Gebruiksaanwijzing /service van het product AS5333 van de fabrikant Acer
Ga naar pagina of 210
i Aspire AS5333/AS5733/AS5733Z SERVICE GUIDE.
ii Revision History Refer to the following t able for the updates made to this service guide. Service guide files and up dates are avail able on the ACER/CSD W ebsite. For more information, go to http://csd.acer .com.tw .The information in this guide is sub ject to change without notice.
iii Conventions The following conventions are used in this manual: W ARNING : ! Indicates a potential for personal injury . CAUTION : ! Indicates a potential loss of dat a or damage to equipment. IMPORT ANT : + Indicate s informati on that is import ant to kn ow for the proper completion of a procedure, choice of an option, or completing a t ask.
iv General Information 0 This service guide provides all technical infor mat ion relating to the basic configuration for Acer global product of fering.
1 CHAPTER 1 Hardware Specifications Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Operating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 CPU and Chipset . . . . .
2 LAN Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-27 Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-28 Hard Disk Drive (AVL components) . . . . . . . . . . . . .
3 CHAPTER 3 Machine Maintenance Procedures Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Recommended Equipment .
4 LCD (Liquid Crystal Display) Module Removal . . . . . . . . . . . 3-37 LCD Module Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39 LCD Bezel Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-40 LCD Bezel Installation .
5 CHAPTER 5 Jumper and Connector Locations Jumper and Connector Locati ons . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Clearing Password Check and BIOS Recovery .
6.
CHAPTER 1 Hardware Specifications.
1-2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Operating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 CPU and Chipset . . . . . . . . . . . . . . . . . . . . .
1-3 Display Supported Reso lution (LCD Supported Resolution) . . 1-32 Graphics Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32 Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4.
Hardware S p ecifications and Configurations 1-5 Hardware Specifications and Configurations Features 0 The following is a brief summary of the co mputer ’s many featur es: Operating System 0 .
1-6 Hardware S pecifications and Configurations Graphics 0 Intel ® HD Graphics with 128 MB of de dicated system memory , supporting Microsoft ® DirectX ® 10 Dual independ ent display support 16.
Hardware S p ecifications and Configurations 1-7 Dimensions and Weight 0 Dimensions 381 (W) x 253 (D) x 25/34 (H) mm (15 x 9.96 x 0.98/1.33 inches) Weight 2.6 kg (5.74 lbs.)10 with 6-cell battery pack Power Adapter and Battery 0 ACPI 3.
1-8 Hardware S pecifications and Configurations Environment 0 Te m p e r a t u r e Operating : 5° C to 35 ° C Non-oper a ting : -2 0° C to 65° C Humidity (non-condensing) Oper.
Hardware S p ecifications and Configurations 1-9 Gaming Oberon Game Zone (except US, Canada, Hong Kong, Korea) WildT angent ® (US, Canada only) Communication and ISP Acer Crystal.
1-1 0 Hardware S pecifications and Configurations Notebook Tour 0 Top View 0 Figure 1-1. T op View T able 1-1. T op View No Icon Item Description 1 Integrated webcam Web ca mera for video communication (only for certain models). 2 Display screen Also called Liqui d-Crystal Display (LCD), displays computer output (Configura tion may vary by models).
Hardware S p ecifications and Configurations 1-1 1 4 Keyboar d For enterin g data into your c omputer . 5 Power indica tor Indicates the computer's pow er status. Battery indicator In dicates the computer's battery status. Charging: The light shows amber when the battery is ch arging.
1-1 2 Hardware S pecifications and Configurations Closed Front V iew 0 Figure 1-2. Closed Front Vie w T able 1-2. Closed Front View No Icon Item Description 1 2-in-1 card reader Accepts Secure Digit al (SD), Multi MediaCard (MMC). NOTE: Push to remove/inst all the card.
Hardware S p ecifications and Configurations 1-13 Left V iew 0 Figure 1-3. Lef t V iew T able 1-3. Left V iew No Icon Item Description 1 DC-in jack Connect s to an AC adapter . 2 External display (VGA) port Connects to a display device (e.g., external monitor , LCD projector).
1-1 4 Hardware S pecifications and Configurations Right V iew 0 Figure 1-4. Right View T able 1-4. Right View No Icon Item Description 1 USB 2.0 ports Connect to USB 2. 0 devices (e .g., USB mouse, USB camera). 2 Optical drive Internal optical drive; accept s CDs or DVDs.
Hardware S p ecifications and Configurations 1-15 Base Vi ew 0 Figure 1-5. Base View T able 1-5. Base View No Icon Item Description 1 Battery bay Houses th e comp ut er's battery pack. 2 Battery release latch/ lock Releases the battery for removal.
1-1 6 Hardware S pecifications and Configurations Touchpad Basics 0 Figure 1-6. T ouchpad Move finger across the T ouchpad (1) to move the cursor . Press the right (2) and left (3) buttons locat ed beneath th e T ouchpad to perfor m sele ction and execution functions.
Hardware S p ecifications and Configurations 1-17 Using the Keyboard 0 Figure 1-7. Keyboard Lock Keys The keyboard has three lock keys which can be toggled on and off. (T able 1-7) The embedded numeric keyp ad functions like a desktop numeric keyp ad.
1-1 8 Hardware S pecifications and Configurations Windows Keys 0 The keyboard has two keys that perform Windows-sp ecific functions. Windows Logo key Application key T able 1-9.
Hardware S p ecifications and Configurations 1-19 HotKeys 0 Hotkeys or key comb inations can be used to access mo st of the comput er 's contr ols like screen brightness and volume outp ut. Figure 1-8. Keyboard HotKeys T o activate hotkeys, press and hold the <Fn> ke y before pressing the other key in the ho tkey combination.
1-2 0 Hardware S pecifications and Configurations <Fn> + < > Brightness up Increases the screen br ightness. <Fn> + < > Brightness do wn Decreases the scree n brig htne ss. <Fn> + < > V olume up Increases audio volume .
