Gebruiksaanwijzing /service van het product 45-04071 van de fabrikant Sears
Ga naar pagina of 28
Model No. 45-04071 PRINTED IN USA 5.5 HP MO W -N-V A C O WNERS MANU AL CA UTION: Read Rules f or Saf e Operation and Instr uctions Carefully FORM NO . 40510 (4/25/07) the fastest wa y to purc hase par ts www .
2 SAFETY R ULES Remember , an y po wer equipment can cause injur y if operated improper ly or if the user does not understand how to operate the equipment.
3 CART ON CONTENTS CART ON CONTENTS (NO T SHO WN FULL SIZE) 3 4 1 2 5 6 11 12 7 8 13 17 16 24 25 29 23 18 26 27 28 19 20 21 14 15 22 9 10 1. T ailgate 2. Car t Body (2) 3. Car t Cov er 4. Engine 5. T ailgate Reinf orcement Brack et 6. Front P anel 7. Mower Adapter 8.
4 HARD W ARE P A CK NO T SHO WN FULL SIZE A B C J R T U S V W P AA Z CC GG DD HH EE FF JJ KK II Y L M N O D E F G H I Q X BB K.
5 REF . QTY . DESCRIPTION REF . QTY . DESCRIPTION A 1 He x Bolt, 5/16" x 4" T 8 Lock Nut, 1/4" B 5 He x Bolt, 3/8" x 3" U 1 Lock Nut, 5/16" C 1 He x Bolt, 1/2" x 1-1/4" V 4 Flat W asher D 4 He x Bolt, 3/8" x 1" W 2 Spacer E 6 He x Bolt, 1/4" x 1-1/4" X 1 W asher , 7/16" Std.
6 ASSEMBL Y INSTR UCTIONS T OOLS REQUIRED FOR ASSEMBL Y (2) 3/4" Wrench (2) 9/16" Wrench (2) 1/2" Wrench (2) 7/16" Wrench (1) Screwdriv er (1) Pliers Spray adhesive is recommended for easier assembl y! 1. Rem ov e the hard ware pa ck and all loose parts from the carton.
7 9. Assemble the front panel over the opposite end of the car t using f our 1/4" x 3/4" hex bolts and 1/4" nylock nuts as shown in gure 4.
8 AXLE REAR T ONGUE LA TCH ST AND BRA CKET 15 . T o pre vent accidental tipping during the follo wing assemb ly procedu res, lo wer the cart to rest upside down on its top anges, so that the wheel suppor t is facing up . See gure 9. 16. Lay the dra wbar tongue onto the Wheel Suppor t and the Latch Stand Brac ket.
9 3/8" x 1" HEX BOL T 3/8" x 3" HEX BOL T 3/8" NYLOCK NUT FIGURE 14 24. Assemble the engine to the tongue using two 3/8" x 3" he x bolts in the rear holes, two 3/8" x 1" hex bolts in the front holes and f our 3/8" nylock nuts .
10 29. Assemble the hitch plate to the tractor hitch if: a. Y our tractor has a square (straight) hitch frame , to help pre vent binding. b . Y our tractor has a lightweight hitch fr ame that needs reinf orcement for towing. Use a 1/2" x 1-1/2" hex bolt, a 7/16" at washer and a 1/2" lock n ut.
11 2. Slide two of the low er suppor t rods through the center loops located in the top of the car t co ver as shown in gure 20. 3. Slide the last lower suppor t rod through outer edge of the car t cover . The bend in the rod must f ace in the direction shown in gure 21.
12 1/4" x 3/4" HEX BOL T 1/4" LOCK NUT 1/4" x 3/4" HEX BOL T 1/4" LOCK NUT 2ND ROD 3RD ROD 1/4" x 1-1/4" HEX BOL T 1/4" LOCK NUT 8. Attach the low er suppor t rod closest to front suppor t tube to the outside of the top angle suppor t using two 1/4" x 3/4" he x bolts and 1/4" loc k nuts.
13 1/4" x 3/4" HEX BOL T 1/4" NYLOCK NUT 1/4" W ASHER 1/4" W ASHER 1/4" x 1" HEX BOL T #10-32 x 5/8" TRUSS BOL T ROPE SECURE ROPE KNO T #10-32 NYLOCK NUT CLIP 11. Place the top angle suppor t and car t bag ontop of the car t as shown in gure 27.
