Gebruiksaanwijzing /service van het product KSD-541 van de fabrikant Seagate
Ga naar pagina of 18
-1- Industrial 5-Port Fa st Ethernet Switche s with SFP Slot a nd option al 4 PoE PSE Ports Ba sic Model: KSD-541 PoE Model: KSD-541-P In stallation Guide DOC.
-2- (C) 2008 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without permission from KTI Networks Inc. KTI Networks Inc.
-3- The information contained in this document is subject to change without prior notice. Copyright (C) . All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. W ARNING: This equi pment ha s been tested a nd found to comply with the li mits for a Cla ss A digital device, pursua nt to Part 15 of the FCC Rules.
-4- T a ble of Contents 1. Introduction .................................................................................................. 5 1.1 Features .................................................................................................
-5- 1. Introduction The switches are 5-port Fa st Ethernet switches which are f eatured with four copper ports a nd one combo port. The combo port comes with one RJ-45 a nd one SFP slot. The SFP slot ca n be mounted with a fiber tra nsceiver optionally to support a fiber connection.
-6- 1.1 Fe ature s Provides 5 10/100Mbps RJ-45 a nd one 100Mbps SFP slot All copper ports support auto-negoti ation a nd auto-MDI/MDI-X detection Provides full wire speed forwarding Supports IEEE 802.
-7- 1.4 Specif ication s Copper Ports w/h PSE (P2-P5) Compli a nce IEEE 802.3 10Ba se-T , IEEE 802.3u 100Base-TX Connectors Shielded RJ-45 ja cks Pin a ssignments Auto MDI/MDI-X detection Configuration Auto-negoti ation T ra nsmission rate 10Mbps, 100Mbps Duplex support Full/Half duplex Network ca ble Cat.
-8- Power over Ethernet Function (PoE Model) PSE Pin 4,5 Positive of power voltage (T ypical 48V DC) PSE Pin 7,8 Negative of power voltage (T ypical 48V DC) Discovery PD resista nce 15K ~ 33K PD Cla ssification Cla ss 0 ~ 4 Power delivery 15.
-9- 2. In stallation 2.1 Un pa cking The product pa ckage contains: • The switch unit • One product CD-ROM 2.2 Safety Cautions T o reduce the risk of bodily injury , electrical shock, fire, a nd da mage to the product, observe the following precautions.
-10- 2.4 Din-Rail Mounting The steps to mount the switch on a Din-rail are: One Din-rail mounting bra cket is provided in the product pa ckage a s shown below: Install the bra cket on the bottom of the switch unit.
-11- 2.5 Pa nel Mounting One pa nel mounting bra cket is provided in the product pa ckage a s shown below: Install the bra cket on the bottom of the switch unit.
-12- Using T erminal Blocks Three terminal conta cts are provided: V dc Positive ( + ) termin al V dc Negative ( - ) termin al Cha ssis ground * Working V dc for general a pplication: +6V ~ +60V DC * Working V dc for PoE a pplication : +43V ~ +54V DC (T yp.
-13- 3. M a king Connection s 3.1 Ma king UTP Conne ction s The copper ports support the following connection type s a nd dista nce s: Network Cables 10BASE-T : 2-pair UTP Cat.
-14- 3.3 Ma king PoE Connection s This section describes how to make a connection between a PSE port a nd a PoE PD device. For the PoE switch model, Port 2, Port 3, Port 4 a nd Port 5 are equi pped with PoE PSE function. The ports are ena bled to deliver power together with network signal to a connected powered device vi a Cat.
-15- 3.4 LED Indication L ED Function State Interpretation POWER Power status O N The power is supplied to the switch. OFF The power is not supplied to the switch. LIN K/ACT Por t l ink status O N A port link is e sta blished. (No traf fic) BLIN K Port link is up a nd there is traffic.
-16- 4. Application s 4.1 Application s with Ba sic Switch Model The following figure illustrates a ba sic switch model connects five computers vi a Cat.5 ca ble s. The following figure illustrates a ba sic switch model connects four computers vi a Cat.
-17- 4.2 Applications with PoE Switch Model The figure below illustrates a PoE switch connects f our PoE IP camera s via Cat.5 ca ble s a nd uplinks to a fiber ba ckbone: The figure below illustrates a PoE switch connects f our PoE WLAN a ccess points vi a Cat.
-18- The figure below illustrates a PoE switch powered by a 48V DC power a da pter connects four PoE medi a converters vi a Cat.5 ca bles a nd uplinks to a fiber ba ckbone:.
Een belangrijk punt na aankoop van elk apparaat Seagate KSD-541 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Seagate KSD-541 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Seagate KSD-541 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Seagate KSD-541 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Seagate KSD-541 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Seagate KSD-541 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Seagate KSD-541 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Seagate KSD-541 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
