Gebruiksaanwijzing /service van het product 200.71226 van de fabrikant Sears
Ga naar pagina of 16
OWNER'S MANUAL Microprocessor Controlled, Fully Automatic Operation Battery Charger with Engine Starter Plus Battery and Alternator Tester 2=AIVlP SLOW CHARGE 15=AMP FAST CHARGE 40-AMP RAPID CHARGE 125=AMP ENGINE START FOR 12=VOLT BATTERIES Model No.
WARRANTY ................................................................................................................ 2 IMPORTANT SAFETY INSTRUCTIONS ................................................................... 3 PERSONAL SAFETY PRECAUTIONS .
WARNING = RISK OF EXPLOSIVE GASES WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BAT- TERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR CHARGER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.
Never place charger directly above battery being charged. The gases from the battery wilt corrode and damage the charger. Never touch the battery clamps together when the charger is on. You could cause a spark. Never operate charger ifit has received a hard blow, been dropped, or otherwise damaged.
PLUGGING IT IN Your charger requires a 120V AC 2-prong wall outlet receptacle installed according toalllocal codes and ordinances. It is important tounderstand your charger's requirements. This section will tell you about your charger's electrical requirements and how to prepare a battery forcharging.
NOTE: A marine (boat) boat battery must be removed and charged on shore. To charge it on board requires equipment specially designed formarine use. IMPORTANT: Follow all safety instructions and precautions when charging your bat- tery. Wear complete eye protection and clothing protection.
CHARGING BATTERY REMOVED FROM THE VEHICLE: POSITIVE NEGATIVE BATTERY BATTERY _CHARGER POWER 24", 6 GAUGE CABLE GROUNDED POWER OUTLET 1. Note the polarity of the battery posts by checking the identification marks on the battery: POSITIVE (POS, P or +) and NEGATIVE (NEG, N or-).
in seconds. It starts at 5 and counts down to 0. 3. Cool Down - After cranking, the char- ger enters a mandatory 3-minute (180 second) cool down state. During this period, no settings can be changed. The buttons are ignored. The digital display indicates the remaining cool down time in seconds.
If the charge mode is changed after charg- ing has started (by pressing the CHARGE RATE or CHARGE TYPE button), the charging process wilt berestarted. The voltage displayed during charging is the charging voltage and usually will be higher than the battery's resting voltage.
71226 CONTROL PANEL GUIDE MODE OF OPERATION Initial power-up, battery not detected No battery or reversed battery detected Battery tester activated Battery tester with charged battery Battery tester w.
OVERVIEW This battery charger has a built-in battery tester that displays either an accurate battery voltage or an estimate of the battery's relative charge based on the battery voltage and the Battery Council International scale. TESTING SEQUENCE There are four basic steps required to use the 71226 as a battery tester.
This battery charger has a built-in alter- nator tester that displays either an accu- rate alternator voltage or an estimate of the alternator's relative output compared tonormal alternators. The Alternator % values displayed should be taken as general reference, not precise diagnosis.
This charger adjusts the charging time in order to charge the battery completely, efficiently and safely. The microproces- sor automatically makes the necessary decisions. However, this section includes guidelines that can be used to estimate charging times.
Read this entire manual before using your charger. The tips below serve only as a guide for specific situations. If your vehicle won't start: You don't need to fully charge a battery to start your vehicle.
Performance problems often can be corrected by the user. Please read through this chart for a possible solution to common problems. PROBLEM POSSIBLE CAUSE SOLUTION The battery is connected The charger is in tester and the charger is on, mode, not charger mode.
This section shows an illustration of your battery charger. Use it to become familiar with part locations and appearance. Replacement Parts List Sears 71226 iTEM DESCRIPTION PART NUMBER 1 Handle Assem.
Een belangrijk punt na aankoop van elk apparaat Sears 200.71226 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sears 200.71226 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sears 200.71226 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sears 200.71226 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sears 200.71226 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sears 200.71226 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sears 200.71226 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sears 200.71226 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
