Gebruiksaanwijzing /service van het product PPC-154 van de fabrikant Ricoh
Ga naar pagina of 70
PPC-154 Pentium® 4 Processor-Based Panel PC with 15" Color TFT LCD Display Users Manual.
PPC-154 User’s Manual ii Copyright This document is copyrighted, © 20 04. All rights are reserved. The origi- nal manufacturer reserves the right to make improvem ents to the products described in this manual at any time wi thout notice.
iii FCC Class B This equipment has been tested and f ound to comply with the li mits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These li mits are designed to provide reasonable protection against harmful interfer- ence when the equipment is operated in a residential environment.
PPC-154 User’s Manual iv Packing List Before you begin installing your card, please make su re that the following materials have been shipped: • PPC-154 series panel PC • User's manual • Accessories for PPC-154 - Power cord (1.
v Additional Information and Assist ance Step 1. V isit the Advantech web site at www .advantech.co m where you can find the latest info rmation about the product. Step 2. Contact your distrib utor , sales representative, or Advantech's cus- tomer service center for technical support if you need additional assistance.
PPC-154 User’s Manual vi S a f e t y I n s t r u c t i o n s 1. Read these s afety instructions carefully . 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or sp ray detergents for cleaning.
vii W i c h t i g e S i c h e r h e i s h i n w e i s e 1. Bitte lesen sie Sich die se Hinweise sor gfältig durch. 2. Heben Sie diese Anleitung für den sp äteren Gebrauch auf. 3. V or jedem Reinigen ist das Gerät vom S tromnetz zu trennen. V erwenden Sie Keine Flüssig-oder Aerosolrei niger .
PPC-154 User’s Manual viii.
ix |Contents Chapter 1 General Information ........................................ 2 1.1 Introduction ............ ............................ ............ ........... ........ 2 1.2 Specifications ............ ................. ................. ..
PPC-153 User’s Manual x Chapter 4 Hardware Installation and Upgrade ............ 28 4.1 Jumpers and Connectors................ ................... ............... 28 4.2 Disassembling the Panel PC ............. ................ ............... 29 Figure 4.
xi 6.1 Introduction ......... ............................................................ 46 6.2 Driver Installation ................ ................. ................. ......... 46 6.2.1 Installation of VGA driver .. .............. ........... ....
PPC-153 User’s Manual xii.
CHAPTER 1 General Information This chapter gives background information on the PPC-154 panel PC. Sections include: • Introduction • Specifications • Dimensions.
PPC-154 User’s Manual 2 Chapter 1 General Information 1.1 Introduction Advantech PPC-154T is an Intel Pentium 4 processor–based Panel PC with 15” LCD d isplay . The powerful Pentium 4 CPU and Intel 845G V chipset with a 1 5” LCD display b rings the most dynamic applications t o life without sacrifices to any industrial reliability .
3 Chapter 1 1.2 Specifications General • Dimensions (W x H x D): 420 x 323 x 130.5 mm (16.54" x 12.72" x 5.12") • We i g h t : 7 kg (15.4 lbs) • Power supply: AC model: 180 watts Input voltage: 100~240 V AC , 4 A max. @ 50 ~ 60 Hz Output voltage: +3.
PPC-154 User’s Manual 4 • PCI bus expansion slot: Accepts one PCI bus card • W atchdog ti mer: 62-level, interval 1 ~ 62 seconds. A utomatically gen- erates system reset or IRQ1 1 when the system stops due to a program error or EMI. Jumperl ess selec tion and software enabled/disabled • Battery: 3.
5 Chapter 1 • PCI bus interface: Complies with PCI Local Bus Specification 2.1, and supports the 32-bi t Cardbus (Card-32) and the 16-bit PC card (Card-16) without external buffers • Hot insertion and removal T ouchscr een (optional) Optional Mo dules • CPU: Intel Pentium 4 or Celeron processor up to 3.
PPC-154 User’s Manual 6 Environment • T emperature : 0 ~ 45° C (32 ~ 122° F) • Relative hum idity: 10 ~ 95% @ 40° C (non-condensing) • Shock: 10 G peak acceleration (1 1 msec duration) • Power MTBF: 100,000 h rs • Certifications: EMC: CE, FCC, VCCI, BSMI approved Safety: CE, CAS, UL, CB.