Hardware S p ecifications and Configurations 1-21 System Block Diagram 0 Figure 1-9. System Block Diagram USB port 8 6.4G/8.5 G/10.6G 100M/133M /166M(CFD) 100MHz 33MHz 100MHz 100MHz 1GB/s x4 DMI x4 FDI x8 port 2,4 port 1 LVDS Conn. CRT Conn. SPI 3.3V 24MHz 10/100M LAN BCM57780 MINI Card x1 WLAN CMOS Camera Dual Channel 2.
1-2 2 Hardware S pecifications and Configurations Specification Tables 0 Computer specif ications Item Metric Imperial Dimensions Length 25.30 cm 9.96 in Width 38.16 cm 15.02 in Height (front to rear) 2.74 to 3.4 0 cm 1.08 to 1.34 in Weight (equi pped with optical drive, flash drive, and battery) 2.
Hardware S p ecifications and Configurations 1-23 System Board Major Ch ips Processor Item Specification Core lo gic Intel ® HM55 VGA Intel ® Arrandale (MCP Processor) LAN Broadcom BCM57780 A1KMLG for 10 /100M LAN Contr oller USB 2.
1-2 4 Hardware S pecifications and Configurations Processor S pecifications CPU Fan T rue V alue T able (Tj=105) Item CPU Speed (GHz) Cores/ Threads Bus Speed (FSB/ DMI/QBI) Mfg Te c h (nm) Cache Size (MB) Package Vo l t a g e P6100 2 2 FSB:NA QPI:NA DMI: 2.
Hardware S p ecifications and Configurations 1-25 CPU Fan T rue V alue T able (Tj=90) System Memory CPU T emp Fan Speed (RPM) S PL Spec (dBA) 57 2500 28 64 2900 31 70 3200 34 78 3600 37 85 4000 40 .
1-2 6 Hardware S pecifications and Configurations Memory Combinations Vid eo In te r fa ce Slot 1 (MB) Slot 2 (MB) T otal Memory (MB) 0 512 512 0 1024 1024 0 2048 2048 0 4096 4096 512 0 512 512 512 10.
Hardware S p ecifications and Configurations 1-27 BIOS LAN Interface Item Specif ication BIOS vendor Insyde BIOS V ersion 1.00 BIOS ROM type MX25L3205D, MX25L3206E, W25Q32BV , EN25F32 BIOS ROM size 4M.
1-2 8 Hardware S pecifications and Configurations Keyboard Hard Disk Drive (A VL components) Item Spec ification T ype New A cer TM7T flat keyboard T otal number of keyp ads 105-US/106-UK keys Windows.
Hardware S p ecifications and Configurations 1-29 Super-Multi Drive Item Specif ication V endor & Model name HLDS Super-Multi Drive DL 8X G T32N LF/SONY Super-Mu lti Drive DL 8X AD-758 5H LF/Panas.
1-3 0 Hardware S pecifications and Configurations BD Drive Items Specifications V endor & Model name PLDS BD COMBO DRIVE TRA Y DL DS -4E1S LF/HLDS BD COMBO 12.7mm T ray DL CT21N/SONY BD COMBO DRIVE TRA Y DL BC-5500H-AR Performance S pecific ation With CD Disc With DVD Disc With Blu-ray Disc T ransfer rate (Mbytes/sec) Sustained: Max 3.
Hardware S p ecifications and Configurations 1-31 LED 15.6” Item Specificatio n V endor/Model name AUO/B156XW02 V3 Samsung/L TN156A T02-101 LG/LP156WH2-TLF1 LG/LP156WH2-TLF A AUO.
1-3 2 Hardware S pecifications and Configurations LCD Inverter (no t av ai la bl e in thi s mode l) Display Supported Resolution (LCD) Graphics Controller Display Supported Resolution (GPU) Item Speci.
Hardware S p ecifications and Configurations 1-33 Bluetooth Interface ( not available in this model) Bluetooth Module (not available in this model) Camera Mini Card 3G Card (not available in this mode.
1-3 4 Hardware S pecifications and Configurations Audio Codec and Amplifier Audio Interface Item Specificat ion Audio Cont roller Audio code c: Realtek ALC272 X-GR Features T wo stereo DAC support.
Hardware S p ecifications and Configurations 1-35 Wireless Module 802.1 1b/g/n Battery Audio In te rfa ce (con ti nued) Internal micropho ne Y es Internal spea ker/quantit y Y es/(1W speakers x2) Item.
1-3 6 Hardware S pecifications and Configurations VRAM (not available in this model) USB Port HDMI Port (not availa ble in this model ) AC Adapter Item Specification Chip set N/A Memory size N/A Interface N /A Item Specificatio n USB compliance level USB 2.
Hardware S p ecifications and Configurations 1-37 System Power Managemen t Card Reader Item Specification Mech. Off (G3) All devices in the system ar e tu rn ed off completely . Soft Of f (G2/S5) OS initiated shutdown. All devices in the system are tu rned off completely .
1-3 8 Hardware S pecifications and Configurations System LED Indicator System DMA Specification Item Specification Lock N/A System state Blue color solid on: System on Blue color of f: System off HDD .
Hardware S p ecifications and Configurations 1-39 System Interrup t Specific at ion Hardware IRQ System Function IRQ0 System timer IRQ1 S tandar d 101-/102-K ey or Micr osoft ® Natural Keyboard IRQ2 .
1-4 0 Hardware S pecifications and Configurations System IO Address Ma p I/O address (hex) Sy stem function (shipping co nfi guration) 000 - 00F DMA controller no.
Hardware S p ecifications and Configurations 1-41 System I/O Address S pecifications I/O addres s (h e x) System Function (shipping c onfiguration) 220 - 22F Entertainme nt aud io 230 - 26D Unused 26E.
