Gebruiksaanwijzing /service van het product CW-95DHD van de fabrikant Runco
Ga naar pagina of 106
CineWall™ CW-95DHD Full-HD, 2.35:1 In-Wall Display and Digital High Definition (DHD™) Controller/Scaler/Processor I NSTALLER /I NTEGRATOR M ANUAL.
To register you r Runco prod uct and obtain information about warranty and se rvice off erings, please visit http://www .runco.com/in fo.html. © Copyright 200 9 Runco Internatio nal, LLC (“Runco”). This d ocument contain s proprietary info rmation prote cted by copyrigh t, trademark a nd other intellect ual property laws.
CineWall™ Installer/Integrator Manual iii PRE L IMINAR Y Thank you for you r purchase of this quality Run co video product! It ha s been designed to pr ovide you with the qualit y of video that is exp ected in a ho me theater . For the best p erformance , please read this manual carefully as it is you r guide thro ugh the menus and operat ion.
iv CineWal l™ Installer/Integrator Manual PRE L IMINAR Y Manufacture r’s Name: Runc o International, LLC Manufacture r’s Address: 1195 NW Compton Drive, Beaverton, OR 97006-1992 hereby declare s.
CineWall™ Instal ler/ Integrator Manual v PRE L IMINAR Y And: • EN 61000-3-2 “Electromagn etic compatibility (EMC) Part 3, Section 2: Limits for harmonic current emissions (equipment input curre.
vi C ineWall™ Installe r/Integrator Manual PRE L IMINAR Y The Product contains sm all amounts of tin, lead and/or mer cury. Disposal of these mate rials may be regulated due to environmenta l consideratio ns. Lamp(s) ins ide this pro duct contain me rcury.
CineWall™ Instal ler/In tegrator Manual vii 1 Table of Content s PRE L IMINAR Y Important S afety In s truction s ....................... ................... ................ ................ .............. iii Compliance Information .............. .
Table of Contents viii CineWall™ Insta ller/Integrator Ma nual PRE L IMINAR Y 4. In s tallation ..... ................ ................ ................... ................ ................ ................. ...... 25 Overview ...... ...............
Table of Contents CineWall™ Instal ler/In tegrator Manual ix PRE L IMINAR Y Lamp Repla cement ................... ................. ................ ................ ................ ................ 75 Removing the Old Lamp ... ................ ...
Table of Contents x CineWall™ Installer/Integrator Manual PRE L IMINAR Y Note s :.
CineWall™ Instal ler/In tegrator Manual xi 1 Li s t of Figure s PRE L IMINAR Y 2-1. Chassis Ins tallation Bracket s ............ ................ ................... ................ ................. ........ 7 2-2. DHD Contro ller Front Pane l ...
List of Figures xii CineWal l™ Installer/Integrator Manual PRE L IMINAR Y Note s :.
CineWall™ Instal ler/ Integrator Manual 1 PRE L IMINAR Y 1.1 About This Manual This Owner’s Ma nual describes how to install, set up and operate a Runco CineWall™ Full HD, In-Wall Display and DHD Controller. Throughout th is manual, the Runco CineWall™ Full HD, In-W all Display and DHD Controller is referred t o as the “Cin eWall.
Introduc tion 2 CineWall™ Installer/Integrator Manual PRE L IMINAR Y G raphic Convention s : These symbols appear in numerous pl aces througho ut the manual, to emp hasize points th at you must keep in mind to avoid problems with your equipment o r injury: 1.
Introd uction CineWall™ Instal ler/ Integrator Manual 3 PRE L IMINAR Y 1.3 Description, Features and Benefits Runco, the leading bran d in luxury video solutions, pr oudly announces its new CineWall.
Introduc tion 4 CineWall™ Installer/Integrator Manual PRE L IMINAR Y Key Features and Benefits The CineWall offers these key fea tures and benefits: • Native Resolution: 1920 x 817 (2 .35:1 Native Aspect Ratio) • Screen Size: 95 -inch diagonal m easure (approxima tely 88.
CineWall™ Instal ler/ Integrator Manual 5 PRE L IMINAR Y This section briefly d escribes the v arious CineWall system co mponents. 2.1 Chassis Assembly The Chassis Assem bly is a sheet metal assembly tha t contains all of the active components o f the CineWall, as sh own below.
