Gebruiksaanwijzing /service van het product CX-24/12 van de fabrikant Roland
Ga naar pagina of 75
CX-24/12 Thank you very much for purchasing the CX-24/12. • T o ensure correct and safe usage with a full under- standing of this product's performance, please be sure to read through this manual completely and store it in a safe location. • Unauthorized copying or transferral, in whole or in part, of this manual is prohibited.
2 Contents Windows ® , W indows NT ® and MS-DOS are registered trademarks or trademarks of Microsoft ® Corporation in the United States and/or other countries. Macintosh is a registered trademark or trademark of Apple Computer , Inc. in the USA and other countries.
3 T o Ensure Safe Use Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly . About and Notices Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly .
4 Do not injure or modify the electrical power cord, nor subject it to excessive bends, twists, pulls, binding, or pinching, nor place any object of weight on it. Doing so may damage the electrical power cord, leading to electrocution or fire. When unplugging the electrical power cord from the power outlet, grasp the plug, not the cord.
5 : Indicates information to prevent machine breakdown or malfunction and ensure correct use. : Indicates a handy tip or advice regarding use. In addition to the and symbols, the symbols shown below are also used. NOTICE Do not place hands near the platen while in operation.
6 Utilisé pour avertir l'utilisateur d'un risque de décès ou de blessure grave en cas de mauvaise utilisation de l'appareil. A vis sur les avertissements Utilisé pour avertir l'utilisateur d'un risque de blessure ou de dommage matériel en cas de mauvaise utilisation de l'appareil.
7 Ne pas utiliser avec une fiche ou un fil électrique endommagé ou avec une prise mal fixée. Une négligence à ce niveau pourrait provoquer un incendie ou une électrocution. Ne pas endommager ou modifier le fil électrique. Ne pas le plier, le tordre, l'étirer, l'attacher ou le serrer de façon excessive.
8 À propos des étiquettes collées sur l'appareil Ces étiquettes sont collées à l'extérieur de l'appareil. Les dessins suivants indiquent l'endroit et le contenu des messages.
9 1 Checking Supplied Items 1 Checking Supplied Items This product includes the items shown below . Before starting use, make sure all the items are present.
10 2 Part Names and Functions 2 Part Names and Functions In explanations that are common for both the CX-24 and the CX-12, figures depicting the CX-24 are used. Serial (RS-232C) Input Connector This is for connecting a crossover serial (RS- 232C) cable (sold separately).
11 2 Part Names and Functions [MENU/P ARAM] Key This selects whether turning the dial chooses menu items or changes setting values. Pressing this key changes the location of the menu cursor . [TEST] Key This performs a cutting test. Y ou can use it to make sure that the blade force is appropriate.
12 3 Preparing the CX-24/12 Make sure the unit is placed on a stable, sturdy surface. Installing requires the space shown below . Never install this unit in any of the following situations, as it could result in breakdown or faulty operation: • Places where the installation surface is unstable or not level.
13 3 Preparing the CX-24/12 3-2 Connection Connect the cable to either the parallel or the serial port. Be sure that the power to both the computer and the main unit is switched off when connecting the cable. Securely connect the power cord, computer I/O cable and so on so that they will not be unplugged and cause failure during operation.
14 3 Preparing the CX-24/12 3-3 Installing the Driver The included Roland Software Package CD-ROM contains a W indows-based program and driver for performing cutting with the CX-24/ 12. CAMM-1 DRIVER This software is required when sending data from a W indows-based program to the CX-24/12.
15 3 Preparing the CX-24/12 1 2 3-4 Port Setting The CX-24/12 automatically detects the port used for connection to the computer . However, if cutting data is not sent correctly , check the communication parameters for the driver and use the display menu on the CX-24/ 12 to make the same settings as for the driver .
16 3 Preparing the CX-24/12 1 2 Right-click on the icon for the driver of the model you're using then click [Properties]. For the CX-24: [Roland CAMM-1 CX-24] For the CX-12: [Roland CAMM-1 CX-12] The Properties dialog box for the model you’re using appears.
17 3 Preparing the CX-24/12 2 3 T urn the dial to display the port where the cable is connected, then press the [ENTER] key to confirm the setting. If you chose [SERIAL] in step 2, the screen for setting the bit rate appears.
18 4 Basic Operation 1 3 Insert a pin into the blade holder . Loosen the screw shown in the figure. 4 Basic Operation Be sure to support the tool mounting screw from below when installing the blade holder . Cutting quality may become poor if installed without supporting the screw in this way .
19 4 Basic Operation 5 T ighten the screw securely . T ug the blade holder upward to make sure it does not come loose. Do not use excessive force when moving the sheet loading lever . Doing so may damage it. On the CX-24, use the control panel to choose the configuration of the loaded material.
