Gebruiksaanwijzing /service van het product DieHard 200.71460 van de fabrikant Sears
Ga naar pagina of 15
SEA/RS OWNER'S MANUAL Model No. 200.71460 CAUTION: Read and Follow All Safety Rules and Operating Instructions Before Every Use of this Product. h__ 60/20/2 AMP MANUAL BATTERY CHARGER 250/125 AMP ENGINE STARTER with BATTERY TESTER Sears, Roebuck and Co.
Table Of Contents Warranty .................................................................. 1 Important Safety Instructions .................................. 2 Parts ......................................................................... 3 Before Using Your Battery Charger .
Important Safety Instructions - SAVE THESE INSTRUCTIONS - • Read all instructions and cautions printed on the battery charger, battery, and vehicle or equipment using battery. • Use charger only on lead-acid type rechargeable batteries, such as those used in cars, trucks, trac- tors, airplanes, vans, RV's, trolling motors, etc.
Parts The exploded view of your charger shows parts, their location, and a keyed chart identifying each part by name and pert number. The wiring diagram provides additional reference for the professional repair person.
Before Using Your Battery Charger It is important to prepare your charger for use. This section will tell you how to assemble the charger, ground and connect the power cord, and prepare to charge a battery. Assembling your charger It is important to fully assemble your charger before use.
3. Tap the other axle cap onto the opposite end of the axle and place the axle assembly onto the bottom of the charger. Place one end of the bracket into slot, then place the axle assembly under each bracket. Fasten the other side of the brackets using the two 10-32 screws provided.
A TEMPORARY adapter may be used to connect the charger to a two-pole outlet if a properly grounded outlet is not available. Use the adapter ONLY until a properly grounded outlet can be installed by a qualified electrician. DANGER: Before using an adapter as illustrated, be certain that the center screw of the outlet plate is grounded.
Using Your Battery Charger To obtain the best results from your battery charger, you must know how to use it properly. This section will tell you how to set the controls, and how you can charge a battery while it is still in the vehicle, or you can remove it and then charge it.
VOLTMETER: For an accurate reading of your battery's voltage before you begin charging it, use the voltmeter as follows: 1. Set the timer to the OFF position, turn the voltage selector switch to .
Charging Your Battery Charging your battery in the vehicle: 1. Arrange the power cord and charging leads care- fully in order to avoid damage that could be caused by the hood, door, or moving engine parts. 2. Keep clear ofthe fan blades, belts, pulleys, and other parts that can cause injury.
11. When the battery is fully charged, first unplug the charger's powercord. Next, turn thetimerswitch to the OFF position. Then, standing away from the battery, remove the charger clamps in this order: (1) from the chassis connection and, (2) from the battery post.
Calculating charge time The Chart Method Use the following table to more accurately determine the time it will take to bring a battery to full charge. First, identify where your battery fits into the chart. • Small batteries-- motorcycles, garden tractors, etc.
Using the engine start feature Your battery charger can be used to jump-start your car if the battery is low. Follow these instructions on how to use the engine start feature.
Troubleshooting Performance problems often result from little things that you can fix yourself. Please read through this chart for a )ossible solution if a problem occurs. PROBLEM POSSIBLE CAUSE SOLUTION/REASONS No reading on the Clamps are not making a Check for poor connections to battery and frame.
SEAR8 OWNER'S MANUAL Model No. 200.71460 When requesting service or ordering parts, always provide the following information: • Product Type • Model Number • Part Number • Part Descriptio.
Een belangrijk punt na aankoop van elk apparaat Sears DieHard 200.71460 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sears DieHard 200.71460 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sears DieHard 200.71460 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sears DieHard 200.71460 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sears DieHard 200.71460 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sears DieHard 200.71460 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sears DieHard 200.71460 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sears DieHard 200.71460 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