1-4 2 Hardware S pecifications and Configurations.
CHAPTER 2 System Utilities.
2-2 BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Navigating the BIOS Ut ility . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Utilities 2-3 System Utilities BIOS Setup Utility 0 This utility is a hardware configuration program built into a computer’s BIOS (Basic Input/Output System). The utility is pre-configur ed and optimized so most users do not need to run it. If configuration problems occur , the setup utility may need to be run.
2-4 System Utilities BIOS 0 The following is a description of the tabs found on the InsydeH2 0 BIOS Setup Utility screen: NOTE: NOTE : Screens provided are for re ference only . Actual values may dif fer by model. Information 0 The Information t ab shows a summar y of computer har dware information.
System Utilities 2-5 System BIOS V ersion System BIOS version VGA BIOS V ersion VGA (video graphic s array) firmware vers ion of system Serial Number Ser ial number of unit Asset T ag Number As set tag number of system Product Name Product name of the system UUID Universally Unique Identifier T able 2-1.
2-6 System Utilities Main 0 The Main t ab allows the user to set system time and da te, enable or disable boot optio n and enable or di sable recovery .
System Utilities 2-7 D2D Recovery Option to use D2D Recovery func tion O ption: Enable d or Disabled SA T A Mode Option to set SA T A contro ller mode Option: A HCI or IDE T able 2-2.
2-8 System Utilities Security 0 The Security t ab shows par ameters that safeguard and pr otect the computer from unauthorize d use. Figure 2-3. BIOS Security T able 2 -3 describes t he parameters shown in Figure 2- 3.
System Utilities 2-9 NOTE: NOTE : When prompted to enter p assword, three atte mpts ar e allowed before system halt s. Resetting BIOS password may r equire computer be returned to dealer . Setting a Password 0 Perform the following to set a new user or sup ervisor passwords: 1.
2-10 System Utilities Figure 2-5. Setting a Pa ssword Confirmation Noti ce a. Press Enter to return to the BIOS Setup Utility Security menu. b. The Supervisor Password parame ter is shown as Set. c. Press F10 to save changes an d ex it BIOS Setup Utility .
System Utilities 2-1 1 3. Press Enter twic e without ty ping anything in Enter New Password and Confirm New Password fields. Computer will set Supervisor Password p arameter to Clear . 4. Press F10 to save changes and exit the BIOS Setup U tility . Changing a Password 0 1.
2-12 System Utilities a. Press Enter to ret urn to the BIOS Setup Utility Security menu. b. The Supervisor Password parame ter is shown as Clear. c. T o try to change the password again , repeat steps 1 through 4 . If new password and conf irm new password strings do not m atch, the Setup Warning dialog is shown (Figure 2-1 1).
System Utilities 2-13 Boot 0 This tab allows chang es to the order of boot devices used to load the operating system. Bootable devices includ e the: USB diskette drives Onboard hard disk drive DVD drive in the module bay Use and keys to select a device and press F5 or F6 to change the va lue.
2-14 System Utilities Exit 0 The Exit tab allows users to save or discard changes and quit the BIOS Setup Utility . Figure 2-13. BIOS Exit T able 2-5 describes the pa rameters in Figure 2-13. T able 2-5. Exit Parameters Parameter Description Exit Saving Changes Exit BIOS utility and save setup item changes to system.
System Utilities 2-15 BIOS Flash Utilities 0 BIOS Flash memory u pdates are required for the following conditions: New versions of system programs New features or options Restore a BIOS when it becomes corrupted. Use the Flash utility to update the system BIOS Flash ROM.
2-16 System Utilities Remove HDD/BIOS Password Utilities 0 CAUTION : ! If Power-on Password authentication is enabl ed, the BIO S password can only be cleared by initiating the Crisis Disk Recovery procedure. See BIOS Recovery by Crisis Disk . Clearing HDD Passwords 0 This section provides details ab out re moving an HDD password from the BIOS.
System Utilities 2-17 4. Execute UnlockHD.exe ( Figure 2- 16 ) to create a password un lock code. Use the format < UnlockHD [key code] > with the code noted in the Figure 2-17 . Example: UnlockHD 54591747 The command genera te s a password which can be used for unlocking the HDD.
2-18 System Utilities Removing BIOS Passwords 0 T o clear User or Supervisor p asswords, open the DIMM door and use a me tal instrum ent to short the RTCRST# point. Figure 2-18. CMOS Jumper Overview Software Method 0 1. At a DOS promp t, en te r cl npwd.
System Utilities 2-19 Miscellaneous Tools 0 Using Boot Sequence Selector 0 The Boot Sequence Selector allows the boot or der to be ch anged without a ccessing the BIOS Setup Utility . T o use the Boot Sequence Selector , pe rf or m th e fo llowin g : 1.
2-20 System Utilities Using Boot Manager 0 The Boot Manager allows the boot order to be changed witho ut accessing the BIOS Setup Utility . T o use the Boot Manager , perform the following: NOTE: NOTE : The F12 Boot Me nu option mu st be set to Enabled in the BIOS Setup Utility ’s Main screen.
System Utilities 2-21 The following examp les show the commands and the corresponding outp ut information: Read DMI Informat ion from Memory Input: 0 dmitools /r Output: 0 Manufacturer (T ype1, Offset.
2-22 System Utilities Using LAN EEPROM Utility 0 Use EEPROM.BA T to write data to LAN EEPROM under DOS mode. 1. In DOS mode, navigate to 57780_HMA51CP folder (Figure 2-23). Figure 2-22. Updating EEPROM 2. Run EEPROM.BA T to automatically modify da ta in LAN EEPROM.
CHAPTER 3 Machine Maintenance Procedures.
3-2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Recommended Equipment . . . . . . . . . . . . . . . . . .
3-3 Camera Module Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-42 Camera Module Installa tion . . . . . . . . . . . . . . . . . . . . . . . . . 3-42 LCD Panel Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4.