System Description 6 CineWall™ Installer/Integrator Manual PRE L IMINAR Y Input Connectors and LEDs The CineWall interf ace board is equipped with th e following input c onnectors and LED indicators: 1. R S -232 (RJ-45) Connect the Di s play Control output on the DHD Controller to this input (see Figure 2-3 ).
System Description CineWall™ Instal ler/ Integrator Manual 7 PRE L IMINAR Y 2.3 Chassis Installation Brackets To reduce the o verall depth of the c hassis assembly for shipping, the installation brack ets that secure t he chassis and scr een to the wall ar e packaged sep arately.
System Description 8 CineWall™ Installer/Integrator Manual PRE L IMINAR Y 2.4 Other Syst em Components Power S upply: The Power Supply co nverts incoming 10 0-240 VAC power to the in ternal working voltages required by the lamp ballast, video proce ssor and other system components.
System Description CineWall™ Instal ler/ Integrator Manual 9 PRE L IMINAR Y 1. RUNCO ICON Lights blue to indicate tha t the controlle r is on or powering up. 2. IR S EN S OR Receives IR commands fro m the remote contro l. 3. V A CUUM FLUORE S CEN T DI S PLA Y Can be used instead of the On-Screen Displ ay (OSD).
System Description 10 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y 2.6 DHD Controller Rear Panel Figure 2-3 show s the rear connec tor panel on the DHD Con troller. Figure 2-3. DHD Controller Rear Panel Outputs 1. HDMI Out Connect this t o the HDMI connector on the Cin eWall (see Input Connectors a nd LEDs on page 6).
System Description CineWall™ Instal ler/ Integrator Manual 11 PRE L IMINAR Y 9. S -Video 1 / S -V ideo 2 Two, standard S-Video inputs for connecting a DVD play er, satellite receiver or Super VHS (S-VHS) VCR. 10. IR Wired input from a Niles- or Xantech-compatib le, infrared (IR) repe ater system.
System Description 12 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y 1. IR OUTPUT INDICA TOR Lights when a button is pressed to indicate t hat an IR signal is be ing transmitted. 2. ON / OFF Press to tu rn the display on or off. 3. ENTER Press to select a h ighlighted men u item or confirm a changed settin g.
System Description CineWall™ Instal ler/ Integrator Manual 13 PRE L IMINAR Y 10. A s pect Ratio S election Butto n s Use the red b uttons to selec t an aspect rat io directly or to enter numeric cha racters, as follows: 16:9 (3) For viewing 16 :9 DVDs or HDTV p rograms in their native aspect ratio.
System Description 14 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Note s :.
CineWall™ Instal ler/ Integrator Manual 15 PRE L IMINAR Y 3.1 Site Requirements Prior to install ing the CineWall, c onfirm that the instal lation site meets th e requirements described in this section. Infrastructure The CineWall is d esigned for insta llation into a d edicated, frame d, structurally capab le wall with at least 32.
Installation Preparation 16 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Power Requirements The CineWall r equires clean, no ise-free AC power. The p ower cord provid ed with the CineWall is 6 feet ( 1.83 meters) long . In order to use it, the power o utlet must be no more than 48 inch es (1.
Installation Preparat ion CineWall™ Instal ler/ Integrator Manual 17 PRE L IMINAR Y Also confirm tha t doorways and elevators (if use d) provide suf ficient clear ances: Audio/Video Synchronization .
Installation Preparation 18 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Additional Consideration s Here are some other considerations and tips that can help imp rove your installat ion, avoid damage, pr event person al injury and prolong opera ting life: • Keep the ambi ent temperature constant and below 3 5°C (95°F).
Installation Preparat ion CineWall™ Instal ler/ Integrator Manual 19 PRE L IMINAR Y 3.2 Unpacking and Inspecting When you rece ive your CineWall shipm ent, check the shipping containe rs for damage. If there are signs of da mage or rou gh handling, it is recommend ed that you have an agen t of the carrier pre sent when the equipment is unpacked.
Installation Preparation 20 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y 4. With the he lp of your assistant, grasp the chass is by the hand les on either side a nd lift it straig ht up and out of t he shippin g container.
Installation Preparat ion CineWall™ Instal ler/ Integrator Manual 21 PRE L IMINAR Y 3.3 Site Preparation Because every home theater in stallation is un ique, it is impossible to provide detailed, step-by-step ins tructions that are applicable to every situation.
