Gebruiksaanwijzing /service van het product AR-PB8 van de fabrikant Sharp
Ga naar pagina of 32
CODE: 0 0ZARPB8//A1E DIGIT AL COP IER OPTION P RINTER EXP ANSION KIT MODEL AR- PB 8 Part s mark ed w ith “ ” i s impo rtant for m aintai ning the safety of t he se t. Be s ure t o r eplace thes e par ts wit h speci fied ones for maintaining the safety and performance of the set.
AR-PB8 CONTENTS [ 1 ] SYSTEM CONFIGURATION . . . . . . . . . . . . . . . 1-1 [ 2 ] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1 . Basic specif icat ions . . . . . . . . . . . . . . . . . . . . . . 1-1 2 . Printer dri ver spe cifica tion s .
[1] SYSTEM CONFIGURATION [2] SPECIFICATIONS 1. Basic specifications LCD panel kit PS2 e xpansion kit Printer expansion kit Expansion memor y (Commercially av ailab le 168 pin EDO DIMM: 16MB/32MB/64MB).
Item Contents Interface select Auto Emulation select Auto Plug and play Conforming (only with Windows 95/98) Printer driver Microsoft Windows 3.1 ∗ A Microsoft Windows 95 Microsoft Windows 98 Microsoft Windows NT4.
D. Option (1) LCD kit AR-PA1 Key 6 pcs. (LINE, MENU, ITEM, ← , → , ENTER) Lamp 2 (DATA, ONLINE) Display 20 digits × 2 lines ∗ When installing the AR-PB8 to a model which is not equipped with the LCD panel, the LCD kit (AR-PA1) must be installed to.
(2) Network board 10/100 Base TX TCP/IP, IPX/SPX, Ether Talk, Jet Admin ∗ A 10 Base 2/T TCP/IP, IPX/SPX, Ether Talk, Jet Admin ∗ A (3) PS kit ∗ A Model name AR-PS1 Page description language Post.
(2) Paper feed port Tray kind Bypass Tray Tray 1 Tray 2 Tray 3 Tray 4 Capacity 100 sheets 250 sheets 250 sheets 250 sheets 250 sheets A3 B4 A4 A4R B5 B5R A5 A5R Ledger Legal Letter LetterR Invoice InvoiceR Foolscap Folio Executive COM-10 C5 DL Custom ∗ The number of trays supported depends on each model.
H. Print Area Paper size A BCDE FGH A3 7014 9920 6730 142 100 300 6814 0 B4 6070 8597 5786 142 100 300 5870 0 A4 4960 7014 4676 142 100 300 4760 0 B5 4298 6070 5770 142 100 300 4098 0 A5 3508 4960 322.
I. Print reference This machine employs the center reference system. Since the digital copier is not equipped with the paper size detection, format is made not by the actual paper size but by the paper size specified by the computer, and center distribution is made.
[3] SET UP 1. Procedures on the copier (operation panel) ∗ When installing the LCD panel kit simultaneonsly. A. Copier operation panel disassembly • Remove screws and connector, and remove the operation panel. B. Cover disassembly • Remove screw and disengage pawls, and remove the cover.
B. Copier shield plate disassembly • Remove screws, and remove the shield plate. C. PWB fixing plate installation • Fix the plate with screws. D. Printer PWB installation • Fix the printer PWB with screws. • Before introduction of the Expansion memory, the PS PWB, or the network PWB, this procedure must be performed.
G. PWB cover installation • Install the PWB cover with screws. 3. Expansion memory installation • Fix the memory PWB with pawls. 4. PS kit (AR-PS1) installation • Fix the PS PWB with pawl. ∗ Note: The DIMM connector and the PS-PWB are provided with the reverse insertion protection key(notch).
6. INSTALLING THE PRINTER DRIVER To use this printer with your computer, you must install the printer driver. Install the printer driver using the supplied SHARP Software CD- ROM. This kit is supplied with the following printer drivers: • PCL6 for Windows 95/98 • PCL6 for Windows NT 4.
6) Print a test page by clicking the [Finish] button. Note: If you check “No” and click the [Finish] button, the printer does not print a test page after the installation. • The printer driver installation begins. • If the “Insert Disk” window appears, perform the following steps: <1> Click the [OK] button.
C. Installing onto Windows 95/98 without Using the Plug & Play Function Computers using Windows 95 or Windows 98 that are compatible with plug & play can install the printer driver automatically.
D. Installing onto Windows NT 4.0 1) Turn the computer on and start Windows NT. 2) Click the Start menu, point to “Settings”, and choose “Printers”. 3) When the “Printers” window appears, double-click the “Add Printer” icon. 4) Choose “My Computer” or “Network printer server” and click the [Next] button.
[4] SETTING AND ADJUSTMENTS 1. Configuration setting (Basic Menu Setting Procedure) Note: The menus and items displayed may be different depending on the optional functions installed. 1) When the printer is not in use, press the ON LINE key to put the printer off-line.
DATA LINE MENU ITEM ENTER DATA NE MENU ITEM ENTER 4) Press the Left or Right arrow key to change the setting. • The current value is marked with an asterisk ( ∗ ). 5) After choosing the required value, press the ENTER key. • The new value is registered.
[5] SIMULATION 1. Entering the simulation mode Perform the following procedure to enter the simulation mode. Clear key → Interruption key → “0” key → Interruption key → Main code → Start key → Sub code → Start key 2. Cancelling the simulation mode When the all clear key is pressed, the simulation mode is cancelled.