Machine Maintenance Procedure s 3-5 Machine Maintenance Procedures Introduction 0 This chapter cont ains general in formation about the notebook, a list o f tools needed to perform the required ma intenance and ste p by step procedures on how to remove and inst all components from the notebook computer .
3-6 Machine Maintenance Proced ures Screw Table 0 T able 3-1 cont ains a comple te list of the req uired screws and fasten ers required when performing any maintena nce on the notebook computer . T able 3-1. Main Screw List Screw Qua ntity Acer Part Number M2.
Machine Maintenance Procedure s 3-7 Maintenance Flowchart 0 The flowchart in Figure 3-1 pr ovides a graphic represent ation of the module remova l and installation sequences. It provides information on wh at components ne ed to be removed and installed during servicing.
3-8 Machine Maintenance Proced ures Getting Started 0 The flowchart in Fig ure 3-1 identifies sections illustrating the entire removal and install sequence. Observe the order of the sequence to avoid damag e to any of the hardware components. Perform the f ollowing prior to performing any maintena nce procedur es: 1.
Machine Maintenance Procedure s 3-9 Battery Pack Removal 0 1. Place computer battery side up. 2. Slide battery lock (A) into open position. 3. Slide and hold battery r elease latch (B ) to release position. Using tab (C) open and remove ba ttery pack (D) from lower cover .
3-1 0 Machine Maintenance Proced ures Dummy Card Removal 0 1. Push in dummy card (A) to release. 2. Remove dummy card (A ). Figure 3-5. Dummy Card Dummy Card Installation 0 1.
Machine Maintenance Procedure s 3-1 1 Lower Logic Door Removal 0 Prerequisite: Battery Pack Removal 1. Remove t wo (2) screw s (C). 2. Using tab (B), remove door (A) from lower cover . Figure 3-6. Lower Logic Door Lower Logic Door Installation 0 1. Insert door fla nges into five (5) slots (D) on lower cover (Figure 3-7).
3-1 2 Machine Maintenance Proced ures HDD Module Removal 0 Prerequisite: Lower Logic Door Removal 1. Remove s crews (D) fro m module (A). Figure 3-8. HDD Module 2. Use mylar tab (C) to lif t and remove module (A) from ma inboard connector dock (F). Figure 3-9.
Machine Maintenance Procedure s 3-13 4. Remove m odule (A) fro m mylar (C) and brackets. Figure 3-10. HDD Bracket s HDD Module Installation 0 1. Install module (A) into brackets (F ) and mylar (C) (Figure 3-10). 2. Install and secure module to br ackets with four (4) screws (E) (F igure 3-10).
3-1 4 Machine Maintenance Proced ures DIMM Module Removal 0 Prerequisite: Lower Logic Door Removal 1. Lift mylar (D) to provide acce ss to module ( A). 2. Push module (A) clips (B) to unlock module. Figure 3-1 1. DIMM Module 3. Slide module (A) from mainb oard connector (C).
Machine Maintenance Procedure s 3-15 WLAN Module Removal 0 Prerequisite: Lower Logic Door Removal 1. Locate m odule (A) on lower cover . 2. Lift mylar (F) t o provide a ccess to modu le (A). 3. Disconnect antenn a ca ble (B) from WLAN module. 4. Remove s crew (D) from module.
3-1 6 Machine Maintenance Proced ures R TC Battery Removal 0 Prerequisite: Lower Logic Door Removal 1. Through opening (B) in mainboard connector , push battery (A) to release. 2. Lift battery to rem ov e. Figure 3-13. RTC Battery NOTE: NOTE : Follow local regulations for ba tte ry disposal.
Machine Maintenance Procedure s 3-17 Optical Disk Drive (ODD) Module Removal 0 Prerequisite: Lower Logic Door Removal 1. Remove s crew (B) from lower cover . 2. Remove m odule from b ay . Figure 3-14. ODD Module 3. Remove two (2) screw s (D) from b racket.
3-1 8 Machine Maintenance Proced ures 5. Insert narrow tool into hole (G) on bezel, to eject module from tray (Figur e 3-17). Figure 3-16. ODD Module 6. Press down on latch (H) to unlock bezel (F) from module (A) (Figur e 3-17). 7. Remove bez el (F ) fr om modu le.
Machine Maintenance Procedure s 3-19 ID Size Quantity Screw T ype B M2.45x8 1 DM 2 x 3 2.
3-2 0 Machine Maintenance Proced ures Keyboard Removal 0 1. Locate (6) keyboard locks (B). Figure 3-18. Keyboard Locks 2. Unlock keyboard locks (Figure 3-19). Figure 3-19. Keyboard Locks CAUTION : ! Use caution when removing keyb oa rd. Keyboard is att ached to mainboard by Flexible Printed Circuits (FPC) cable.
Machine Maintenance Procedure s 3-21 3. Place keyboard facedown onto p almrest. 4. Disconnect FPC cable (A) from mainb oar d connector (B). Figure 3-20. Keyboard 5. Remove ke yboard. Keyboard Installation 0 1. Place keyboard facedown onto p almrest (Figure 3-20).
3-2 2 Machine Maintenance Proced ures Upper Cover Removal 0 Prerequisite: HDD Module Removal Keyboard Removal DIMM Module Removal WLAN Module Removal Optical Disk Drive (ODD) Module Removal NOTE: NOTE : WLAN cables shown in the following ima ges may not reflect the final product.
Machine Maintenance Procedure s 3-23 4. Remove seven (7) screws (J) fro m upper cover (Figure 3-23). Figure 3-23. Upper Cover 5. S tarting at ODD module slot (K), sep arate upper and lower covers. Figure 3-24. Upper Cover 6. Work along edges until up pe r an d lower cove r ar e se parated.
