Gebruiksaanwijzing /service van het product AY-X18NCJ van de fabrikant Sharp
Ga naar pagina of 28
Split Type Inverter Room Air Conditioner OPERATION MANUAL MODELS: AY-X09NCJ AE-X09NCJ AY-X12NCJ AE-X12NCJ AY-X18NCJ AE-X18NCJ AY-X24NCJ AE-X24NCJ AY-X28NCJ AE-X28NCJ Thank you for selecting SHARP Air-C onditioner. Please read this manual carefully before operat ion and keep it f or further reference.
2 CONTENTS Operation and maintenance Notice for operation ………………………………………………. 3 Name and function of each part ………………………………… 4 Operation of wireless remote control …………………………… 5 - 8 Emergency operation …………………………………………….
3 Notices for operation Please read the following care fully before operating The product should be installed by a licensed air conditioning contractor in accordan ce with AS/NZS3000:2000 and your electricity supplier’s rules. Th is product is designe d to operate on 220-240VAC, 50Hz.
4 Name of parts NOTE: Actual units might v ary slightly from those shown abov e (1) Power cord (AYX09NCJ and AYX12NCJ only) (2) Remote controller (3) Front panel (4) Filter (5) Horizontal louver (6) W.
5 Operation of wireless remote control Indoor Front Panel Lights : RED powe r light should be on while power is applied. If blinking please call for service. ORANGE = Heat, BLUE = Cool. Note: Be sure that there are no obstructions b etween indoor receiver and remot e control.
6 Operation of wireless remote control con’t. Note: This wireless remote control is universal, and it could be used for various units. Some b uttons on this control may not be applicable to this unit.
7 Operation of wireless remote control con’t. TIMER ON button – selects or presets a time you wish the air conditioner to turn on. Press this button to select TIMER ON setting. Pressing the or button during the first 5 seconds adjusts the time value by one mi nute each time pressed.
8 Operation of wireless remote control con’t. Introduction of Special Function ● Press SLEEP button to select Sleep 1 ( ), Sleep 2 ( ), Sleep 3 ( ), and cancel. Sleep cancel is default setting. ● Sleep 1 in Cool and Dry modes: after one hour, the main unit set ting temperature will increase 1°C.
9 Operation of wireless remote control con’t. Changing batteries and notices (1) Slightly press down and pus h the back cove r of wireless remote controller. (As show in Fig 1.) (2 ) Take out the old batteries. (3) Insert two new AAA1.5V dry batte ries, and pay attention to the polarity.
10 Care and Cleaning ● Disconnect the power supply at the circuit breaker b efore cleaning and maintenance. ● Do not splash water on the units for cl eaning, as el ectric shocks may occur.
11 Troubleshooting Phenomenon Troubleshooting The unit can not be started up: ● Is the power connected? ● Is the power plug loose? (if applicable) ● Is the circuit protection device tripped off?.
12 Operation Tips Operating Temperature Range Indoor side DB/WB (°C) Outdoor side DB/WB (°C) Maximum cooling 32 43 Maximum cooling 21 21 Maximum heating 27 24 Maximum heating 20 -5 The operating temperature range (outd oor temperature) is 15°C ~ 24° C.
13 Notices of Installation CAUTION (1) Before installation, please contact your local aut horised installer. This unit must be install ed by an authorised installer acco rding to local or government regulation s and in compliance with this manual to avoid a malfunction.
14 Notices of Installation con’t. Safety Precautions for Electric Appliances ● A dedicated power supply circuit should be used in ac cordance with local electrical safety regulations. ● Do not drag the power cord. ● The appliance shall be installed in accordance with national wiring regulations.
15 Installation Drawing.
16 Installation of Indoor Unit Earthing Requirements (1) Mounting plate should be install ed hori zontally with slight slant to wa ter tray’s outlet for smooth drainage of water. (2) Fix the mounting plate on the wall wi th screws ensuring good fit to wall stud or masonry.
17 Installation of Indoor Unit con’t Connecting Indoor and Outdoor Electric Wires (1) Open the front panel. (2) Remove the wiring cover co nnect and fix power connection cord to the terminal board as shown in Fig 6. (3) Make the power connection cord pa ss through the hole at the back of indoor unit.
18 Installation of Outdoor Unit Electric Wiring (1) Remove the handle on the right side plate of outdoor unit. (2) Take off wire cord anchorage. Conne ct and fix power connection cord to the terminal board. (3) Fix the power conne ction cord with wire clamps and then connect the correspon ding connector.
19 Check after Installation and Operation Test Check after Installation Items to be checked Possible malfunction Has the unit been fixed firmly? The unit may drop, shake or emit noise Have you done th.
20 Specifications Model AC09RNSYS Function COOLING HE ATING Rated Voltage 200-240V Frequency (Hz) (H/S) 50Hz Total Capacity (W) (H/S/L): Total Capacity (Btu/h) (H/S/L): 3200/2600/570 (W) 10918/8871/19.
21 Specifications Model AC12RNSYS Function CO OLING HEATING Rated Voltage 200-240V Frequency (Hz) (H/S) 50Hz Total Capacity (W) (H/S/L): Total Capacity (Btu/h) (H/S/L): 3900/3500/660 (W) 13307/11942/2.
22 Specifications Model AC18RNSYS Function CO OLING HEATING Rated Voltage 200-240V Frequency (Hz) (H/S) 50Hz Total Capacity (W) (H/S/L): Total Capacity (Btu/h) (H/S/L): 6500/5300/700 (W) 22178/18084/2.
23 Specifications Model AC24RNSYS Function CO OLING HEATING Rated Voltage 200-240V Frequency (Hz) (H/S) 50Hz Total Capacity (W) (H/S/L): Total Capacity (Btu/h) (H/S/L): 8000/7000/1200 (W) 27296/23884/.
24 Specifications Model AC28RNSYS Function CO OLING HEATING Rated Voltage 200-240V Frequency (Hz) (H/S) 50Hz Total Capacity (W) (H/S/L): Total Capacity (Btu/h) (H/S/L): 9000/8000/1000 (W) 30708/27296/.
25.
26.
27.
28 SHARP CORPORATION OF AUSTRALIA PTY. LTD. A.B.N. 40 003 039 405 1 HUNTINGWOOD DRIVE, HUNTI NGWOOD, N.S.W. 2148 P.O. 6827, BLACKTOWN, N.S.W. 2148 www.sharp.net.au SHARP CORPORATION OF NEW ZEALAND LIMITED 59 HUGO JOHNSTON DRIVE, PENROSE, AUCKLAND www.
Een belangrijk punt na aankoop van elk apparaat Sharp AY-X18NCJ (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sharp AY-X18NCJ heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sharp AY-X18NCJ vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sharp AY-X18NCJ leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sharp AY-X18NCJ krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sharp AY-X18NCJ bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sharp AY-X18NCJ kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sharp AY-X18NCJ . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