[6] CONFIGURATION REPORT AND TEST PAGE To test print the configuration page and font list, use the following procedure: DATA ON LINE MENU ITEM ENTER DATA ON LINE MENU ITEM ENT DATA ON LINE MENU ITEM ENT DATA NE MENU ITEM ENTER 1) Press the ON LINE key to switch the printer to the offline mode.
2. Items and contents A. Hardware status (Machine information) a. Language Value: (English/French/German/Italian/Dutch/Spanish/Swedish) Example: English Default: Depends on the Destination setting Description: Depends on the LCD display, the configuration page, and the font list language.
[7] FIRMWARE VERSION UP 1. Cases where flash memory rewriting is required In the following cases, the program in the printer control PWB flash memory must be rewritten. 1) When a bug or other error is found 2) Data stored in the flash memory is destroyed or deleted.
[8] TROUBLE CODE LIST Main code Sub code Detail of trouble F9 00 Content F9- ∗∗∗ Communication trouble between MCU and PRT. Detail Communication setup error, framing, parity, protocol error Cause Printer PWB connector disconnection Printer unit PWB MCU PWB harness failure Printer PWB mother board connector pin breakage.
[9] CIRCUIT DIAGRAM 1. BLOCK DIAGRAM CPU NR4650 (Internal 133MHz) G/A (1) SYSAD[63:0] SYSCMD[8:0] SYSAD[31:0] SYSAD[53:33] SYSAD[31:0] RAD[21:1] RCS_[3:0] PIACS1_ PIACS0_ MD[63:0] MA[11:0] RAM 8MB RAM DIMM168 64MB Max RAM DIMM168 64MB Max MD[63:0] MBA[11:0] RAS0 CAS[7:0] Digital copier I/F CY2292 14.
2. CIRCUIT DIAGRAM 9 – 2 9 – 3 A B C D E A B C D E 4 3 2 1 4 3 2 1 IC1 NR4650 GND 3 VCC 4 GND 9 SYSAD0 77 GND 15 VCC 10 GND 21 GND 29 VCC 16 GND 35 SYSAD1 72 GND 41 VCC 22 GND 49 INT0_ 89 GND 59 V.
9 – 4 9 – 5 R95 10 R96 10 X2 14.318MHz CY2292 12 IC18 CLKB 9 CLKA 10 10 66 113 GND 11 S0 12 S1 13 VCC 14 SP_ 15 SHUTDN_ 16 CLKC 1 VCC 2 GND 3 XT ALIN 4 XT ALOUT 5 XBUF 6 CLKD 7 CPUCLK 8 R169 R125 10 R138 4.7K R168 4.7K R166 4.7K C13 10u C9 10u C70 0.
9 – 6 9 – 7 R176 10 R223 10 IC21 74LS244 1A1 2 1A2 4 1A3 6 1A4 8 2A1 11 2A2 13 2A3 15 2A4 17 1G 1 2G 19 1 19 18 16 14 12 9 7 5 3 20 10 IC20 74LS244 2 4 6 8 11 13 15 17 1G 1 19 2G 1Y1 18 1Y2 16 1Y3.
9 – 8 9 – 9 4 3 2 1 4 2 1 3 E D C B A E D C B A LDT[15:0] SYSAD[15:0] PIARD_ LDTOE_ MBA[11:0] MA[11:0] MBOE_ MBWE_ MBRAS2_ MBRAS1_ MOE_ MWE_ RAS2_ RAS1_ RAD[21:1] SYSAD[63:0] ROMWE_ BUFDIR ROE_ FWE_ 3.3V 3.3V 3.3V 3.3V 74LVC16245 IC13 74LVC244 IC12 0.
9 – 10 9 – 11 4 3 2 1 4 3 2 1 A B C D E A B C D E CN1 DIMM72 A0 12 A1 13 A2 14 A3 15 A4 16 A5 17 A6 18 A7 28 A8 32 A9 29 A10 31 A11 33 A12 34 A13 36 A14 65 A15 66 A16 67 A17 68 A18 69 A19 70 A20 7.
9 – 12 9 – 13 4 3 2 1 E D C B A 4 3 2 1 E D C B A MD[63:0] CAS5_ CAS4_ CAS7_ CAS6_ CAS3_ CAS2_ CAS1_ CAS0_ MBWE_ MBOE_ MBRAS2_ CAS7_ CAS6_ CAS5_ CAS4_ CAS3_ CAS2_ CAS0_ CAS1_ MBOE_ MBWE_ MBRAS1_ MBA[11:0] CAS7_ CAS6_ CAS5_ CAS4_ CAS3_ CAS2_ MBOE_ MBWE_ CAS1_ CAS0_ RAS0_ 3.
9 – 14 9 – 15 4 3 2 1 E D C B A 4 3 2 1 E D C B A RESET_ DUMMY VDATA_ VDIN_ PIAWE_ EETCS_ VFCLK RESET_ FAULT_ SLCTIN_ INIT_ SLCT PE BUSY ACK_ AUTOFD_ STB_ PDATA[7:0] NETON_ PIARD_ NICCS_ WAIT RAD[21:1] LDT[15:0] STS CRDY_ EREADY_ HSYNC_ RESET_ VDATA_ CMD SRDY_ PAGE_ PREADY_ 5V 3.
COPYRIGHT © 1999 BY SHARP CORPORATION All rights reserved. Printed in Japan. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
Een belangrijk punt na aankoop van elk apparaat Sharp AR-PB8 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sharp AR-PB8 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sharp AR-PB8 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sharp AR-PB8 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sharp AR-PB8 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sharp AR-PB8 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sharp AR-PB8 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sharp AR-PB8 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