3-2 4 Machine Maintenance Proced ures 7. Lift up per cover to remove (Figure 3-25). Figure 3-25. Upper Cover Upper Cover Installation 0 1. Align upper cove r to lower cover . 2. Press along edges to secure all latches. 3. Install and secure se ven (7) screws (J) to upper cover ( F igure 3-23 ).
Machine Maintenance Procedure s 3-25 Power Board Removal 0 Prerequisite: Upper Cover Removal 1. Locate power boar d (A) on upper cover . 2. Remove screw (C) securing board to upp er cover . Figure 3-26. Power Board 3. Guide FFC cable (D) through upper cover opening ( E).
3-2 6 Machine Maintenance Proced ures Power Board Installation 0 1. Put board (A) and module (B) o nto upper cover . 2. Install and secure scr ew (C) to boa rd (A).
Machine Maintenance Procedure s 3-27 S peakers Removal 0 Prerequisite: Upper Cover Removal 1. Locate left sp eaker (A) and right spea ke r (B) on upper cover . 2. Remove the following screws: two (2) screws (C) from left speake r (A) two (2) sc rews (C) from right speaker (B).
3-2 8 Machine Maintenance Proced ures USB Module Removal 0 Prerequisite: Upper Cover Removal 1. Locate m odule (A) on lower cover . 2. Disconn ect FFC cable (B) from mainb oard connecto r (D) 3. Remove s crew (C) from module (A). Figure 3-29. USB Module 4.
Machine Maintenance Procedure s 3-29 ODD Board Removal 0 Prerequisite: Upper Cover Removal 1. Locate b oard (A) on lo wer cover . 2. Disconnect FFC cable (F) from mainbo ard connector (C). 3. Remove screw (D) from board. Figure 3-30. ODD Board ODD Board Installation 0 1.
3-3 0 Machine Maintenance Proced ures Mainboard Removal 0 Prerequisite: Upper Cover Removal NOTE: NOTE : WLAN cables shown in the following ima ges may not reflect the final product.
Machine Maintenance Procedure s 3-31 3. Lift mainbo ard at slight angle. Figure 3-32. Mainboard CAUTION : ! DC-IN cable is connected to mainboard. Use cau tion when removin g mainboard. 4. Disconnect DC-IN cabl e (M) from mainboard conn ector (N) (Figure 3-33).
3-3 2 Machine Maintenance Proced ures Mainboard Installation 0 1. Align mainboard to lower cover . 2. Connect DC-IN cable (M) to mainbo ard connector (N) ( Figure 3- 33 ). CAUTION : ! Use caution when installing mainboard. Forced installation may damage lef t side connectors.
Machine Maintenance Procedure s 3-33 F AN Module Removal 0 Prerequisite: Mainboard Remova l 1. Locate module (A). 2. Disconnect cable (B) from mainboa rd connector (C). 3. Lift module , releasing adhesive strip ( D). Figure 3-35. F AN Module FAN Module Installation 0 1.
3-3 4 Machine Maintenance Proced ures Thermal Module Removal 0 Prerequisite: Mainboard Remova l CAUTION : ! Thermal module may be hot. 1. Remove four (4) scr ews (B) from m odule (A).
Machine Maintenance Procedure s 3-35 NOTE: NOTE : Force used during inst allation of thermal mo dule is suff icient to spread grea se over CPU top. 3. Align modu le (A) to ma inboard screw holes. 4. Install and secure fo ur (4) screws (B) in numer ical order from 1 to 4 to mainboard .
3-3 6 Machine Maintenance Proced ures CPU Removal 0 Prerequisite: Thermal Module Removal 1. Unlock CPU from mainbo ard socket by rotating captive screw (D) lef t 180º. 2. Lift CPU (A) from socket. Figure 3-37. CPU in Socket CPU Installation 0 1. Align CPU m arker (B) w ith socket ma rker (C) and install CPU in socket.
Machine Maintenance Procedure s 3-37 LCD (Liquid Crystal Display) Module Removal 0 Prerequisite: Mainboard Remova l NOTE: NOTE : WLAN cables shown in the following ima ges may not reflect the final product. 1. Guide WLAN antenna cable ( A) through opening (C) on lower cover .
3-3 8 Machine Maintenance Proced ures 2. Place computer on surface, face side up. 3. Remove f ollowing cable fr om guid es on lower cover (Figure 3-39): microphone cable (D ) WLAN cable (A) 4. Remove fou r (4 ) scr ew s (E) from lower cover .
Machine Maintenance Procedure s 3-39 LCD Module Installation 0 1. Align and install LCD module on lower cover ( Fig ure 3-40 ). 2. Install and secure fo ur (4) screws (E) to lower cover ( Figure 3-39 ). 3. Install following cables to guides on lower cover ( Figur e 3-39 ): WLAN cable (A) microphone cable (D ) 4.
3-4 0 Machine Maintenance Proced ures LCD Bezel Removal 0 Prerequisite: LCD (Liquid Crystal Display) Module Removal 1. Remove s crew caps (A) from LCD bezel. Figure 3-41. LCD Bezel 2. Remove screws (A) from LC D bezel. 3. S tarting form bottom edge of bezel, pull bezel up and away fr om LCD cover .
Machine Maintenance Procedure s 3-41 4. Move along side edges until bezel is sep arated from LCD cover . 5. Remove b ezel. LCD Bezel Installation 0 1. Align hinges side of bezel to LCD cover and press down until there is no gap between bezel and LCD module.
3-4 2 Machine Maintenance Proced ures Camera Module Removal 0 Prerequisite: LCD Bezel Removal 1. Locate camera module (A) on LCD cover . 2. Remove cable (B) from connector (C). 3. Remove camera module from ad hesive strip and guide pi ns (D) on LCD cover .
