Gebruiksaanwijzing /service van het product RY52003 van de fabrikant Ryobi
Ga naar pagina of 22
OPERA TOR’S MANUAL TP30 GAS PRUNER R Y52003 SA VE THIS MANUAL FOR FUTURE REFERENCE Y our pruner has been engineered and manufactur ed to Ryobi’ s high standar d for dependability , ease of operation, and operator safety . When pr operly cared for , it will give you years of rugged, trouble-fr ee performance.
2 3 n Introduction ..................................................................................................................................................................... 2 � n General Safety Rules .....................................
2 3 WARNING! Read and understand all instructions. Failure to follow all instructions listed below , may r esult in electric shock, fire and/or serious personal injury . READ ALL INSTRUCTIONS n For safe operation, read and understand all instruc- tio ns befor e u sing th is produ ct.
4 5 n Kickback is a dange rous reacti on that can lead to serious injury. Kickback may occur when the moving chain con- tacts an object at the upper portion of the tip of the guide bar or when the wood closes in and pinches the chain in the cut.
4 5 SYMBOLS Gasoline and Oil Use unleaded gasoline intended for motor vehicle use with an octane rating of 87 [(R + M)/2] or higher . This product is power ed by a 2-cycle engine and requir es pre-mixing gasoline and 2-cycle oil. Some of the following symbols may be used on this tool.
6 7 SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the pr oduct to your near est AUTHORIZED SERVICE CENTER for r epair . When servic- ing, use only identical replacement parts.
6 7 FEA TURES Fig. 1 PRODUCT SPECIFICA TIONS Engine Displacement ...................................................................................................................................................... 30cc Bar length ...................
8 9 Fig. 2 CLAMP FLA T WASHER LOCK WASHER LONG BOL T CLAMP SHORT BOL T “J” BARRIER HANDLE WARNING: T o prevent accidental starting that could cause serious personal injury , always disconnect the engine spark plug wire fr om the spark plug when assembling parts.
8 9 n Pull apart the ends of the bracket to expand slightly. n Slide the bracket over the power head shaft immediately behind the “J” Barrier Handle. n Squeeze bracket ends together to retighten. n Reinstall the bolt, lock washer, and hex nut to secure.
10 11 WARNING: Do not allow familiarity with tools to make you care- less. Remember that a car eless fraction of a second is sufficient to inflict serious injury . WARNING: Always wear safety goggles or safety glasses with side shields, a har d hat, and safety shoes when operating tools.
10 11 OPERA TION Fig. 7 CUTTING GUIDE Fig. 6 n Re lea se the tri gge r as s oon as th e cut is comp let ed, al low- ing the engine to idle. If you run the pruner at full throttle without a cutting load, unnecessary wear or damage can occur to the chain, bar, and engine.
12 13 ST OP OPERA TION HALF CHOKE (B) FULL CHOKE (A) RUN (C) CHOKE LEVER Fig. 12 POSITION FOR ST ARTING See Figure 9. Lay the pruner on the ground and ensure that no objects or obstructions ar e in the immediate vicinity . Make sure nothing can come in contact with the bar and chain.
12 13 MAINTENANCE FLA TS APPROX .050 IN. (1.25 mm) Fig. 14 Fig. 13 WARNING: When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust.
14 15 MAINTENANCE REPLACING THE BAR See Figures 15 - 20. WARNING: T o avoid possible serious injury , stop engine before re- placing the bar , chain, or performing any maintenance operation. n Remove the bar nut and drivecase cover. n The bar cont ains a bar stu d slot that fits ove r the bar stud .
14 15 ST OP MAINTENANCE CHAIN OILER See Figure 22. n Use Premium Bar and Chain Oil. It is designed for chains and chain oilers and is formulated to perform over a wide temperature range with no dilution required. n Remove the cap and carefully pour approximately 8 oz.
16 17 MAINTENANCE CHAIN MAINTENANCE See Figure 23. For smooth and fast cutting, the chain needs to be main- tained properly . The following conditions indicate that the chain requir es sharpening: n W.
16 17 MAINTENANCE CAUTION: Dull or impr operly sharpened chain can cause excessi ve engine speed during cutting which may result in severe engine damage. WARNING: Improper chain sharpening increases the potential of kickback. Failur e to replace or repair damaged chain can cause serious injury .
18 19 FUEL CAP WARNING: A leaking fuel cap is a fire hazard and must be replaced immediately . The fuel cap contains a non-serviceable filter and a check valve. A clogged fuel filter will cause poor engine perfor - mance. If performance improves when the fuel cap is loos- ened, check valve may be faulty or filter clogged.
18 19 TROUBLESHOOTING PROBLEM CAUSE REMEDY Engine will not start. No spark. No fuel. Engine is flooded. Starter rope pulls harder now than when new . Check spark. Remove spark plug. Re attach the spark plug cap and lay spark plug on metal cylinder . Pull the starter r ope and watch for spark at spark plug tip.
20 21 W ARRANTY R YOBI TECHNOLOGIES INC. LIMITED WARRANTY FEDERAL AND CALIFORNIA EMISSION CONTROL SYSTEMS NONROAD AND SMALL OFF-ROAD ENGINES The U.S. Environmental Pr otection Agency (EP A), the California Air Resources Board (CARB), and Ryobi T echnologies Inc.
20 21 EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED P AR TS LIST Emissions Parts Inspect Before Clean Every Replace Every Clean Every Each Use 5 Hours 25 Hours or Y early 25 Hours or Y early AIR FIL TER ASSY INCLUDES: FIL TER...........................
983000-637 2-05 OPERA TOR’S MANUAL TP30 GAS PRUNER R Y52003 W ARNING: The engine exhaust from this pr oduct contains chemicals known to the State of California to cause cancer , birth defects or other repr oductive harm. CALIFORNIA PROPOSITION 65 R YOBI TECHNOLOGIES, INC.
Een belangrijk punt na aankoop van elk apparaat Ryobi RY52003 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ryobi RY52003 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ryobi RY52003 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ryobi RY52003 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ryobi RY52003 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ryobi RY52003 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ryobi RY52003 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ryobi RY52003 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.