CHAPTER 2 System Setup This chapter details system setup on the PPC-154 panel PC. Sections include: • A Quick T our of the Panel PC • Preparing for First-time Use • Installation Pro cedures • .
PPC-154 User’s Manual 12 Chapter 2 System Setup 2.1 A Quick T our of the Panel PC Before you start to set up th e panel PC, take a moment to become familiar with the locations and purposes of the controls, drives, connectors and ports, which are illustrated in th e figures below .
13 Chapter 2 When you look at the left side of the panel PC, you will see the flopp y disk drive, CD-ROM drive and PCMCIA exp ansion sockets, as shown in Fig. 2-2. Figure 2.2: Left side view of the panel PC When you turn the panel PC around and look at its rear cover, you will find the PC I/ISA expansio n slot located on the left sid e.
PPC-154 User’s Manual 14 2.2 Prep aring for First-time Use Before you start to set up the panel PC system, you should hav e at least the following items ready: • Power cord (in the accessory box) • Keyboard • Mouse (for system software ins tallation) 2.
15 Chapter 2 2.4 Running the BI OS Setup Program Y our panel PC is likely to have been properly set up and configured by your dealer prior to deli very .
PPC-154 User’s Manual 16 2.5 Inst alling System Sof tware Recent releases of operating system s from major vendors include setup programs which load autom atically and guide you through hard di sk preparation and operating system installation .
17 Chapter 2 2.6 Inst alling the Drivers After installing your system software, you will be able to set up the Ether- net, SVGA, audio, PCMCIA and touchscreen functions. All the drivers except the CD-ROM drive driver are st ored in a CD-ROM disc entitled "Drivers and Utilities.
PPC-154 User’s Manual 18.
CHAPTER 3 Using the Panel PC This chapter details installing the PPC-154 panel PC hardware. Sections include: • Introduction • Floppy Drive • CD-ROM Drive • PCMCIA • PS/2 Mouse and Keyboard .
PPC-154 User’s Manual 20 Chapter 3 Using the Panel PC 3.1 Introduction This chapter describes basic features and procedures for using the panel PC. T opics covered incl ude the floppy drive, CD-ROM drive, I/O ports, touchscreen, and so on.
21 Chapter 3 3.3 CD-ROM Drive T o insert a CD-ROM disc, press the eject button of the CD-ROM drive. The yellow activity lig ht will flash and the front panel will come out a short distance. Using your fingertips, hold the top and bottom of the front panel and pull it outward to the very end.
PPC-154 User’s Manual 22 3.4 Multi-card Reader Memory Flash Cards are inserted and ejected in much the s ame way as diskettes. T o insert a Flash Memory card, alig n the card with the socket and slide the card into the socket until it lock s into place.
23 Chapter 3 3.5 PS/2 Mouse and Keyboard If you wish to use a full-size de sktop keyboard and PS/2 mouse with your panel PC, follow these instructions: 1. Be sure the panel PC is turned off. 2. Attach the keyboard to the 5-pin port of the purpl e color .
PPC-154 User’s Manual 24 3.7 Parallel port The panel PC suppo rts the latest EP P and ECP parallel port protocols for improved performance and versatility with com patible printers or other devices. T o connect the panel PC to a printer or other devices: 1.
25 Chapter 3 3.9 VGA Port An external VGA-compatible device may be connected to the system through the 15-pin external port located on the rear of the system unit. The panel PC simultaneously supports an ex ternal CR T monitor in addi- tion to its own LCD display .
PPC-154 User’s Manual 26 3.12 Audio Interface The audio interface includes three jacks: microphone in, line out and line in. (See Fig. 3-5.) Their functions are: Microphone in: Use an external mi crophone to record voice and sound. Line out: Output audi o to external devices such as speakers or earphon es.
CHAPTER 4 Hardware Inst allation and Upgrade This chapter tells how to set up the panel PC hardwa re, including instr uc- tions on setting jumpers and conn ecting peripherals, switches and indicators. Be sure to read all the safety precautions before you begin the installat ion proce- dures.
PPC-154 User’s Manual 28 Chapter 4 Hardware Inst allation and Upgrade 4.1 Jumpers and Connectors The panel PC consists of a PC-based co mputer that is housed in a plastic rear panel and a metal shielding case. Y our HDD, SDRAM, power sup- ply , CPU, and so on are all readil y accessible by removing the rear panel and shielding case.