Machine Maintenance Procedure s 3-43 LCD Panel Removal 0 Prerequisite: LCD Bezel Removal NOTE: NOTE : WLAN cables shown in the following ima ges may not reflect the final product. 1. Remove f our (4) screws (A) from LCD c over . 2. Remove LCD panel (C) from guide pins (B) on LCD cover .
3-4 4 Machine Maintenance Proced ures L VDS Cable Removal 0 Prerequisite: LCD Panel Removal 1. Remove c amera cable ( A) from LCD panel. Figure 3-45. L VDS cable 2. Peel back adhesive (B) from L VDS cable (C) (Figure 3-46). 3. Disconnect LCDS cable (C) from p anel connector (D).
Machine Maintenance Procedure s 3-45 L VDS Cable Installation 0 1. Connect L VDS cable (C) to panel connector (D) ( Figure 3-46 ). 2. Secure connector with adhesive (B) ( Figure 3-46 ). 3. Install and secure L VDS cable (D) to LCD p anel ( Figure 3- 45 ).
3-4 6 Machine Maintenance Proced ures LCD Brackets Removal 0 Prerequisite: LCD Panel Removal 1. Remove s ix (6) screws (A) from brack ets (B). Figure 3-47.
Machine Maintenance Procedure s 3-47 LCD Brackets Inst allation 0 1. Align and install br acket (B) to LCD p anel. 2. Install and secure six (6) screws (A) to LCD panel (Figure 3-48).
3-4 8 Machine Maintenance Proced ures WLAN Antenna Cables and Microphone Set Removal 0 Prerequisite: LCD Panel Removal 1. Peel back foil t abs (A) as required.
CHAPTER 4 Troubleshooting.
4-2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Power On Issues . . . . . . . . . . . . . . . . . . . . .
T roubleshooting 4-3 Troubleshooting Introduction 0 This chapter contains inform at ion about trouble sho o tin g com m o n pr ob lem s as sociated with the noteboo k. General Information 0 The following procedu re s are a guide for trou bl eshooting computer pr oblems.
4-4 T roubleshooting Power On Issues 0 If the system fails to pow er on, perform the following: Figure 4-1. Power On Issue Computer Shuts Down Intermittently 0 If the system powers off at intervals, perform the following. 1. Makes sure the power cable is properly connected to the computer and the electrical outlet.
T roubleshooting 4-5 No Display Issues 0 If the Display fails, pe rform the following : Figure 4-2. No Display Issue No POST or V ideo 0 If the POST or video does not appear , perform the following, one at a time. 1. Make sur e that intern al display is selec ted.
4-6 T roubleshooting 7. Disconnect power and all exter nal devices incl uding port replicators o r docking stations. Remove any m emory ca rds and CD/DVD discs. 8. S tart the computer . If the computer boot s co rrectly , add the devices one by one until the failure point is discovered.
T roubleshooting 4-7 LCD Failure 0 If the LCD fails, perform the follow ing: Figure 4-3. LCD Failure OK NG St ar t Swap M / B Check LCD module? Swap LCD cable /LCD panel.
4-8 T roubleshooting Keyboard Failure 0 If the Keyboard fails, perform the following: Figure 4-4. Keyboard Failure No No ST AR T Keyboard FPC well connected? Keyboard OK? Connect it well Replace keybo.
T roubleshooting 4-9 T ouchp ad Failure 0 If the T ouchpad fails, perform the following: Figure 4-5. T ouchpad Failure OK NG OK NG St ar t Sw ap M/ B OK Chec k M / B T/P FFC Chec k Log i c U pper Re-a.
4-10 T roubleshooting Internal S peaker Failure 0 If internal S peakers fail, perform the following: Figure 4-6. Internal Speaker Failure Sound Problems 0 Perform the following , one at a time. 1. Boot the comp u ter. 2. Navigate to Sta r t Control Panel System and Maintenance System Device Manager .
T roubleshooting 4-1 1 Click the volume icon on the taskbar Drag the slider to 50. Confirm that the volume is not muted. Click Mixer to verify that other audio applications a re set to 50 and not mut ed. 6. Navigate to Sta r t Control Panel Hardware and Sound Sound .
4-12 T roubleshooting Microphone Failure 0 If internal or external Microp hones fail, perform the followin g: Figure 4-7. Microphone Failure 1. Check that the microphone is enabled. Navigate to Sta rt Control Panel Hardware and Sound Sound and select the Recording tab.
T roubleshooting 4-13 ODD Failure 0 Figure 4-8. ODD Failure ODD Not Operating Correctly 0 If the ODD exhibits any of the following symptoms it may be faulty: Audio CDs do not play when loaded .
4-14 T roubleshooting Access failure screen is shown The ODD is noisy Perform the following , one at a time: 1. Boot th e computer a nd retry the operation. 2. Use an differ ent disc. 3. Navigate to Sta r t Computer . Check that the ODD device is shown in the Devices with Removable Storage panel.
T roubleshooting 4-15 Discs Do Not Burn Properly 0 If discs can not be burned, perform the following: 6. Confirm that the default drive is record enab led: Navigate to St a rt Computer and right-click the writable ODD icon. Click Properties .
4-16 T roubleshooting Drive Read Failure 0 If discs cann ot be read whe n inserted in t he drive, perf orm the follow ing. 1. Remove and clean the failed disc.
T roubleshooting 4-17 USB Failure 0 If the USB fails, perform the following: Figure 4-9. USB Failure OK NG OK NG St ar t Sw ap M/ B OK Chec k IO/ B to M/B CO NN Chec k USB/B Re-ass embl e the IO/B CO .
4-18 T roubleshooting Wireless Function Failure 0 If the WLAN fails, perform the following: Figure 4-10. Wireless Function Failure OK NG St art Swap M / B OK NG OK OK NG OK OK NG OK Check antenna to W.
T roubleshooting 4-19 2 in 1 Card Fucntion Failure 0 If the 2 in 1 card function fails, perform the following: Figure 4-1 1. 2 in 1 Card Function Failure No No ST AR T Replace M/B Ch eck th e car d re.