20 4 Basic Operation 1 Roller Base 2 Pass the end of the material between the pinch rollers and the grit rollers so that it extends from the front of the unit. Pull out the portion to cut from the roll. When loaded as shown in the figure, correct feed cannot be performed.
21 4 Basic Operation 3 OK Not OK 5 6 4 Stickers - CX-12 Position the material so that the left and right edges are each above one of the grit rollers. Align so that the left and right edges of the material are parallel with the guide lines.
22 4 Basic Operation 1 Turn on the CX-24/12. T urn the dial. When the display shows the type of load material, press the [ENTER] key . The cutting carriage starts to move. For the CX-24: Do not place the hands or anything else on the platen when switching on the power.
23 4 Basic Operation 2 1 2 Making Menu Settings with the Control Panel The width of the material is detected and the unit is made ready for cutting. * When flat material is loaded, the material moves to the front and rear to detect the length of the material as well.
24 4 Basic Operation 3 4-4 Checking Material Feed Make sure that the material does not come loose from the pinch rollers while cutting is in progress. On the CX-24, when you choose [PIECE] as the material type, the material is moved forward and backward in order to detect the length of the material.
25 4 Basic Operation 4 1 3 2 4-5 When Performing Long Cutting Cutting a length of 1.5 m (59 in.) or more requires material that is at least 50 mm (2 in.) wider than the necessary cutting width. Prepare material that is at least 50 mm (2 in.) wider than the necessary cutting width.
26 4 Basic Operation 1 2 3 Location of the origin point - Near the left pinch roller - Near the right pinch roller when the [ROT A TE] menu item is set to ON - At the front lower left of the material .
27 4 Basic Operation Use the position keys to move the blade holder . Move to the position where the cutting test is to be performed. The shape shown in the figure at right is cut at the present location of the blade. Peel off the material to check the result of the cutting test.
28 4 Basic Operation 1 2 3 0.1 mm 1 2 =+ T urn the dial to display the screen shown at right. Press the [MENU/P ARAM] key . The menu for setting the blade force appears. T urn the dial clockwise to increase the blade force in steps of 10 g. When the display shows the desired value, press the [ENTER] key .
29 4 Basic Operation Using the CX-24/12 to cut data created using a program requires the CAMM-1 driver . The CAMM-1 driver is in the included Roland Software Package.
30 4 Basic Operation 5 6 7 4 In the [Printers] dialog box, click [OK]. In the program window , lay out the cutting data so that it fits within the displayed cutting range. Send the cutting data from the program to the CX-24/ 12. Click the [Size] tab and make the settings for the cutting range at the screen shown at right.
31 4 Basic Operation 5 7 3 Enter the [Media Size Name], then click [OK]. * For [Media Size Name], use only alphanumeric characters. Click [Properties]. The [Properties] dialog box appears. Click the [MediaSizeSettings] document option at the screen shown at right.
32 4 Basic Operation Pausing Cutting Operations Pressing the [ENTER] key displays a screen like the one shown below and pauses cutting. - To resume cutting without change Press the [P AUSE] key again. PAUSE | <CONT.> 8 Click [Selected T ool] displays the numerals [1] through [4] and the [Machine Setting] selections.
33 4 Basic Operation 1 2 3 4 5 1 2 Pressing the [ENTER] key displays the message shown at right, and cutting stops. When Continuing with Cutting on the Same Piece of Material Set the origin point at an uncut location on the material (the location where you want to cut next).
34 4 Basic Operation 1 2 3 4 4-9 Applying the Completed Cutout When cutting ends, affix the material you created. - Before you affix the material, cleaning the location where you want to affix it to remove any dust or grease.
35 4 Basic Operation 1 2 3 4 Use the commercially available knife to sever the material along the knife guide. Use tweezers to peel off unneeded portions of the material you created. * Y ou should have weed boarders or rectangles drawn around work to facilitate weeding.
36 4 Basic Operation 1 2 3 4 Loosen the screw shown in the figure and remove the blade holder from the cutting carriage. Press the pin shown in the figure and detach the blade holder . If a blade was used, wipe the blade with a soft cloth to remove any material that may cling to it.
37 5 Performing a Self-T est 1 2 3 4 5 Performing a Self-T est The CX-24/12 is equipped with a "self-test" function to conveniently allow you to check whether or not it is capable of operating normally . If the CX-24/12 is not performing correctly , follow the steps below to perform a self-test.
