Gebruiksaanwijzing /service van het product RSKM16C6NK van de fabrikant Renesas
Ga naar pagina of 31
REG10J0017-0200 Renesas Starter Kit RSKM16C6NK User’s Manual RENESAS SINGLE-CHIP MICROCOMPUTER M16C FAMILY Rev .2.00 Renesas T echnology Europe Ltd. Revision date ： 30.
Table of Contents Chapter 1. Preface .................................................................................................................................................. 1 Chapter 2. Purpose ..............................................
Chapter 1. Preface Cautions This document may be, wholly or partially, subject to change without notice. All rights reserved. Duplication of this document, either in w hole or part is prohibited without the written permission of Rene sas Technology Europe Limited.
Chapter 2. Purpose This RSK is an evaluation tool for Renesas microcontrollers. Features include: • Renesas Microcontroller Programming. • User Code Debugging. • User Circuitry such as Switches, LEDs and potentiometer(s). • User or Example Application.
Chapter 3. Power Supply 3.1. Requirements This RSK operates from a 5V power supply. A diode provides reverse polarity protection only if a current limiting power supply is used. RSK boards are supplied with an E8a debugger module. This product is able to power the RSK boa rd with up to 300mA.
Chapter 4. Board Layout 4.1. Component Layout The following diagram shows the top layer component layout of the board. E8a Header Figure 4-1: Board Layout 4.
4.2. Board Dimensions The following diagram gives the board dimensions and connector positions. All through hole connect ors are on a common 0.1” grid for easy interfacing. MCU Application Header (Expa nsion Bu s) Application Header (LCD) RING SW 1 SW 2 SW 3 R E S POT 120.
Chapter 5. Block Diagram Figure 5-1 is representative of the CPU board components and their connectivity. Microcontroller User : 4 LEDS 1Green, 1Orange, 2Red Application Board Header s Potenti ometer .
Chapter 6. User Circuitry 6.1. Switches There are four switches located on the RSK. The f unction of each switch and its connection are shown in Table 6-1 . Switch Function Microcontroller RES When pressed the RSK microcontroller is reset. RESn SW1/BOOT* Connects to an IRQ input for user controls.
6.4. Serial port The microcontroller programming serial port 1 is connected to t he RS232 connector. A serial port can be used by moving option r esistors and fitting the D connector. This can be connect ed to serial channel 1 if the E8a is dis abled from using channel 1; or serial channel 0 while the E8a is enabled.
J11 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 Ground - 2 5V Only - 3 No Connection - 4 DLCDRS 70 5 R/W (Wired to Write only) - 6 DLCDE 69 7 No Connection - 8 No Connection - 9 No Connection - 10 No Connection - 11 DLCD4 66 12 DLCD5 65 13 DLCD6 64 14 DLCD7 63 Table 6-5: LCD Module Connections 6.
T able 6-7 below describes the function of the option links associated with Clock configuration. The default configuration is indicat ed b y BOLD text.
Ta b l e 6 - 8 below describes the f unction of the option links associated with Serial configuration. The def ault configuration is indicated by BOLD text.
Ta b l e 6 - 9 below describes the function of the opt ion links associat ed with Analog configuration. The default configuration is indicate d by BOLD text.
Option Link Settings Reference Function Fitted Alte rnati ve (Rem oved) Related To R82 Microcontroller pin function select Connects microcontroller pin 28 to IICSDA MUST be removed if R80 fitted. R80 R80 Microcontroller pin function select Connects microcontroller pin 28 to TXD2 pin Should be removed if R82 fitted .
Option Link Settings Reference Function Fitted Alte rnati ve (Rem oved) Related To R128 Microcontroller pin function select Connects microcontroller pin 47 to A21 pin MUST be removed if R130 fitted . R130 R130 Microcontroller pin function select Connects microcontroller pin 47 to CS2N pin Should be removed if R128 fitted.
