Gebruiksaanwijzing /service van het product PRECISION FB 380 van de fabrikant Seiko
Ga naar pagina of 50
SEIKO Precision FB – 380 Dot-Matrix Flatbed Printer USER MANUAL.
i Import ant Safety Instructions 1. Read all of these instructions carefully and thoroughly and save them for later reference. 2. Follow all warnings and instructions in the manual as well as marked on the product. 3. Unplug this product from the power outlet before cleaning.
ii T able of Content s Chapter 1 Overview .............................................................................................................. 1 Features .......................................................................................
iii Chapter 4 Printing from Y our Software .................................................... 14 Setting Up Y our Printer T o W ork W ith Software .............................................. 14 Chapter 5 Control Panel ............................
iv Specifications ............................................................................................................................... . 28 General ............................................................................................
1 Chapter 1 Overview Features Thank you for purchasing this SEIKO Precision FB-380 printer . Combing high speed, high quality output with adv anced paper handing capabilit ies, this versatile, 24-pin, flatbed printer is ideal for a wide range of multi-part and cut-sheet printing requirements.
2 Automatic Interface Sw itching The FB-380 is equipped with two interface connectors and therefore accepts both parallel (Centronics) and USB data transfer . The printer aut omatically detects the type of data transfer received from the host computer and switc hes to the corresponding interface type.
3 Chapter 2 Preparation Unp acking Check each item against the following packing list, if any of these it ems are missing, please contact your dealer .
4 Part s Identification Figures 2-2 and 2-3 highlight the main components of the printer . Figure 2-2 Main parts of printer (front view) A Window cover G Ribbon cassette cartridge B Control panel H Pr.
5 Inst allation Before placing the printer in your chosen location, consider the following guidelines: This printer should be placed on a normal table or desk. Be sure that the surface is level, to avoid an uneven load on the carriage as it operates.
6 3 Pull the Sub friction roller unit by gripping the center area of the unit by your forefingers. Then lift it up until the unit is positioned on the t op of printer a s shown in Figure 2-6. Figure 2-6 Opening the sub friction roller unit 4 If necessary , centre the print head by hand.
7 Connecting the Interface Cable Connect the parallel or USB interface c able as shown in the figure 2-8 below: Caution Make sure that the power switc hes of both printer and host computer are turned OFF b efore you connect the parallel interface cable.
8 T urning the Power on and off T o turn the printer ON, press the I mark on the power switch. T o turn the printer OFF , press the O mark on the power switch.
9 Chapter 3 Loading Paper Paper Thickness Adjustment Before loading cut sheet or tractor pa per , you have to adjust the gap adjust lever on the right of the printer . T o feed thicker papers through the printer , you need to move the gap adjust lever from its st andard position.
10 Loading Cut Sheet s 1 T urn the printer on. 2 Set paper select lever toward the ba ck of printer as shown in Figure 3-2. Figure 3-2 Setting the paper select lever 3 Position the left hand cut sheet guide by referring to the marking on the window cover .
11 5 After the above steps, the printer is ready to print. Using T ractor Paper This printer feeds tractor paper from the rear of the printer to the front. Figure 3-5 Feeding direction of tractor paper Loading T ractor Paper 1 T urn the printer on. 2 Set paper select lever toward the front of printer as shown in Figure 3-6.
12 Figure 3-7 Setting tractor paper into the tractor 5 Release the lock lever of the right tractor and open the tractor p aper guide. Place the paper on the sprocket pi ns, then close the paper guide.
13 7 Align the paper with the print start position. Ensure the tractor paper is in line with t he print start position. If the paper is not aligned with the print start position, releas e the tractor lock levers of the left and right tractors, align the paper , and then fa sten the lock lever to lock the tractors.
14 Chapter 4 Printing from Your Software Setting Up Y our Printer T o W ork With Sof t ware The printer supports Epson ESC/P2 emulation. Y ou can select the Ep son LQ-570+ driver for this printer , but the best way to ensure that all the features on your printer are supported by the software is to use the SEIKO Precision printer driver .
15 Chapter 5 Control Panel Control Panel Keys and LEDs The control panel consists of four keys and three LEDs as shown in Figure 5-1 Figure 5-1 The printer control p anel The following table details eac h indicator LED function: LED Indicator On Off POWER (green) Lights when the printer is turned on.
16 Basic Control Panel Operations Y ou can use the four keys on the control panel to operate your printer . ONLINE Pressing the ONLINE button, toggles between ONLINE and OFFLINE mode.
17 LF/FF: Decrease the top of form by 1/60 in ch. Y ou can decrease the margin to a maximum of -10 (-10/60 inch) from the default setting. T o exit and save your new setting, press the ONLINE button. The POWER LED and ONLINE LED blink simultaneously 3 times with a beep, then the POWER LED will be on.
18 T o enter the Setup Menu System and change the settings 1. Lift the window cover of the printer . 2. Eject any paper currently in the printer (or p a rk tractor paper) then switch the printer online. 3. Keep pressing the P ARK/LOAD key for 3 seconds.
19 The printer automatically loads paper and prints the current settings. An example print out is shown in Figure 5-2..
20 Figure 5-2 Current Setting Report SEIKO Precision FB-380 Current Setting Report Current settings are FILLED . PRINT STYLE FONT ROMAN PITCH 10 CPI P AGE LA YOUT LINE SP ACING 6 LPI FORM LENGTH A 4 P AGE SKIP OFF COMPRESS PRT NORMA L PRINT MODE TEXT DIR BI-DIR GRAPHIC DIR UNI-DIR CHARACTER SLASH ZERO OFF CHARACTER SET GRAPHICS INTL CHAR SET U.