Installation Preparation 22 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Create wall opening: 1. Locate the screen c enter based on the desired s creen height. 2. From this point, meas ure/mark 44.3 75 inches to the left and t o the right a nd 19.
Installation Preparat ion CineWall™ Instal ler/ Integrator Manual 23 PRE L IMINAR Y 6. Frame the wall opening in a manner simila r to this exam ple. 38.
Installation Preparation 24 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Note s :.
CineWall™ Instal ler/ Integrator Manual 25 PRE L IMINAR Y 4.1 Overview Table 4-1 gives a quick overview of the CineWall installa tion process. Th e sections following this one pr ovid e detailed ins tructions. 4. In s tallation Table 4-1. In s tallation Overview S tep Procedure For Detail s , Refer to page.
Installation 26 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y 4.2 Mounting the CineWall Chassis This section provides detailed instruct ions for installing the CineWall chas sis. Install Top Flange a nd Bottom Brackets on Chassis As sembly Install the Top Flange as shown in F igure 4-1.
Installation CineWall™ Instal ler/ Integrator Manual 27 PRE L IMINAR Y Install Chassis Assembly into Wall With the help of your a ss i s tant( s ), lift the Chassis Asse mbly by the hand les. While tilting the Chassis Asse mbly downward, ca refully move the Chassis Assemb ly into the wall openin g.
Installation 28 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y The CineWall includes a special spacing to ol to make it easie r to level the Top Flan ge and ensure that it is the co rrect distance f rom the Bottom B rackets. 1. Place the Spacing Tool on either the Le ft Center or Right Center Bott om Bracket, a s shown.
Installation CineWall™ Instal ler/ Integrator Manual 29 PRE L IMINAR Y 5. Secure the Left and Right Side Light Blocks to the chassis a nd the opening frame. 6. Secure the Bott om Center Light Block/Strut Ca tch to the opening frame, betwe en the two Center Bo ttom Brackets .
Installation 30 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y 4.3 Installing the Screen Figure 4-2 shows the CineWall scr een assembly. The screen at taches to the hinge on the top flange o f the Chassis Assembly via six hooks along the top of the frame.
Installation CineWall™ Instal ler/ Integrator Manual 31 PRE L IMINAR Y To install the screen: 1. Remove the Spacing Too l (used to install t he chassis; see pag e 28 ). 2. With the h elp of your assistant(s) , lift the screen and position it in f ront of the Cha ssis Assembly.
Installation 32 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y 3. Use the h ooks to hang t he frame on th e hinge at the top of the chassis. 4.
Installation CineWall™ Instal ler/ Integrator Manual 33 PRE L IMINAR Y 5. Install the safety catches at t he top rear co rners of the screen. These prev ent the screen fr om separating fro m the hinge when the s creen is opened or closed. a Remove the nut at one end of the hing e wing on the back of the screen.
Installation 34 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y 4.5 Aligning the Image The CineWall opti cal engine was pe rfectly adjusted wh en it left the facto ry.
Installation CineWall™ Instal ler/ Integrator Manual 35 PRE L IMINAR Y 4.6 Connections to the CineWall Proceed as follows t o connect the CineWa ll to your video sourc es, external contr oller(s) – if present – an d AC power. When connect ing your equipmen t: • Turn off all equipment be fore making any connection s.
Installation 36 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Connecting the CineWall to the DHD Controller Connect the DHD Controller to t he CineWall as shown in Figure 4-3 and described in the sections th at follow.
Installation CineWall™ Instal ler/ Integrator Manual 37 PRE L IMINAR Y Digital Video Connection: Connect the HDMI output from the DHD Controller to the HDMI input on the CineWall, using an HDMI-to-HDMI cable. R S -232 Connection: Connect the Di s play Control output fr om the DHD Controller to the R S -232 input on the CineWall.
Installation 38 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Connecting Source Components to the DHD Controller Connect your vid eo sources to t he DHD Controller as sh own and de scribed in the sections th at follow. HDMI S ource Connection s : See Figure 4-5.
Installation CineWall™ Instal ler/ Integrator Manual 39 PRE L IMINAR Y Compone nt Video S ource Connection s : Connect yo ur componen t video sources to the HD1, HD2 a nd/or Componen t/SCART inputs as sho wn in Figure 4-6 .