29 Chapter 4 4.2 Disassembling the Panel PC The following are standard pro cedures for disassembling the panel PC before you upgrad e your system. All procedures are i llustrated in Fig . 4-1, 4-2, 4-3 and 4-4. 1. Unscrew the three screws that secure the plastic side cover , and then remove it.
PPC-154 User’s Manual 30 3. Lift the right side of the rear cover first to remove it. Figure 4.3: Opening the rear cover Figure 4.4: The PPC without the Rear Cover 4. Unscrew the four screws that secure the CPU cover . 5. Remove the floppy dri ve, HDD, and CD-ROM cables; then remove the side panel.
31 Chapter 4 4.3 Inst alling the 2.5" Hard Disk Drive (HDD) Y ou can attach one enhanced Integr ated Device Electronics (IDE) hard disk drive to the panel PC's internal control ler which uses a PCI local-bus interface. The advanced IDE controller supports faster data transfer and allows the IDE hard drive to exce ed 528 MB.
PPC-154 User’s Manual 32 Figure 4.7: Plug the EIDE cable into the HDD Figure 4.8: Screw the right side of the metal plate to fix it Figure 4.9: Screw the left side of the met al plate to fix it.
33 Chapter 4 1. Detach and remove the plastic rear cover and side pane l. 2. There is a metal plate which holds t he HDD to the upper right-hand side of the metal shielding case. (See Fig. 4-2.) Remove the two screws on the metal plat e. 3. Pull the metal plate toward the outside of the uni t, and remove it from the two lugs of the shielding case.
PPC-154 User’s Manual 34 1. Lift up the ZIF . 2. Place the CPU carefully into the socke t. 3. Attach the heatsink and fan on to p of the CPU, and fasten them with the retention bracket.
35 Chapter 4 4. Detach.the CPU’ s fan power cable to the connector F AN1 4.5 Inst alling the D DR SDRAM Memory Module Y ou can install from 64 MB to 2 GB of DDR SDRAM memory . The panel PC system provides two 184-pi n DIMM (Dual Inline Memory Module) socket and supports 2.
PPC-154 User’s Manual 36.
CHAPTER 5 Jumper Settings and Connectors This chapter tells how to set up the panel PC hardwa re, including instr uc- tions on setting jumpers and conn ecting peripherals, switches and indicators. Be sure to read all the safety precautions before you begin the installat ion proce- dures.
PPC-154 User’s Manual 38 Chapter 5 Jumper Settings & Connectors 5.1 Jumpers and Connectors 5.1.1 Setting jumpers Y ou can configure your panel PC to match the needs of your applicatio n by setting jumpers. A jumper is the sim plest kind of electrical switch.
39 Chapter 5 5.1.2 Jumpers and switches The motherboard of th e PPC-153 has a number of jumpers that allo w you to configure your system to suit your applications. The table below list s the function of each of the board’ s jumpers. 5.1.3 Jumper Locations Figure 5.
PPC-154 User’s Manual 40 5.1.4 Connectors Onboard connectors link the panel PC to external devices such as hard disk drives or floppy drives. The table below lists the function of each of the board’ s connectors.
41 Chapter 5 5.1.5 Locating connectors Figure 5.2: Connector s on PPC-153 motherboard.
PPC-154 User’s Manual 42 5.2 CPU Inst allation Y ou can install an Intel® Pentium®4 or Celeron™ CPU without setting any frequency ratio o r voltage. *Default setting 5.3 CMOS Clear for External RTC (JP3) This jumper is used to erase CMOS data and reset system BIOS informa- tion.
43 Chapter 5 5.4 COM-port in terface (JP4, JP5) The panel PC provides two serial ports. COM1 (RS-232) and COM2 (RS- 232/422/485) in one COM port connector . 5.4.1 COM2 RS-232/422/485 setting (JP4) COM2 can be config ured to operate in RS-2 32, RS-422, or RS-485 mode.
PPC-154 User’s Manual 44 5.5 VGA interface The panel PC's AGP VGA interface can drive conventional CR T dis- plays. It is also capable of driving a wide range of flat panel displays, including electroluminescent (EL), gas plasma, passive LCD and active LCD displays .
CHAPTER 6 Driver Inst allation This chapter provides i nformation on how to install the drivers for PPC-154 Sections include: • Introduction • Installation of PPC-154 driver for W indows 98/NT/200.
