Gebruiksaanwijzing /service van het product 139.53535SRT1 van de fabrikant Sears
Ga naar pagina of 40
OWNER'S UAL Model No. 139.53535SRT1 139.53644SRT 139.53647SRT1 For Residential Use Only Caution: Read and follow all safety rules and operating instructions before first use of this product.
Contents Page A review of safety alert symbols ................................. 2 You'll need tools .......................................................... 3 Safety information regarding garage door locks and ropes ...........................
You'll Need Tools During assembly, installation and adjustment of the opener, instructions will call for hand tools shown below. Carpenter's Level Tape Measure Pencit Hack Saw Stepladder Wir.
Before you begin, survey your garage area to see whether any of the conditions below apply to your installation. Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 24 for details.
One-Piece Door without Track Before you begin, survey your garage area to see whether any of the conditions below apply to your installation. Slack in chain tension is normal when garage door is closed. Header Wall FINISHED CEILING Support bracket & fastening hardware is required.
Carton inventory Your garage door opener is packaged in two cartons which contain all parts illustrated below. If anything is missing, carefully check the packing material. Parts may be "stuck" in the foam. Hardware for assembly and installation is shown on page 7.
Separate all hardware from the packages in the rail carton and the opener carton, as shown below, for the assembly and installation procedures. Assembly Hardware i Washered Screw Hex Screw Nut 5/16&qu.
Assembly Section: Pages 8 - 11 To avoid installation difficulties, do not run the garage door opener until instructed to do so. Assembly Step 1 Assemble the T=rail & Attach the Cable Pulley Bracket • Place the 3 T-rail sections on a flat surface for assembly.
Assembly Step 2 install the Trolley on the T-rail * Attach the threaded shaft to the trolley with the lock washer and nuts as shown. Trolley Outer Nut Lock Washer 5/16" Trolley Threaded Shaft Inn.
Assembly Step 4 Install the Chain/Cable & Attach the Sprocket Cover Dispensing Carton Leave Chain and Cable Inside Dispensing Carton to Prevent Kinking. Serious injury can result if fingers become entangled in moving opener sprocket. Attach sprocket cover securely.
Assembly Step 5 Tighten the Chain & Cable • Spin the inner nut and lock washer down the threaded shaft, away from the trolley. • To tighten the chain, turn outer nut in the direction shown.
installation Section: installation Step 1 Determine Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door.
Read the Safety instructions on page 12. They also apply to doors without tracks. * Close the door and mark the inside vertical centerline of your garage door. Extend the line onto the header wall above door. If headroom clearance is minimal, you can install the header bracket on the ceiling.
You can attach the header bracket either to the wall above the garage door, or to the ceiling, Follow the instructions which will work best for your particular requirements.
installation Step 3 Attach the T=rai! to the Header Bracket --Header Wall Header Bracket Cable Pulley Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. if the door spring is in the way you'll need help.
installation Step 4 Position the Opener Follow instructions which apply to your door type as illustrated. A 2×4 laid fiat is convenient for setting an ideal door-to-T=rail distance. • Raise the opener onto a stepladder. You will need help at this point if the ladder is not tail enough.
installation Step 5 Hang the Opener Two representative installations are shown. Yours may be different. Hanging brackets should be angled, Figure 1, to provide rigid support. On finished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener.
installation Step 6 Install the Premium Control Console Locate the door control within sight of the door at a minimum height of 5 feet where small children cannot reach, and away from all moving parts of the door and door hardware. The door control is typically attached directly to the wall.
6.Attach the User Safety Instruction label to the wall near the door control, and the Maintenance Instruction label in a prominent location on the inside of the garage door. Page 32 explains how to use the door control. Do NOT connect the power and operate the opener at this time.
installation Step 9 Electrical Requirements To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will onlyfit into a grounding type outlet. If the plug doesn't fit into the outlet you have, contact a qualified electrician to install the proper outlet.
The Safety Reversing System Information you'll need before you begin the installation of the safety reversing sensor. The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction.
installation Step 10 I install the Safety Reversing Sensor Figures 2 and 3 show assembly of brackets and "C" wrap based on the recommended installation of the sensors as shown on page 21. However, Figures 4 and 5 are variations which may fit your installation requirements better.