Installation 40 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y R G BHV S ource Connection s : Connect pe rsonal computers an d/or other RG B sources to the HD1, H D2 and/or Com ponent/SCART inputs a s shown in Figure 4 -7 .
Installation CineWall™ Instal ler/ Integrator Manual 41 PRE L IMINAR Y S CART R G B S S ource Connection s : Connect the green , blue and re d outputs fr om your SCART source to the Componen t/SCART input on the DHD Controller. Conne ct the sync output from your SCART source to the Video in put on the DHD Controller .
Installation 42 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Compo s ite and S -Video S ource C onnect ion s : See Figure 4-9. Figure 4-9. S -Video an d Compo s ite Video S ource Connect io.
Installation CineWall™ Instal ler/ Integrator Manual 43 PRE L IMINAR Y RS-232 Controller Connection Use a straight-th rough, 9-pin RS-232 cable to connect a PC or contro l/automation system (if present) to th e RS-232 port on th e DHD C ontroller; see Figure 4-10 .
Installation 44 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Connecting 12-volt Trigger Outputs to External Equipment If your installation inc ludes equipme nt that responds to 12-volt trigg ers, connect it t o the 12-volt trigger outpu ts as shown in Figure 4 -11 .
Installation CineWall™ Instal ler/ Integrator Manual 45 PRE L IMINAR Y Connecting an External IR Receiver to the DHD Controller If infrare d signals from the r emote control ca nnot reach the DHD Co.
Installation 46 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y 4.7 Installing Batteries in the DHD Controller Remote Control To install batte ries in the DHD Co ntroller remote control: 1. Press down the tab on the cover and pull the cover in th e direction of the arrow.
Installation CineWall™ Instal ler/ Integrator Manual 47 PRE L IMINAR Y • Make sure tha t there is nothing obstructing the infrared bea m between the remot e control and the IR receive r on the plasma display. • If the effective r ange of the re mote control d ecreases, or it st ops working, re place the batteries w ith new ones.
Installation 48 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Note s :.
CineWall™ Instal ler/ Integrator Manual 49 PRE L IMINAR Y 5.1 On-Screen Display (OSD) Menus To display t he Main Menu , press the MENU b utton on the r emote control (Figure 2-4) or DHD Controller front panel ( Figure 2-2 ). To select a menu it em, use the and buttons on the remo te control or DHD Cont roller front panel to h ighlight it.
Operation 50 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Figure 4-1. CineW all O S D Menu S tructure (contin ued) Main Menu The Main Menu is the starting point for accessing all CineWall functions. (You must ente r a passco de to access th e Calibration and Service menus.
Operation CineWall™ Instal ler/ Integrator Manual 51 PRE L IMINAR Y Input Source From the M ain Menu, selec t Input Source to choose a vid eo signal source. The active source is indic ated by an arrow ( ➡ ) to its left; in this example, Comp osite is the active source .
Operation 52 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Table 5-1. A s pect Ratio S etting s A s pect Ratio Remote Control Key A s pect Ratio of S ource S ignal De s cription 16:9 16:9 16:9 Select 1 6:9 to view 16:9 DVDs a nd HDTV programs in their native aspect ratio.
Operation CineWall™ Instal ler/ Integrator Manual 53 PRE L IMINAR Y Letterbox LBOX 16:9 Letterbox mode scales (zooms in on) a 4:3 image linearly (by the same amoun t on all sides) to fill a 16:9 display. Letterbox is best suited for viewing LaserDisc movies or non-anamorphic DVDs on a 16:9 screen.
Operation 54 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Cinema CINEMA 2.35:1 Select Cinema to vi ew 2.35:1 source material in it s native aspect rati o. Cinema masks the upper and lower por - tions of the screen to create a viewable area with a 2.
Operation CineWall™ Instal ler/ Integrator Manual 55 PRE L IMINAR Y Native (none) 16:9 Select One to One to display the source signal in its native resolution, with no re-sizing or overscan. This means, for example, that 720p HDTV programs will display with unused pixels on all sides: 320 on the left and right sides and 48 above and below.
Operation 56 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Picture Use the contr ols in the Pictu re Menu to ca librate your Cine Wall for optimum p icture quality. The CineWall has been design ed to incorpora te setup and calibration stan dards established b y the Imaging Scie nce Foundation (ISF).