6.7.Oscillator Sources A crystal oscillat or is fitted on the RSK and used to supply the main clock input to the Renesas microcontroller . details the T able 6-12 oscillators that are fitted and alternat ive footprints provided on this RSK: Component Crystal (X1) Fitted 10MHz (HC/49U package) Subclock (X2) Fitted 32.
Chapter 7. Modes The RSK supports Boot mode and Single chip mode. Details of programming the FLASH memory is described in the M16C/6NK Group Hardware Manual. 7.1. Boot mode The boot mode settings for this RSK are shown in Table 7-1: Boot Mode pin settings below: CNVSS P5.
Chapter 8. Programming Methods The board is intended for use with HEW and the supplied E8a module. Refer to the M16C/6NK Group Hardware Manual for details of programming the microcontroller without using these tools.
Chapter 9. Headers 9.1. Microcontroller Headers Table 9- 1 to Table 9- 4 show the microcontroller pin headers and their co rresponding microcontroller connections. The header pins connect directly to the microcontroller pins . * Marked pins are subject to option links.
J3 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 A19_LED3 49 2 A18_LED2 50 3 A17_LED1 51 2 A16_LED0 52 5 A15_IO7 53 6 A14_IO6 54 7 A13_IO5 55 8 A12_IO4 56 9 A11_IO3 57 10 A10_IO2 5.
9.2. Application Headers Table 9-5 and Table 9-6 below show the standard application connections . * Marked pins are subject to option links. JA1 Pin Generic Header Name RSK Signal Name Device Pin Pin.
Table 9-7 to Table 9-9 below show the optional generic header connections. * Marked pins are subject to option links. JA3 Pin Header Name RSK Signal Name Device Pin Pin Header Name RSK Signal Name Dev.
JA5 Pin Header Name RSK Signal Name Device Pin Pin Header Name RSK Signal Name Device Pin 1 ADC4 I4 AN4* 90 2 ADC5 I5 AN5* 89 3 ADC6 I6 AN6* 88 4 ADC7 I7 AN7* 97 5 CAN CAN0OUT 22 6 CAN CAN0IN 21 7 CAN.
Table 9-10 below shows the CAN connections J14 Pin Function Signal Name Device Pin 1 CAN0 Positive CAN0H 21 2 GROUND 3 CAN0 Negative CAN0L 22 J15 Pin Function Signal Name Device Pin 1 CAN1 Positive CA.
Chapter 10. Code Development 10.1. Overview Note: For all code debugging using Renesas software tools, the R SK board must be connected to a PC USB port via an E8a. An E8a is supplied with the RSK product. 10.2. Mode Support HEW connects to the Microcontroller and programs it via t he E8a.
10.4. Memory Map Figure 10-1: Memory Map 25.
Chapter 11.Component Placement Figure 11-1: Component Placement 26.
Chapter 12. Additional Information For details on how to use High-performance Embedded Workshop (HEW, refer to the HEW manual available on the CD or from the web site.
Renesas S tarter Kit for M16C/6NK User's Ma nual Publication Date Rev.02.00 30.OCT.2 007 Published by: Renesas T echnology Europe Ltd. Duke’s Meadow , Millboard Road, Bourne End Buckinghamshire SL8 5F H, United King dom ©2007 Renesas T echn ology Europe and Renes as Solutions Co rp.
Renesas S tarter Kit for M16C/6NK User's Manual Renesas T echnology Europe Ltd. Duke’s Meadow , Millboard Road, Bourne End Buckinghamshire SL8 5F H, United King dom.
Een belangrijk punt na aankoop van elk apparaat Renesas RSKM16C6NK (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Renesas RSKM16C6NK heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Renesas RSKM16C6NK vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Renesas RSKM16C6NK leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Renesas RSKM16C6NK krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Renesas RSKM16C6NK bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Renesas RSKM16C6NK kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Renesas RSKM16C6NK . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