4-20 T roubleshooting Thermal Unit Failure 0 If the Thermal Unit fails , perform the following: Figure 4-12. Thermal Failure No ST ART No No Replace M/B F a n pow e r ca b le w e ll c o nnec t ed ? F .
T roubleshooting 4-21 Other Functions Failure 0 HDD Not Operating Correctly 0 If the HDD fails to operate correctly , perform the following, one at a time. 1. Disconnect all external devices. 2. Run a complete virus scan using up-to-date soft ware to confirm th e computer is virus free.
4-22 T roubleshooting Cosmetic Failure 0 If the Cosmetic fails, perform the following: Figure 4-13. Cosmetic Failure Random Loss of BIOS Settings 0 If the computer is expe rie n cin g interm it tent lo ss of BIOS inf ormation, perform the following: 1.
T roubleshooting 4-23 2. Run a complete virus scan using up to date software to confirm the computer is virus fre e. 3. If the computer is ex periencing HDD or ODD BIOS inf ormation loss, disconnect an d reconnect the power and data cables between devices.
4-24 T roubleshooting Intermittent Problems 0 Intermittent system hang problems can be caused by a variety of re asons that have nothing to do with a hardware de f ect, such as: cosmic radiation, el ectrost atic discharge, or so ftware errors. FRU replacement sho uld be considered only when a recurring problem exist s.
T roubleshooting 4-25 Post Codes 0 The following a re the InsydeH2 O™ Functiona lity POST code tables. The componen ts of the POST code table includ es: SEC phase, PEI phase, DXE phase, BD S phase, CSM functions, S3 functions and ACPI functions. POST Code Range 0 T able 4-2.
4-26 T roubleshooting SEC_SETUP_CAR_OK SEC 07 Cache as RAM test SEC_FORCE_MAX_RA TIO* SEC 08 T une CPU frequency ratio to maximum level SEC_GO_TO_SECST ARTUP SEC 09 Setup BIOS ROM cache SEC_GO_TO_PEICORE SEC 0A En ter Boot Firm ware V o lume * 3 rd p arty relate functions – Platfor m de pendence.
T roubleshooting 4-27 PEI_ENTER_RECOVERY_MODE PEI 84 Recovery device Initialization PEI_RECOVERY_MEDIA_FOUND PEI 85 Found Recovery image PEI_RECOVERY_MEDIA_NOT_FOUND PEI 86 Recovery image not foun d P.
4-28 T roubleshooting DXE_MP_CPU_INIT DXE 4F Mul ti-processor Middle Initialization DXE_SMBUS_INIT DXE 50 SM BUS Driver Initialization DXE_SMART_TIMER_INIT D XE 51 8259 Initialization DXE_PCRTC_INIT D.
T roubleshooting 4-29 BDS_PCI_ENUMERA TION_END BDS 15 PCI enumeration complete BDS_CONNECT_CONSOLE_IN BD S 16 Keyboard Controlle r , keyboard and mouse initialization BDS_CONNECT_CONSOLE_OUT BDS 17 Vi.
4-30 T roubleshooting BDS_EFI64_SHADOW_ALL_LEGACY_R OM BDS 2C Shadow Misc Option ROM BDS_ACPI_S3SA VE BDS 2D Save S3 resume required data in RAM BDS_READY_TO_BOOT_EVENT BDS 2E Last Chipset initial bef.
T roubleshooting 4-31 T able 4-8. S3 Functions POST Code T able Functionality Name (Inclu dePostCode.h) Phase Post Code Descripti on S3_RESTORE_MEMOR Y_CONTROLLER PEI C0 Memory initial for S3 resume S.
4-32 T roubleshooting T able 4-10. SMM Functions POST Code T able Functionality Name (IncludePostCode.h) Phase Post Code Description SMM_IDENTIFY_FLASH_DEVICE SMM 0xA0 Identify Flash device in SMM SMM.
CHAPTER 5 Jumper and Connector Locations.
5-2 Jumper and Connector Locati ons . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Clearing Password Check and BIOS Recovery . . . . . . . . . . . .
5-3 Jumper and Connector Locations 0 Mainboard 0 Figure 5-1. Mainboard T op T able 5-1. Mainboard T op Item Descript ion Item Description JL VDS1 L VDS Connector JMIC2 MIC Connector JKB1 Keyboard Co n.
5-4 Figure 5-2. Mainboard Bottom T able 5-2. Mainboard Bottom Item Descript ion Item Description PJP1 DC-IN Connector J F AN 1 F AN Connector JCPU1 C PU Socket JMIC1 Audio Jack (MIC) JUSB1 USB Connector JHP1 Audio Jack (Earphone) JCRT1 D-SUB Connector JRJ45 RJ45 PJP2 Battery Connector JHDD 1 SA T A H DD Connector JDIMM2 D DR3 Socket H4.
5-5 Clearing Password Check and BIOS Recovery 0 This section prov ides us er s wi th th e standard op e ra tin g pr oc ed ur es of clearing password and BIOS recovery for the As pir e AS5333/AS5733/AS5733Z. The machine prov ides one Hardware Open Gap on main b oard for clearing pa ssword check, and one Hotkey for ena bling BIOS Recovery .
5-6 Figure 5-4. CMOS Jumper 4. Plug in AC adapter . 5. Press Power button until BIOS POST is finished. 6. Remove conductivity to ol from RCT_RST point. 7. Restart the system and press F2 to enter BIOS Utility Setup menu. 8. If no password prompt is sh own, BIOS password is cleared.
5-7 BIOS Recovery by Crisis Disk 0 BIOS Recovery Boot Bloc k 0 BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS initialization. Users can enable th is feature to restore the BIOS firmware if a previous BIOS flashing process has failed.
