Gebruiksaanwijzing /service van het product HT230 van de fabrikant Ryobi
Ga naar pagina of 22
SA VE THIS MANUAL FOR FUTURE REFERENCE Y our rotary tool kit has been engineered and manufactured to our high standard for dependability , ease of operation, and operator safety . When properly car ed for , it will give you years of rugged, trouble-free performance.
2 Introduction ..................................................................................................................................................................... 2 W arranty ..................................................
3 GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below , may result in electric shock, fire and/or serious personal injury . SA VE THESE INSTRUCTIONS WORK AREA Keep your work area clean and well lit.
4 SERVICE T ool service must be perfor med only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury . When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual.
5 SYMBOLS Some of the following symbols may be used on this product . Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the pr oduct better and safer .
6 SYMBOLS SERVICE Servicing requir es extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to the nearest AUTHORIZED SERVICE CENTER for repair . When servicing, use only identical replacement parts.
7 EXTENSION CORDS When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the curr ent the product will draw . An undersized cord will cause a drop in line voltage, resulting in overheating and loss of power .
8 FEA TURES Fig. 1 PRODUCT SPECIFICA TIONS Collet ........................................................................ 1/8 in. Switch ......................................................... V ariable Speed No Load Speed ...................... 10,000-35,000 r/min.
9 FEA TURES KNOW YOUR ROT ARY TOOL KIT See Figure 1. The safe use of this pr oduct requ ir es an unders tand ing of the information on the product and in this operator’ s manual as wel l as a knowl edg e of the pr oje ct you ar e attem pti ng. Bef or e use of this product, familiarize yourself with all operating features and safety rules.
10 OPERA TION Fig. 2 WARNING: Do not allow familiarity with pr oducts to make you ca r eles s. Re memb er th at a ca r eles s fra ctio n of a sec ond is sufficient to inflict serious injury . WARNING: Always wear safety goggles or safety glasses with side shields when operating power tools.
11 OPERA TION ACCESSOR Y CHART Quantity Accessory Application 6 Orange 120-Grit Aluminum Oxide Grinding Wheel Bits Ferrous materials: casting, welds, rivets, rust 4 Green 120-Grit Silicon Carbide Grinding Wheel Bits Non-ferrous materials: stone, ceramics, porcelain, glass 3 3/4 in.
12 OPERA TION WARNING: If you are changing an accessory immediately after use, be careful not to touch the collet, collet nut, or the acces sory with your hands or fingers. Y ou will get burned because of the heat buildup from cutting. Always use the wrench pr ovided.
13 OPERA TION CAUTION: T o prevent damage to the spindle or spindle lock, always allow motor to come to a complete stop before engaging the spindle lock. USING THE MANDRELS See Figures 6 - 8. Three types of mandrels have been included for use with this kit.
14 OPERA TION BALANCING ACCESSORIES For precision work, it is important that all accessories be properly balanced. T o balance an accessory , slightly loosen the collet nut and give the accessory or collet a 1/4 in. turn. Y ou sho uld be able to tel l by the sound and fee l if the acces sor y is running in balance.
15 OPERA TION T o determine the optimum operational speed for different materials and accessories, refer to the Speed Dial Settings table. Look this table over and become familiar with it. The best way to determine the correct speed for work on any material is to practice for a few minutes on a piece of scrap, even after referring to the table.
16 OPERA TING THE ROT AR Y TOOL See Figure 10. Learning to use the rotary tool: Hold the tool in your hand and get used to its weight, balance, and the taper of the housing. This taper permits the tool to be grasped like a pencil. Examine the rotary tool accessories carefully .
17 OPERA TION TELESCOPING TOOL HANGER WITH CLAMP ON BASE See Figure 11. The telescoping tool hanger pr ovides a convenient place to hang the rotary tool while the flex shaft is in use. T o clamp the base to a worktable: T ur n the clamp scr ew counterclockwise to open the clamping area.
18 OPERA TION Fig. 13 T o install accessories into the flex shaft: Unplug the rotary tool. Locate the hole behind the collet nut in the flex shaft body . T ur n the collet nut until the hole in the flex shaft body aligns with the hole visible inside the flex shaft.
19 OPERA TION USING THE PLUNGE CUTTING ACCESSOR Y See Figures 15 - 16. The plunge cutting accessory attaches to the end of the rotary tool. Depth of cut can be adjusted in 1/8 in. increments up to 1 in. T o assemble the plunge cutting accessory: Hold the cup-shaped accessory piece with the cup side facing down.
20 MAINTENANCE Ele ctric to ols use d on fibe r glas s mater ial, wal lbo ar d, spack ling compounds, or plaster are subject to accelerated wear and possible pr emature failur e because the fiber glass chips and grindings are highly abrasive to bearings, brushes, commutators, etc.
21 NOTES.
22 ONE WORLD TECHNOLOGIES, INC. 1428 Pearman Dairy Road, Anderson, SC 29625 Phone 1-800-525-2579 www .ryobitools.com • SER VICE Now that you have purchased your product, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center .
Een belangrijk punt na aankoop van elk apparaat Ryobi HT230 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ryobi HT230 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ryobi HT230 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ryobi HT230 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ryobi HT230 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ryobi HT230 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ryobi HT230 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ryobi HT230 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