Operation CineWall™ Instal ler/ Integrator Manual 57 PRE L IMINAR Y PLUGE patterns va ry but gener ally consist of some combination of black, white an d gray areas against a blac k background. T he example above includ es two vertical bar s and four shaded boxes.
Operation 58 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Color S aturation: On your e xternal test patt ern source, select a color ba r pattern like the one shown in Figure 5-4 . Figure 5-4. Typical Color Bar Pattern for Adju s ting Color S aturation and Tint 1.
Operation CineWall™ Instal ler/ Integrator Manual 59 PRE L IMINAR Y 11.Adjust the color sa turation level until the outer most (gray and blue) color bars appear to be a single shade of bl ue: Tint: Tint or “hue” is essentially the rat io of red to green in the color portion of the image .
Operation 60 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y S harpne ss : “Sharpness” is th e amount of high-frequency detail in th e image. T o adjust sharpness, select Shar pness from the Picture me nu and press ENTER . On your external test pattern source, sele ct a pattern like the one show n in Figure 5-5 .
Operation CineWall™ Instal ler/ Integrator Manual 61 PRE L IMINAR Y Input Position Use the controls in the Input Position Menu to fine-tune the aspect ratio a nd image position for th e current sour ce. Left/Right: Select Left/Right from the Input Position menu to shift the pr ojected image horizontally.
Operation 62 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Figure 5-6. Over s can Mode s Pha s e (R G B or Component s ource s ): This control adjusts th e phase of th e pixel sampling clo ck relative to the incoming signal.
Operation CineWall™ Instal ler/ Integrator Manual 63 PRE L IMINAR Y Memory Presets For each inp ut, the CineWall lets yo u save image qu ality settings as presets that you can recall at a la ter time. You can create up to four presets pe r input and di splay mode (resolution and frame rate).
Operation 64 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y To reset the Custom 1 or Custom 2 mem ory preset to its factory-def ault state, select it, press or to highlig ht Reset and pr ess ENTER .
Operation CineWall™ Instal ler/ Integrator Manual 65 PRE L IMINAR Y • G amma: Select Gamma from the Display Color m enu to choose a de-gamma curve. Used correctly , the Gamma cont rol can impro ve contrast w hile maintaining go od details for b lacks and whites.
Operation 66 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y • S imple : Select Simple mode from the Color Temp menu (with the C ineWall, this is the only choice) to choose one of thre e color temperatu re presets: 3200K , 5500K or 6500K. The de fault setting, 6500K, is appr opriate for most situ ations.
Operation CineWall™ Instal ler/ Integrator Manual 67 PRE L IMINAR Y S ave I S F Night/ S ave I S F Day: Whenev er you make a c hange to the ISF settings, you should always save it. Select Save ISF Night or Save ISF Day from the Calibration menu to do this.
Operation 68 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y • S pla s h Enable: When you have finishe d customizing the s plash screen, sele ct Splash Enable from the Splash Configure men u.
Operation CineWall™ Instal ler/ Integrator Manual 69 PRE L IMINAR Y Remote Control: Select Remote Cont rol from the Service m enu to change the following settings related to remote cont rol operation. • Remote Code: Select Remo te Code from the Remote Cont rol menu to set the infrared (IR) code set to which the CineWall will re spond.
Operation 70 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Color S pace: Select Color Space from th e Service menu to choose the co lor space of the source signal for HDMI, RGB, an d component co nnections.
Operation CineWall™ Instal ler/ Integrator Manual 71 PRE L IMINAR Y • CUE (Chroma Up s ampling Error) Correction: Some DVD players use MPEG decoders that do not correc tly “upsample” th e 4:2:0 forma t chroma info rmation on th e DVD to the 4:2: 2 or 4:4:4 form at required by the video enco der of the disp lay device.
Operation 72 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Note s :.
CineWall™ Instal ler/ Integrator Manual 73 PRE L IMINAR Y 6.1 Cleaning Cleaning the Scr een, Mirrors and Lens Dirt is everywhere, and unless the CineWall is in a super-cle an room, from time to time yo u will need to clean the scre ens, mirrors and/or lens.
Maintenance and Troublesho oting 74 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Removing dry du s t: Often the clea ning problem is just du st, not fingerpr ints or other oily dirt. If it’s just d ust, wiping with a dry cheesecl oth or a dry Shop Towel will usually do the job.