38 6 Plotting on Paper Media 1 2 3 5 4 Refer to " 4-1 Installing a Blade " and install the pen by following the same steps as for installing a blade. Refer to " 4-2 Loading the Material " and load the paper by following the same steps as for loading material.
39 7 Repeating the Same Cutting 7 Repeating the Same Cutting 1 2 3 The CX-24/12 can store the data sent from the computer in a buffer (a temporary memory area), and use this data to repeat cutting. In the setup state, when cutting data is sent, the data is buffered at the same time that cutting starts.
40 7 Repeating the Same Cutting 1 2 1 2 3 1 2 Getting Ready for Recutting Repeating Cutting on Different Material Repeating Cutting Without Replacing the Material T urn the dial to display the screen shown at right. Press the [MENU/P ARAM] key . T urn the dial to display the screen shown at right.
8 Cutting Printed Material 41 Making stickers and the like involves cutting around figures that have already been printed. W ith the CX-24/12, sensors on the cutting carriage read guide marks printed on the material (crop marks) and use these to align the positioning for printing and cutting.
8 Cutting Printed Material 42 For sizes larger than A4 For A4 size (portrait) Crop Marks and Figure Layout Place the crop marks at three locations, as shown in the figure below . : There must be no soiling and no figures other than crop marks within this area.
8 Cutting Printed Material 43 How to lay out figures for cutting Creating Data and Printing the Material 1 From [File] menu, click [Document Setup]. The [Document Setup] dialog box appears. 2 For [Units], choose [Millimeters]. Cutting around a figure Cutting inside a figure 4 Click [Print Setup].
8 Cutting Printed Material 44 9 Lay out the figure inside the crop marks. 10 From [File] menu, choose [Print] to perform output to the printer you're using. 7 Click [OK]. The preview window appears. 8 This example uses the layout and positioning of crop mark for A4-size material.
8 Cutting Printed Material 45 SELECT | ROLL Loading Output Material on the CX-24/12 1 Position the pinch rollers outside the crop marks. 2 Orient the material so that its long edges are parallel to the material-feed direction of the CX-24/12. Position the crop marks above the blade protector .
8 Cutting Printed Material 46 7 T urn the dial to choose [AUTO], then press the [ENTER] key . T urning the dial while in the state shown at right sequentially displays the menus for detecting crop marks. Refer to the following for making the menu settings.
8 Cutting Printed Material 47 9 For the CX-24 Depending on the type of material loaded, choose [PIECE] or [ROLL], then press the [ENTER] key . For the CX-12 Press the [ENTER] key . The cutting carriage moves to the left and detection of the crop marks starts.
8 Cutting Printed Material 48 5 Move the origin point for the page to match the crop mark you laid out at the lower left in " Creating Data and Printing the Material ." In Illustrator's toolbox, choose the page tool ( ) and move the center of the page tool to the location shown in the figure.
8 Cutting Printed Material 49 8 From the [File] menu, choose [Print]. The [Print] dialog box appears. 9 Clear the [Bitmap Printing] check box. 10 Click [OK]. The CX-24/12 cuts the data that has the line you specified for cutting. If the program you're using has the following features, they may be handy in laying out crop marks accurately .
8 Cutting Printed Material 50 Are the layout locations for the marks correct? Refer to " 8-2 Shape and Layout of Crop Marks " to lay out the crop marks correctly .
51 9 About the Blades and Materials 9-1 Blade and Material Combinations The table below provides information on combinations of materials and blades, cutting conditions, and useful life. The figures for blade life are only estimates. The conditions described below may not apply all cases.
52 9 About the Blades and Materials * Make sure the pinch rollers are positioned above the grit rollers. * Make sure the pinch rollers are positioned above the grit rollers. The location of the grit rollers (where the material is held in place by the pinch rollers) differs according to the model.
53 9 About the Blades and Materials The cutting area along the horizontal plane (the direction in which the tool carriage moves) is determined by the position of the pinch rollers. The workable area spans the length between the two rollers, minus a mar gin of about 1 mm (about 0.
54 9 About the Blades and Materials Rubber Sandblast Stencils Use rubber sandblast stencils that meet the conditions shown in the figure at right. A) Materials with a material thickness of 1 mm (0.
55 10 Display Menu Descriptions 10-1 How to Read This Chapter The explanations in this chapter use the following format. ROLL: This performs cutting using roll material. EDGE: When using roll material, cutting is performed from the front-left edge of the material.
56 10 Display Menu Descriptions CROPMARK| <OFF> Stored in Memory Factory Default Selection Choices Description CROPMARK BASE X | <5mm> Stored in Memory Factory Default Setting Range Descri.
57 10 Display Menu Descriptions WIDTH | <170mm> Stored in Memory Factory Default Setting Range Description WIDTH Steps LENGTH | <210mm> Stored in Memory Factory Default Setting Range Descr.