PPC-154 User’s Manual 46 Chapter 6 Driver Inst allation 6.1 Introduction The PPC-154 uses the chipset 845GV from Intel., with built-in high per- formance 2D/3D Intel Extreme Graphi cs 2, flexible 10.
47 Chapter 6 6.2.1 Inst allation of VGA driver Please follow the driver path and execute it . D:PPC-154VGAwinx xxxsetup.exe. 6.2.2 Inst allation of Audio D:PPC-154audiowin xxxxsetup.exe 6.2.3 Inst allation of ICH4 USB2.0 D: PPC-154 ICH4 USB2.0 6.2.4 Inst allation of LAN D:PPC-154 Intel LAN 6.
PPC-154 User’s Manual 48 6.2.9 Further Information For further information about the AGP/VGA installation in yo ur PPC- 153, including driver updat es, trouble shooting gui des and F AQ lists, visit the following web resources: VIA website: www .via.
Appendix A Pin Assignment s.
PPC-154 User’s Manual 50 Appendix A Pin Assignment s A.1 A TX Power connector 1 (CN1) T able A.1: A T Power connector 1 (CN1) Pin Signal Pin Signal 1 3.
51 Appendix A A.2 A TX power c onnector 2 (CN2) A.3 L VDS connector 1(CN4) T able A.2: A TX power connector 2 (CN2) Pin Signal Pin Signal 1G N D 31 2 V 2G N D 41 2 V T able A.
PPC-154 User’s Manual 52 A.4 L VDS connector 2(CN6) A.5 Inverter power connector (CN5) T able A.4: T able B.4: L VDS connector 2 (CN6) Pin Signal Pin Signal 1 VDD 1 1 RXIN6+ 2 VDD 12 RXIN6- 3G N D 1 3 G N D 4 GND 14 RXIN5+ 5 CLK1+ 15 RX IN5- 6 CLK1- 16 GND 7 GND 17 RXIN4+ 8 RXIN7+ 18 RXIN4- 9 RXIN7- 19 CONTRAST 10 GND 20 HPLG_DT T able A.
53 Appendix A A.6 FDD connector (CN9) T able A.6: FDD connector (CN9) Pin Signal Pin Signal 1 Vcc(+5V) 14 S tep 2 Index 15 GND 3 Vcc(+5V) 16 Wr ite data 4 Drive select 17 GND 5 Vcc(+5V) 18 Write enabl.
PPC-154 User’s Manual 54 A.7 Internal speaker connector (CN15) A.8 IR connector (CN24) A.9 Fan power connector (F AN1 & F AN2) T able A.7: Internal speaker connector (CN15) Pin Signal 1 S pea ker out_R - 2 S pea ker out_R + 3 S pea ker out_L + 4 S pea ker out_L - T able A.
Appendix B Full Disassembly Procedure.
PPC-154 User’s Manual 56 Appendix B Full Disassembly Procedure If you want to completely disassem ble the panel PC, follow the step-by- step procedures below . Users should be aware that Adva ntech Co., Ltd. takes no responsibility whatsoever for any problems or damage cau sed by the user disassembly of the panel PC.
57 Appendix B 3. Lift the right side of the rear cover first to remove it 4. The PPC without the rear cover 5. Unscrew the board of the card reader.
PPC-154 User’s Manual 58 6. Unscrew the screw of PCI extension bus card away from PCI slot 7. Lift out the metal plate of the I/O shield from the I/O 8.
59 Appendix B 9. Lift out the cable from the CD-ROM 10. Unscrew the two screws of the bottom side to loosen the metal plate of CD-ROM / FDD module 1 1.
PPC-154 User’s Manual 60 12. Unscrew the screws to loosen th e CD -RO M a nd FD D f rom mod - ule. 13. Lift the FDD from the module. 14. Unscrew the screws from the si de of the module to loosen the.
61 Appendix B 15. Lift up the A TX 20 pins power connect or . 16. Lift up the A TX 12V 4 pins power connector . 17. Lift up the EIDE cable from mainboard.
PPC-154 User’s Manual 62 18. Loosen the screws from the bottom for remove the power modul e 19. Loosen the screws to lift up the board.
Een belangrijk punt na aankoop van elk apparaat Ricoh PPC-154 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ricoh PPC-154 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ricoh PPC-154 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ricoh PPC-154 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ricoh PPC-154 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ricoh PPC-154 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ricoh PPC-154 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ricoh PPC-154 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
