for the H8SX/1668R PLQP0144KA-A (former package: FP-144L) package to the H 8SX/1650 E6000H emulator (HS1650EP H60H). Emulation of t he H8SX/1668R group is only poss ible when thi s user system interface board is c onnected to the HS1650EP H60H.
ii Content Preface ......................................................................................................... i Section 1 Configuration ..................................................................................... 1 Section 2 Connection Procedures .
1 Section 1 Configuration Figure 1 and table 1 s how the external appearance and components , respectively, of t he user system interface board for the PLQP0144KA-A package. P lease make sure you have all of these components after you have unpacked t he box.
2 CAUTION Use an NQPACK 144SD-ND socket (manufactured by Tokyo Eletech Corporation) as the PLQP0144KA- A-packaged IC socket on the user syst em. Table 1 HS1668RECH61H C omponents No.
3 Section 2 Connection Procedures 2.1 Connecting the User Sy stem Interface Board to the User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting t he two, make sure that pin 1 on both sides are correct ly aligned.
4 To connect th e board to the u ser system, follow the in structions below. 2.1.1 Installing the IC So cket After checking the locat ion of pin 1 on the IC s ocket fasten it to the user s ystem before soldering.
5 2.1.2 Soldering the IC Socket After fastening, s older the IC socket for a P LQP0144KA-A package to the us er system. CAUTION Be sure to completely solder the leads so th at the solder gently covers the leads and forms solder fillets. (Use slightly more solder than with the MCU.
6 2.1.4 Fastening the I C Socket Connector CAUTION 1. Use the screwdriver provided for t ightening screws. 2. The tightening torque must be 0.054 N•m or less. If the applied torque ca nnot be accurately measured, stop tightening when the f orce required to turn t he screw becomes significantly greater t h an that needed when f irst tightening.
7 User system interface board User system Pin 1 Screws (M2 × 10 mm) (for fastenin g the board) IC socket (NQPACK144SD-ND manufactured by Tokyo Eletech Corporation) Figure 3 Connecting the User System.
8 2.2 Exchanging the Sp acers of the Evaluation-Chip Board After connecting the user system in terface board to the us er system, be careful not to apply load to the user system. Exchange the spacers (2.6MP × 10 mm) of the evaluation-chip board with the spacers (2.
9 2.3 Connecting the User Syst em Interface Board to the Evaluation-Chip Board W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY.
10 Connector No. UCN1 UCN1 UCN2 UCN2 User system interface board Evaluation-Chip Board Connector No. Board Connector No. Evaluation-chip board Figure 5 Connecting the Us er System In terface Board to .
11 2.4 Recommended Dimensions for the User System Mounting Pad (Footprint) Figure 6 shows the recommended dimensi ons for the mounting pad (foot print) for the user s ystem with the IC s ocket for a PLQP0144KA -A package (NQPAC K144SD-ND: manufact ured by Tokyo Eletech Corporati on).
12 2.5 Dimensions of the Evaluation-Chip Board and the User System Interface Board The dimensions of the evaluati on-chip board and the user s yst em interface board are shown in figure 7. Unit: mm Tolerance: ± 0.5 mm 140.0 Evaluation-chip board User system interface board 118.
13 2.6 Dimensions after Connecting th e User System Interface Board The dimensions of the ass embly after the user system interface board has been connected to the user syst em are shown in figure 8.
14 2.7 Using the Emulator with out Connecting User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting t he two, make sure that pin 1 on both sides are correct ly aligned.
15 SW1 USER ON USER OFF Figure 9 SW1 Jumper Socket Spacer (2.6MQ x 13 mm) Figure 10 Attaching Spacers.
16 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use the screwdriver provided for t ightening screws.
17 MCU Pin 1 IC socket (NQPACK144SD-ND manufactured by Tokyo Eletech Corporation) User system Screws (M2 x 6 mm) Socket cover Figure 11 Insta lling MCU to User System.
18 Section 4 User System Interface Circuits The following user system interface circuits are required to use the emulator with the user syst em interface board.
19 MCU User system Sub-MCU P30 P31 P34 P35 P36 P37 P20 P21 47 k Ω Vcc P30 P31 P34 P35 P36 P37 P20 P21 TIOCA0 TIOCB0 TIOCA1 TIOCB1 TIOCA2 TIOCB2 TIOCA3 TIOCB3 Figure 13 User System Interface Circuit (.
20 47 k Ω Vcc P16 MCU User system SN74CB3Q3306A P16 P14 SN74CB3Q3306A P15 P15 P14 Sub-MCU SCK5 RxD5 TxD5 47 k Ω Vcc Figure 14 User System Interface Circuit (3).
21 1 k Ω 47 k Ω Vcc MD_CLK PM0-PM4 VBUS DrVcc USD- USD+ DrVss LPT16244 Monitorin g circuit MD_CLK PM0-PM4 VBUS DrVcc USD- USD DrVss Sub-MCU 47 k Ω Vcc User system EPM3256A TC MD3 Figure 15 User Sys.
22 47 k Ω Vcc UHC14 EPM7128 VHC244 _RES MCU EPM7128 _RES User system Figure 16 User System Interface Circuit (5) 47 k Ω Vcc MCU EPM3256A TC ADTRG0 SW2 1 P13 PB6 P13 3 PB6 Sub-MCU User system Figure .
23 Section 5 Verifying Operation 1. Turn on the emulator according to the pr ocedures described in the H8SX/1650 E6000H Emulator User' s Manual (HS1650EPH 60HE).
24 ⎯ To use the crysta l resonator mounted on the eval uation-chip board Install the cry stal resonator into the crystal resona tor terminals on the evaluation- chip board.
25 Section 6 Points for Caution 1. Before connecting any parts or cables, make sure that the pins at the pin 1 pos ition on both sides are correctly aligned. 2. Do not apply excessive force to the user sy stem interface board while it is connected to the user sy stem.
26 Section 7 Restrictions 1. Deep-software standby mode This emulator does not support deep-s oftware standby mode. Note that the emulator switches to the software st andby mode ev en if the register setting to select the deep-s oftware standby mode is made.
27 8. A/D converter In the emulator, the evaluation ch ip and the slave chip are used to implement fun ctions of Unit 0 and Unit 1, respectivel y, of the A/D converter.
28.
H8SX/1668R Group E6000H PLQP0144KA-A User System Interface Board HS1668RECH61H User's Manual Publication Date: Rev.2.00, April 18, 2008 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Suppor t Depar tment Global Strategic Communication Div .
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan http://www.renesas.com Refer to " http://www.renesas.com/en/network " for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.
.
H8SX/1668R Group E6000H PLQP0144KA-A User System Interface Board HS1668RECH 61H User’s Manua l.
Een belangrijk punt na aankoop van elk apparaat Renesas H8SX/1668R (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Renesas H8SX/1668R heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Renesas H8SX/1668R vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Renesas H8SX/1668R leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Renesas H8SX/1668R krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Renesas H8SX/1668R bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Renesas H8SX/1668R kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Renesas H8SX/1668R . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