21 Options of the Setup Menu System The following printout in Figure 5-3 shows the selections from the Setup Menu System and is followed by a description of how to use it in T able 5-2 (Options of the Setup Menu System).
22 Options Description FONT Set the font for the printer to use in the absence of any font control instructions from your software. PITCH Set the pitch to deter mine the horizontal spacing of the printed characters. LINE SP ACING Set the vertical spacing of the pr inted characters.
23 Restoring Factory Printer Settings Y ou can restore to the factory printer settings without having to work through the Setup Menu System to reset the menus. T o restore to the factory settings: 1. Make sure that the printer is ONLINE 2. Press and hold down the ONLINE and COPY keys on the control panel for 3 seconds.
24 Hex Dump Mode T urning power on while pressing the P ARK/LOAD key causes the printer to enter Hex Dump mode. In this mode, if y ou execute the following program ： 10 LPRINT CHR$(27); “ 4 ” .
25 Appendix A Maintenance and Fault Finding Introduction Y our printer requires very little routine maintenance. In fact, the best maintenance for the printer is preventative. If you have follow ed the suggestions for locating it in an area free of excessive dust and heat it will give you a l ong and trouble-free performance.
26 Cleaning the platen Clean the platen with a soft cloth. Intervals and Materials for Cleaning Clean inside the printer in accordance with the following: Ribbon Cartridge The inked ribbon in the cartridge is a continuous loop and will print several million characters before needing replacement.
27 Characters On The Screen Don’t Match The Printed Characters Many graphics characters and special symbols are produced by different ASCII codes on each make of computer and printer . Compare the character set charts in your com puter manual with the printer character sets.
28 Appendix B S pecifications General T ype 24-Pin Flatbed Dot Matrix Impact Printer Fonts 1 DP (Draft) 7 LQ (ROMAN, SANSERIF , COURIER, PRESTIGE, SCRIPT , OCRA, OCRB) Emulation Epson ESC/P2 Memory 256K bytes (*Input buffer: 132K bytes) Interface Parallel Interface ： Centronics (IEEE 1284 NIBBLE mode Compatible) USB Interface ： USB 2.
29 Mechanism Mode 10 CPI 12 CPI 15 CPI 250CPS 300 CPS 375 CPS DP 120 DPI 120 DPI 120 DPI 83 CPS 100 CPS 125CPS Print speed LQ 360 DPI 360 DPI 360 DPI Paper slew speed (Continuous feed): 5.
30 Print mode specifications Print mode Multipart mode Dot Spacing (V × H inches) Max No. of Columns Character S tructure (V × H) Printing Speed (cps) Normal 83 Dark 1 66 Dark 2 53 10cpi Dark 3 1/18.
31 Graphic Print Specifications Graphic type Density Pins Horizontal dot pitch Multipart mode Print speed (inch/second) Normal 、 Dark 1 9.9 Dark 2 8 120dpi 24 1/240 inch Dark 3 3.9 Normal 、 Dark 1 6.6 Dark 2 5.3 180dpi 24 1/360 inch Dark 3 2.6 Normal 、 Dark 1 6.
32 USB Interface USB 2.0 Full-S peed. The following table provides the standardized contact termi nating assignments by number and electrical value for Series “A” and Series “B” connectors.
33 Name Code (Symbol) Code (Hex.) Code (Dec.) Set Left Margin ESC l 1B h 6C h 27 d 108 d Horizontal T ab HT 09 h 9 d Set Horizontal T ab Positions ESC D 1B h 44 h 27 d 68 d Set Character S pace ESC SP.
34 Name Code (Symbol) Code (Hex.) Code (Dec.) Select Character T able ESC t n 1B h 74 h 27 d 11 6 d Enable Character Set 2 ESC 6 1B h 36 h 27 d 54 d Cancel command ESC 6 ESC 7 1B h 37 h 27 d 55 d Assi.
35 Select Code Pages Format ESC (t n1 n2 d1 d2 d3 (n1=3, n2=0, d1=0,1,2,3) Code No. d2 d3 (HEX) Name 437 1 0 U.S.A. 437GR 1 10 GRK 437 858 3 0 MUL TI 851GR 4 0 GRK 851 857 5 0 TURKEY 855 6 0 CYRILLIC .
.
.
.
.
.
.
.
.
36 This printer complies with t he regulation about the maximu m noise level in the work place – 3. GPSGV , under which the highes t noi se level has to be 70 dB (A) or less in accordance with ISO7779. Maschinenlärminformations-V erordnung - 3. GPSGV , der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäß ISO7779.
Company name ： SEIKO PRECISION (Europe) GmbH Addr ess ： Hermann-Buck-W eg 9, D-22309 Hamburg , Germany.
Een belangrijk punt na aankoop van elk apparaat Seiko PRECISION FB 380 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Seiko PRECISION FB 380 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Seiko PRECISION FB 380 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Seiko PRECISION FB 380 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Seiko PRECISION FB 380 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Seiko PRECISION FB 380 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Seiko PRECISION FB 380 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Seiko PRECISION FB 380 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