* Center each sensor unit in a "C" wrap with lenses pointing toward each other across the door (see Figure 6). Secure sensors with the hardware shown. Finger tighten the wing nut on the receiving eye to allow for final adjustment. Securely tighten the sending eye wing nut.
installation Step 11 Fasten Door Bracket Follow instructions which apply to your door type as illustrated below or on page 25. To prevent damage to steel, aluminum, fiberglass or glass panel doors, always reinforce the inside of the door both vertically and horizontally with an angle iron.
Please read and comply with the warnings and reinforcement instructions on page 24. They apply to one-piece doors also. Header Walt -- Finished Ceiling -- 2x4 Support Header Bracket Door Bracket Place.
installation Step 12 Connect Door Arm to Trolley Follow instructions which apply to your door type as illustrated below and on page 27. Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley.
Assemble the DoorArm: • Fasten thestraight and curved door arm sections together to the longest possible length, with a 2 or 3 hole overlap. • With the door closed, connect the straight door arm section to the door bracket with the 5-16" x 1-1/4" clevis pin.
Adjustment Section: Pages 28 - 30 Adjustment Step 1 Adjust the UP and DOWN Limits Do not make any limit adjustments until the safety reversing sensors are completely installed. Limit adjustment settings regulate the points at which the door will stop when moving up or down.
Adjustment Step 2 I Adjust the Force Force adjustment controls are located on the right side panel of the opener. Force adjustment settings regulate the amount of power required to open and close the door. The door will stop in the up direction if anything interferes with its travel.
Adjustment Step 3 Test The Safety Reversing Sensor • Press the remote control push button to open the door. • Place the opener carton in the path of the door. • Press the remote control push button to close the door. The door will not move more than an inch, and the opener light(s) will flash.
iMPORTANT SAFETY iNSTRUCTiONS To reduce the risk of severe injury or death to persons: 1. READ AND FOLLOW ALL iNSTRUCTiONS. 2. Do not permit children either to operate or to play with the opener. Keep remote control in a location inaccessible to children.
Operation of Your Opener Activate the opener with any of the following: • The Remote Control: Hold push button down until the door starts to move. • The Door Control: Hold push button down until the door starts to move.
Receiver and Remote Control Programming To comply with FCC rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery THERE ARE NO OTHER USER SERVICEABLE PARTS.
Having a Problem? Situation Probable Cause and Solution The opener doesn't 1. Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light, operate from either check the fuse box or the circuit breaker. (Some outlets are controlled by a door switch.
Having a Problem? (continued) Situation Probable Cause & Solution The door opens but 1. If the opener lights blink, check the safety reversing sensor. See page 23. won't close: 2. If the opener lights do not blink and it is a new installation, check the down force.
Repair Parts Rail Assembly__Parts _ J_i 3 J 4 7 5 4 1 1A995 Master link kit 2 41A3489 Complete trolley assembly 3 1B3117 T-rail - center section 4 183Bl10 T-rail- end section 5 41B2616 Cable pulley bracket assembly 6 41A3473 Chain and cable 7 83A4 Rail grease NOT SHOWN 41A3534 Rail assembly hardware kit (includes hardware illustrated on page 7).
Repair Parts Opener Assembly PaNs I 2O 19 18 I 5 17 __ 16 15 13 14 I 7 D 8 i i,,_ (Down) LIMIT SWITCH Brown Contact ASSEMBLY Wire _/'1_ Drive_ Gear , _ Center Lirnit (Up) _ Yellow Contact Contact Wire KEY PART KEY PART NO. NO. DESCRIPTION NO. NO.
Accessories Sears offers many useful accessories for your garage door opener. They are illustrated below with Sears model numbers and descriptions. 139.53702 f 139.53703 139.53704 139.53705 53885 139.53709 Emergency Key Release: Required for a garage with NO access door.
index Access Door/Outside Key Release Accessory ............................................................................................... 4, 5 Chain Tension ........................................................................................
OWNER'S MANUAL Model No. 139.53535SRTI 139.53644SRT 139.53647SRTI The model number label is located under the light lens on the left side panel of your opener.
Een belangrijk punt na aankoop van elk apparaat Sears 139.53535SRT1 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sears 139.53535SRT1 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sears 139.53535SRT1 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sears 139.53535SRT1 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sears 139.53535SRT1 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sears 139.53535SRT1 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sears 139.53535SRT1 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sears 139.53535SRT1 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
