Gebruiksaanwijzing /service van het product X9G-NAGAV van de fabrikant Sceptre
Ga naar pagina of 22
X9G-NagaV User ’ s Manual.
i FCC Compliance Statement This device complies with part 15 of t he FCC Rules. Operation is subject to the following two conditions: 1. This device may not caus e harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
ii The Federal Communications Commission warns that changes or modifications of the unit not expre ssly approved by the party responsible for compliance could void the user ’s authority to operate the equipment.
iii T ABLE OF C ONTENTS TABLE OF CO NTENTS .......................................................................................... III Your New LCD Monitor 1 Unpacking 1 Identifying Components 3 Ad.
1 Rev.1 The LCD Monitor Your New LCD Monitor Your LCD Monitor has been desi gned to be versatile, ergonomic and user-friendly. The LCD Monitor is capable of displaying most standards, from 640x400 VGA to 1280x1024 SXGA.
2 Rev.1 After unpacking your LCD monitor, make sure the following items are included in the box and are in good condition: • LCD monitor • Power Cord • Monitor-T o-PC Analog signal cable 15pin .
3 Rev.1 Identifying Components A. The LCD Monitor — Front View Figure 1-1: The LCD Monitor Front View 1. Pow er-On Indicator This Circular LED indicator green lit when the power is on and orange lit when the LCD monitor is in power-saving mode. 2. Monitor Stand 3.
4 Rev.1 B. "Hot Keys" for Quick Adjustment of Monitor Settings Figure 1-2: "Hot Keys" 1. Brightness Adjustment "hot key": Press this + button to allow you to adjust the brightness of the LCD Monitor directly Brightness 50 2.
5 Rev.1 Adjusting the Tilting Angle The LCD Monitor’s angle settings range from 0 ° to 10 ° . 10 Figure 1-3: Tilting the Monitor 0 to 10.
6 Rev.1 Connecting AC Power and Video Ca ble Note: Turn off your PC and the LCD monitor before connecting your LCD monitor to the computer. DVI VGA AC-IN AC Outlet (Wall Socket) Computer Power Cord Figure 1-4: The AC Adapter Power Management System This LCD Monitor complies with the VESA DPMS power management proposal.
7 Rev.1 The Display Controls The LCD Monitor’s Control Panel Figure 2-1: The Control Pa nel 1. : Enable the OSD Menu button or / Move the cursor to the left (w hen OSD is enabled) 2. : Move the cursor to the Right ( When OSD is enabled) / Auto-adjustment hot key 3.
8 Rev.1 Adjusting the Monitor’s Display OSD Main Menu 1. Pressing the Y button causes the screen below to appear. 2. Use the Y & Z key to select the desired group, then press – or + key to enter into sub-menu 3. Repeat step 2 to select the changed item, then – or + to change the value.
9 Rev.1 Monitor Adjustment Allow you to adjust the LCD monitor’s display settings. Press the Adjustment control button to display the submenu. Use the Function Select button to select one of the fol.
10 Rev.1 text and graphic display modes. PORT-SELECT: To switch between analog and DVI port for PC signal input EXIT: To exits the Monitor-Control submenu OSD-control The OSD-Control menu lets you adjust the position of the OSD on the screen. Press the Adjustment control button to display the submenu.
11 Rev.1 GRAPHIC-CONTROL: The Graphic-Control option lets you make adjustments that effect the contrast, brightness and color of the LCD monitor’s display. CONTRAST: To adjust the contrast level of the display screen BRIGHTNESS: To adjust the light level on the display screen.
12 Rev.1 To reset the entire Graphic-Control submenu settings to the factory default. EXIT: To exit the Graphic-Control submenu. MISC-CONTROL: The Misc-Control menu option lets you select the OSD display language, adjust the audio volume setting and view system information.
13 Rev.1 Note: 1) No video When the monitor is ON and there is no video signal received, the following message will be displayed 2) Signal out of range When the frequency range of the signal is out of.
14 Rev.1 Appendix A TFT LCD Monitor Specifications Item Specification LCD Panel 19" SXGA Control Functions Power Software Power switch with LED indicator (ON/OFF) Main Menu Submenu MONITOR- CONTR.
15 Rev.1 Item Specificaiton Scanning Frequency H/V, Hz 24-80K 50-75 P o w e r Management M e e t s VESA DPMS Power Consumption (ON/OFF, W) 34W/1W Max. Dimensions WxHxD 16.
16 Rev.1 Appendix B Supported Timing Item Standards Resolution Dot Clock (MHz) Vertical Scanning Frequency (Hz) Horizontal Scanning Frequency (kHz) 1 NEC PC98 640x400 21.05 56.42 24.83 2 MAC 13" mode 640x480 30.24 66.67 35.00 3 MAC 16" mode 832x624 57.
17 Rev.1 Appendix C Troubleshooting This LCD monitor comes pre-adjusted with standard VGA timing. Due to output timing differences among various VGA cards, you may initially experience an unstable or unclear display when a new display mode or new VGA card is selected.
18 Rev.1 Change to one of the alternate m odes listed in Appendix B, or replace the VGA card and repeat steps 1 and 2. 4. If the power LED is not lit, check that the AC power connector is securely connected, and verify that the AC adapter LED is lit. If the AC adapter LED is not lit, please contact your dealer for assistance.
Een belangrijk punt na aankoop van elk apparaat Sceptre Sceptre X9G-NAGAV (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sceptre Sceptre X9G-NAGAV heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sceptre Sceptre X9G-NAGAV vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sceptre Sceptre X9G-NAGAV leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sceptre Sceptre X9G-NAGAV krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sceptre Sceptre X9G-NAGAV bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sceptre Sceptre X9G-NAGAV kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sceptre Sceptre X9G-NAGAV . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