Maintenance and Troubleshooting CineWall™ Instal ler/ Integrator Manual 75 PRE L IMINAR Y 6.2 Lamp Replacement Change the lamp after 6,000 hour s of u s e, or s ooner if you notice a s ignificant decre a s e in brightne ss . Removing the Old Lamp 1.
Maintenance and Troublesho oting 76 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Installing the New Lamp 1. Re-c onnect the lamp cable you discon nected in Step 5 ab ove. Make sure it is fully seated. 2. Mount the lam p in its place. Note the two pins op posite the lamp screw.
Maintenance and Troubleshooting CineWall™ Instal ler/ Integrator Manual 77 PRE L IMINAR Y Removing the Air Filter 1. Open th e screen. 2. Turn o ff the AC power sw itch and remove the power cord. 3. Lift the a ir filter up and toward you. Then, replace it with a n ew one (Runco p art number 379-0 012-00).
Maintenance and Troublesho oting 78 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Isolating Faulty Part s If you suspect that a pa rt may be faulty, re place it wit h a known-good one if available . This is a very effect ive way to find a p roblem.
Maintenance and Troubleshooting CineWall™ Instal ler/ Integrator Manual 79 PRE L IMINAR Y • A fan may have fa iled. Most fans are sen sed. That mean s the electronics mo dule knows whet her they are running or n ot.
Maintenance and Troublesho oting 80 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Note s :.
CineWall™ Instal ler/ Integrator Manual 81 PRE L IMINAR Y 7.1 RS-232 Connection and Port Configuration To interface the CineWall with an automation/control system or a PC running terminal emulation softw are, connect it to the Di s play Control output of the DHD Controller as shown in Figure 4-3 and Fig ure 4-4 .
Serial Communications 82 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Table 7-1 lists the RS-232 comman d set. The “Paramet er (min/ma x)” column shows th e valid parameter ranges, or “NA” for comman ds that take no paramet ers.
Serial Communications CineWall™ Instal ler/ Integrator Manual 83 PRE L IMINAR Y A s pect Ratio Command s 16:9 NA YES Selects the 16:9 aspect ratio 4:3 NA YES Selects the 4:3 aspect ratio ASPECT? NA .
Serial Communications 84 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Image Pre s et Command s CUSTOM1 NA YES Loads “Custom 1” image preset CUSTOM2 NA YES Loads “Custom 2” image pre.
Serial Communications CineWall™ Instal ler/ Integrator Manual 85 PRE L IMINAR Y Mi s cellaneou s Command s DISPLAY? NA NA Returns display device input source value, as follows: 1 = Auto 36 = CW-95DH.
Serial Communications 86 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y Note s :.
CineWall™ Instal ler/ Integrator Manual 87 PRE L IMINAR Y 8.1 CineWall Specifications Table 8-1 lists the CineWall specif ications. 8. S pecification s Table 8-1.
Specifications 88 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y 8.2 DHD Controller Specifications Table 8-2 lists the DHD Controller specifications.
Specifications CineWall™ Instal ler/ Integrator Manual 89 PRE L IMINAR Y 8.3 Dimensions Figure 8-1 shows the CineWall CW-95DHD dimensions ( all dimensions are in inches). Figure 8-1. CineWa ll CW-95HD Dimen s ion s 94.72 42.07 92.14 8.00 104.00 144.
Specifications 90 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y 8.4 Supported Timings Table 8-3 lists the s ignal types suppor ted by each input on the DHD C ontroller.
Specifications CineWall™ Instal ler/ Integrator Manual 91 PRE L IMINAR Y 1280x1024 1280x1024 60.00 63.981 108.000 √√√ ––– 75.00 79.976 135.000 √√√ ––– 85.00 91.146 157.500 √√√ ––– 1360x768 1360x768 60.00 47.712 85.
Specifications 92 CineWall™ Installe r/Integrator Manual PRE L IMINAR Y PAL-M – 59.94/60.00 15.73 4/15.750 3.580 –––– √ √ PAL-N – 50.
.
Runco International • (800) 23RUNCO • Fax (503) 748-8161 • www.runco.com SERIAL NUMBER 020-0981-00 Rev. A March 2009.
Een belangrijk punt na aankoop van elk apparaat Runco CW-95DHD (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Runco CW-95DHD heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Runco CW-95DHD vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Runco CW-95DHD leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Runco CW-95DHD krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Runco CW-95DHD bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Runco CW-95DHD kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Runco CW-95DHD . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