14 1/4" DO WN Keep cut-off as close to the top edge as possible. IMPORT ANT: 1/2" FROM FR ONT MO WER DECK DECK AD APTER NO TE: Make sure adapter c lears gauge wheels on mower dec k Curl on d.
15 AD APTER BRACKET 5/16" flat washers used as needed for shims to adjust for variations in dec ks. (2) 5/16" NYLOCK NUTS 5/16" x 1-1/4" HEX BOL T (2) 5/16" FLA T W ASHERS (3).
16 BEFORE ST ARTING • Y our V ac Sys tem en gine is shi pped witho ut oil o r ga solin e. Ser vice the engine with oil and gas as instr ucted in the separate engine manual. • Inspect the V ac System to make sure all covers (rear door , vinyl boot, elbow , hose adapter , hose and deck adapter are properly attached.
17 HO W T O ST ART Y OUR V A C SYSTEM • Check oil and gas in V ac engine. • Attach spark plug wire to spar k plug. • Mov e choke le ver on engine to CHOKE position. (A warm engine may not require choking.) • Mov e throttle control lev er on engine to F AST position.
18 MAINTENANCE Ser vice Dates Check f or loose fasteners X Check co v er X Check tire pressure X Check engine oil le vel X Lubricate X Clean X X Maintain engine per instructions below and in engine manual.
19 PROBLEM POSSIBLE CA USE(S) CORRECTIVE A CTION Engine f ails to star t 1. Spar k plug wire disconnected. 1. Connect wire to spar k plug. 2. Safety s witch not contacted. 2. Correctly install hose adapter nozzle. 3. Fuel tank empty , or stale fuel. 3.
20 CAR T REP AIR P AR TS FOR 45-04071 5.5 HP MO W -N-V A C 6 19 31 7 19 20 4 15 15 17 A 16 16 2 9 6 A 15 16 10 12 1 28 29 27 3 16 5 16 17 18 15 1 18 8 21 13 26 23 23 14 30 22 11 25 25 24 23.
21 REP AIR P ARTS LIST FOR 45-04071 5.5 HP MO W -N-V A C the fastest wa y to purc hase par ts www .speedepar t.com REF . NO . P ART NO . QTY . DESCRIPTION 1 23912 2 Car t Body 2 24906 1 F ront Panel 3.
22 40 1 17 23 23 14 11 5 8 13 8 13 13 8 27 27 27 27 27 25 25 25 25 31 31 31 12 12 12 34 32 33 34 35 41 36 AD APTER #62468 13 20 21 42 25 25 4 4 38 37 39 4 3 19 18 12 42 18 18 13 25 25 19 19 3 2 42 18 .
23 REF . NO . P ART NO . QTY . DESCRIPTION 1 25836 1 T op Support Angle 2 25740 1 F ront Suppor t T ube 3 25876 2 Brace 4 49864 3 Low er Suppor t Rod 5 43840 2 He x Bolt, 5/16-18 x 1-1/4" 6 49865 1 Car t Cov er 7 1 2 6 30 20 12 7E 1 1 Engine, 5.
24 2 2 2 5 3 5 10 8 24 4 3 17 8 7 16 11 9 20 22 4 21 16 15 16 13 14 1 15 6 12 19 23 24 4 9 2 10 2 18 REF . NO . P ART NO . QTY . DESCRIPTION 1 6 2 9 - 0 2 4 1 a 1 Har ness, Wire 2 24634 1 Housing Asse.
25 SLOPE GUIDE (Keep this sheet in a saf e place for future reference.) Use this guide to determine if a slope is safe for the operation of y our tractor and V ac. Refer also to the instructions in y our vehicle owner s manual. CA UTION: DO NO T OPERA TE Y OUR TRA CT OR AND CAR T ON A SLOPE IN EXCESS OF 10 DEGREES.
26 NO TES.
27 NO TES.
28 © 2006 Agri-F ab , Inc. the fastest wa y to purc hase par ts www .speedepar t.com REP AIR P ARTS Agri-F ab , Inc. 809 South Hamilton Sulliv an, IL.
Een belangrijk punt na aankoop van elk apparaat Sears 45-04071 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sears 45-04071 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sears 45-04071 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sears 45-04071 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sears 45-04071 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sears 45-04071 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sears 45-04071 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sears 45-04071 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
