Gebruiksaanwijzing /service van het product DBJ50 van de fabrikant Ryobi
Ga naar pagina of 22
SA VE THIS MANUAL FOR FUTURE REFERENCE OWNER'S OPERA TING MANUAL DET AIL BISCUIT JOINER / DBJ50 DOUBLE INSULA TED THANK YOU FOR BUYING A RYOBI DETAIL BISCUIT JOINER. Your new detail biscuit joiner has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety.
Page 2 RULES FOR SAFE OPERA TION The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger.
Page 3 1. KNOW YOUR POWER TOOL. Read owner's manual carefully. Learn its applications and limitations as well as the specific potential hazards related to this tool. 2. GUARD AGAINST ELECTRICAL SHOCK BY PREVENTING BODY CONTACT WITH GROUNDED SURFACES.
Page 4 RULES FOR SAFE OPERA TION (Continued) 25. INSPECT TOOL CORDS PERIODICALLY and if damaged, have repaired at your nearest authorized service center. Stay constantly aware of cord location and keep it well away from the rotating blade. 26. INSPECT EXTENSION CORDS PERIODI- CALLY and replace if damaged.
Page 5 TABLE OF CONTENTS ■ Rules For Safe Operation ........................................................... 2-4 ■ T able of Contents / Introduction ..................................................... 5 ■ T ypical Applications .............
Page 6 EDGE-TO-EDGE JOINTS DETAIL BISCUIT JOINER / DBJ50 TYPICAL APPLICA TIONS BUTT JOINTS T- JOINT MITER JOINTS 0 1 2 3 1 2 5 1 6 3 4 4 5 ° 9 0 °.
Page 7 FEA TURES W ARNING: Your detail biscuit joiner should never be connected to power supply when you are assembling parts, making adjustments, assembling or removing blades, cleaning or when not in use. Disconnecting your detail biscuit joiner will prevent accidental starting that could cause serious personal injury.
Page 8 1 2 1 2 3 3 0 5 16 3 4 45 ° 90 ° 0 5 16 3 4 45 ° 90 ° FEA TURES KNOW YOUR DETAIL BISCUIT JOINER See Figure 2. Your biscuit joiner has been shipped completely assembled and ready for use. An owner's manual and warranty registration are also included.
Page 9 3 2 ADJUSTMENTS W ARNING: If any parts are missing, do not operate tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. DEPTH OF CUT ADJUSTMENTS Your biscuit joiner can be adjusted to three standard cutting depths to accommodate three standard size biscuits — #R1, #R2, and #R3.
Page 10 1 2 1 2 3 3 0 5 16 3 4 45 ° 90 ° 0 5 16 3 4 45 ° 90 ° FENCE ORIENTATION FOR 90 ° ANGLES ADJUSTMENTS FENCE HEIGHT ADJUSTMENT See Figure 5. The fence on your biscuit joiner can be moved up and down to adjust the position of the blade in relation to the top of the workpiece.
Page 11 1 2 3 1 2 3 OPERA TION Fig. 8 Fig. 7 ■ Place the fence against the board and align the indicator marks on the fence with the centerline mark(s) on the board. See Figure 7. ■ Depress the switch trigger and let the motor build to its maximum speed, then gradually push biscuit joiner forward to extend the blade into the wood.
Page 12 OPERA TION BUTT JOINTS See Figure 9. A butt joint is one of the weakest joints in woodworking. This type of joint is mating the end grain of one board with the edge grain of another. The bonding of glue on this type of surface is poor. However, by using biscuits you can create a very strong joint that gives a mortise-and-tenon effect.
Page 13 1 2 3 0 3 4 5 1 6 90 ° 4 5 ° T- JOINT OPERA TION T- JOINTS See Figures 11-15. A T-joint is used when the end of a board is joined to the face of another board as shown in figure 11. Attaching shelves to bookcases and inner support braces to frames are typical applications.
Page 14 CENTERLINE MARK ON WORKPIECE OPERA TION Fig. 16 Fig. 15 FLAT MITER JOINTS BISCUIT CENTERLINE MARK(S) BISCUIT SLOT VERTICAL BOARD TO CUT SLOTS IN VERTICAL BOARDS CLAMP HORIZONTAL BOARD INDICATOR MARK BOTTOM SIDE OF BOTTOM SHOE Fig.
Page 15 0 5 16 3 4 45 ° 90 ° OPERA TION Fig. 17 BISCUIT SLOT CENTERLINE MARK(S) EDGE MITER JOINTS BISCUIT Fig. 18 CUTTING EDGE MITER SLOT FROM LONG SIDE OF WORKPIECE FLAT MITER JOINTS (Continued) .
Page 16 OPERA TION Fig. 19 EXTENSION CORDS The use of any extension cord will cause some loss of power. To keep the loss to a minimum and to prevent tool overheating, use an extension cord that is heavy enough to carry the current the tool will draw. A wire gage size (A.
Page 17 3 2 3 2 MAINTENANCE Fig. 20 Fig. 21 Fig. 22 FRONT BASE BLADE SCREWS (4) BOTTOM SHOE 3 2 BLADE SCREW BLADE INNER BLADE WASHER BLADE FLATS OUTER BLADE WASHER GEAR SPINDLE FLATS GEAR SPINDLE #1 PHILLIPS SCREWDRIVER OR 3/16 in. DIAMETER PIN BLADE REPLACEMENT See Figures 20– 22.
Page 18 3 2 MAINTENANCE W ARNING: When servicing, use only identical Ryobi replacement parts. Use of any other part may create a hazard or cause product damage.
Page 19 Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use.
Page 20 TROUBLESHOOTING A. Biscuit slots are too deep or too shallow. Make fine adjustments to depth setting. See "TO MAKE FINE ADJUSTMENTS" section on page 9. B. Biscuit thickness may be out of tolerance. Compress biscuits in a vise if they are too thick.
Page 21 NOTES.
RYOBI TECHNOLOGIES INC. P.O. Box 910 Cambridge, Ontario N1R 6K2 Phone 1-800-265-6778 RYOBI TECHNOLOGIES INC. 1428 Pearman Dairy Road Anderson SC 29625 Post Office Box 1207 Anderson SC 29622-1207 Phone 1-800-525-2579 OWNER'S OPERA TING MANUAL DET AIL BISCUIT JOINER / DBJ50 DOUBLE INSULA TED 972000-311 10-00 Printed in U.
Een belangrijk punt na aankoop van elk apparaat Ryobi DBJ50 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ryobi DBJ50 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ryobi DBJ50 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ryobi DBJ50 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ryobi DBJ50 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ryobi DBJ50 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ryobi DBJ50 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ryobi DBJ50 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