58 10 Display Menu Descriptions Stored in Memory Factory Default Setting Range Steps Description FORCE | < 50g> Stored in Memory Factory Default Setting Range Steps Description Ye s 50 g 30 to 200 g 10 g This sets the blade force used when cutting material.
59 10 Display Menu Descriptions Stored in Memory Selection Choices Description No ST AR T , CLEAR ST ART This performs cutting using the data in the replot buf fer when the [ENTER] key is pressed. CLEAR This deletes the data in the replot buf fer when the [ENTER] key is pressed.
60 10 Display Menu Descriptions Stored in Memory Factory Default Selection Choices Description Ye s LIGHT LIGHT , HEA VY Sets the weight of the material. If material feed is not performed smoothly , set this switch to [HEA VY]. When set to [HEA VY], the upper limit for the cutting speed is set at 10 cm/ sec.
61 10 Display Menu Descriptions Stored in Memory Factory Default Selection Choices Description Ye s 9600 9600, 4800 This sets the communication speed for a serial connection. It is effective only when connected to the computer using a serial cable. #BAUD.
62 10 Display Menu Descriptions Stored in Memory Factory Default Selection Choices Description Ye s ENGLISH ENGLIS, , Deut., FRANÇ, , IT AL.,POR TUG, This selects the language for messages on the display . T o display this menu, switch on the power while holding down the [MENU/P ARAM] key .
63 1 1 Display Menu Flowchart 1 1 Display Menu Flowchart T o display the setting values for the various menu items, press the [MENU/P ARAM] key . For detailed information on how to make menu settings, see "4-3 T urning on the Power - Making Menu Settings with the Control Panel .
64 1 1 Display Menu Flowchart SETUP -> ENTER CROPMARK|<OFF> BASE X | <5mm> BASE Y | <5mm> WIDTH |<170mm> LENGTH|<210mm> A UTO, OFF 0 to 50 mm 0 to 50 mm 50 to 610 mm 5.
65 12 What to do if... 1 2 12 What to Do If... 12-1 If the CX-24/12 Doesn't Run... Is the CX-24/12 power on? Turn on the power . Is the CX-24/12 in the setup state? When the display shows the following message, cutting cannot be performed even when data is sent.
66 12 What to do if... Has the correct driver selection been made for the application program? (Using with Windows.) Select the appropriate CX-24/12 driver . For the CX-24: [Roland CAMM-1 CX-24] For the CX-12: [Roland CAMM-1 CX-12]. Are the settings for the driver program correct? (Using with Windows.
67 12 What to do if... 12-3 Uncut Areas Remain, or Areas Are Not Cleanly Cut Are the blade and blade holder securely mounted? Install these so that there is no looseness . The blade may be broken. Replace with a new blade. Is there any buildup of dust or material adhesive on the tip of the blade? Check if there are any dirty deposits on the blade.
68 12 What to do if... 12-5 Error Messages The location of one or more of the pinch rollers is not correct. Press the [ENTER] key to clear the error . Position the pinch rollers appropriately over the grit rollers and reload the material. Refer to " 4-2 Loading the Material .
69 12 What to do if... Meaning Appears if a framing error , parity error , or overrun error occurs at the time of data reception. The protocol settings for the CX-24/12 must be made correctly in order to match the settings your computer is set to use.
70 13 Instruction Support Chart 13 Instruction Support Chart A "CAMM-GL III Programmer's Manual" is available for separate purchase for those wishing to create their own programs for this machine. For further information, please contact your authorized Roland dealer or service center .
71 14 Specifications Driving method Maximum cutting area Acceptable media widths Acceptable paper widths Acceptable paper types T ools Max. cutting speed Blade force Mechanical resolution Software res.
72 14 Specifications 1 19 18 36 3.3K +5 V = * 1 14 13 25 Signal T erminal Signal Pin Connection number number number NC 36 18 HIGH* HIGH* 35 17 GND NC 34 16 GND GND 33 15 NC HIGH* 32 14 NC NC 31 13 HI.
73 Index Index A Acceptable material widths ................................................... 52 Affix the material .................................................................. 34 Amount of blade extension .....................................
74 Index Positioning the grit rollers ..................................................... 20 R Recutting ............................................................................... 40 Removing the material .......................................
R5-03012 4.
Een belangrijk punt na aankoop van elk apparaat Roland CX-24/12 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Roland CX-24/12 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Roland CX-24/12 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Roland CX-24/12 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Roland CX-24/12 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Roland CX-24/12 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Roland CX-24/12 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Roland CX-24/12 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