5-8 2. Copy ROM (read-only memory) file, Q5WP2X64.fd , to root directory of USB HDD. Make sure that there is no other BIOS f ile is saved in th e same director y . 3. Insert USB HDD into USB port. 4. Press Fn + ESC button and hold while pluggin g in AC po wer adapter .
CHAPTER 6 FRU (Field Replaceable Unit) List.
6-2 Exploded Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Main Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Upper Cover Assembly . . . . . . . . . . . . . . . . . . . . . . .
FRU (Field Repla ceable Unit) List 6-3 FRU (Field Replaceable Unit) List This chapter provides users with a FRU (Fie ld Replaceable Unit) listing in global configurations for the Aspire AS5333/AS5733/AS5733Z. Refer to this chapter wh ene ver ordering for p arts to rep air or for RMA (Return Merchandise Autho rizatio n).
6-4 FRU (Fie ld Replaceable Unit) List Exploded Diagrams 0 Main Assembly 0 Figure 6-1. Main Assembly Exploded Diagra m T able 6-1. Main Assembly Exploded Diagram No. Description P/N No. Desc ription P/N 1 Upper Cover 60.RJW02.001 2 F AN Module 23.R4F02.
FRU (Field Repla ceable Unit) List 6-5 Upper Cover Assembly 0 Figure 6-2. Upper Cover Assembly T able 6-2. Upper Cover Assembly No. Description P/N No. Desc ription P/N 1 T ouchpad 2 T ouchpad FFC 50.R4F02.003 3 Right S peaker 23.RJW02.001 4 Left S p eaker 23.
6-6 FRU (Fie ld Replaceable Unit) List LCD Assembly 0 Figure 6-3. LCD Assembly Exploded Diagram T able 6-3. LCD Assembly No. Descripti on P/N No. Description P/N 1 LCD Bezel 60.RJW02.004 2 LCD Panel LK.15605.019 3 L VDS Cable 50.R4F02.009 4 Left Bracket 33.
FRU (Field Repla ceable Unit) List 6-7 FRU List 0 T able 6-4. FRU List Category Description P/N ADAPTER Adapter DEL T A 65W 19V 1.7x5.5x1 1 Y ellow ADP-65JH DB A, L V5 LED LF AP .06501.02 6 Adapter LITE-ON 65W 19V 1.7x5.5x1 1 Y ellow P A-1 650-22AC L V5 LED L F AP .
6-8 FRU (Fie ld Replaceable Unit) List FOXCONN WIRELESS LAN BROADCOMM 43225 2X2 BGN (HM) T77H103.00 NI.23600.066 FOXCONN WIRELSS LAN A THEROS H B95 1X1 BGN (HM) T7 7H121.01 NI.23600.068 LITEON WIRELESS LAN A THEROS HB95 1X1 BGN (HM) WN6601AH NI.23600.
FRU (Field Repla ceable Unit) List 6-9 CASE/COVER/BRACKET ASSEMBL Y UPPER CASE ASSY INCL TP & NAMEPLA TE - ASPIRE 60.RJW02.001 LOWER CASE-UMA FOR AS5333, AS5733,AS5733Z 60.RJW02.002 UNILOAD DOOR-UMA 42.R4F02.001 HDD CARRIER-UMA 33.R4F02.001 CPU/PROCESSOR CPU Intel Pentium Dual-Core P6100 PGA 2.
6-1 0 FRU (Field Replaceable Unit) List ODD P ANASONIC Super-Multi DR IVE 12.7mm T ray DL 8X UJ8A0 LF W/O bezel SA T A (HF + Windows 7) Foxconn Y en tai Facotr y KU.00807.075 ODD P ANASONIC Super-Multi DR IVE 12.7mm T ray DL 8X UJ8B0 LF W/O bezel SA T A (HF + ZP) Foxconn Y entai Facotry KU.
FRU (Field Repla ceable Unit) List 6-1 1 HDD SEAGA TE 2.5" 5400rpm 320GB ST320L T020 /9YG142-188, Sapt a 15,320G/P SA T A 8MB LF+HF F/W: 0001SDM1 KH.32001.021 HDD HGST 2.5" 5400rpm 500GB HTS545050B9A300 Pa nther B SA T A LF F/W:C60F Disk imbalance criteria = 0.
6-1 2 FRU (Field Replaceable Unit) List Keyboard ACER AC7T_A10B AC7T Internal 17 S tandard 103KS Black Arabic T exture KB.I170A.147 Keyboard ACER AC7T_A10B AC7T Internal 17 S tandard 103KS Black Chinese T exture KB.I170A.151 Keyboard ACER AC7T_A10B AC7T Internal 17 S tandard 10 3KS Black Russian T exture KB.
FRU (Field Repla ceable Unit) List 6-13 Keyboard ACER AC7T_A10B AC7T Internal 17 S tandard 104KS Black FR/Arabic T exture KB.I170A.153 Keyboard ACER AC7T_A10B AC7T Internal 17 S tandard 10 4KS Black Nordic T exture KB.I170A.161 Keyboard ACER AC7T_A10B AC7T Internal 17 S tandard 104KS Black SLO/CRO T exture KB.
6-1 4 FRU (Field Replaceable Unit) List LED CABLE FOR W /CMOS 50.R4F 02.009 LED BRACKET R&L 33.R4F02.004 CAMERA 0.3M - AS5333,AS5733,AS5733Z 57.RJW02.001 LED LCD AUO 15.6"W WXGA Glare B156XW02 V6 LF 200nit 8ms 400:1 LK.15605 .019 LED LCD CMO 15 .
FRU (Field Repla ceable Unit) List 6-15 MAINBOARD Mainboard AS573 3Z Int el HM 55 LF HMA5 1_CP (NO HDMI) MB.RJW02.001 MEMOR Y Memory UNIFOSA SO-DIMM DDRIII 1333 1GB GU672203EP0200 LF 128* 8 0.065um KN.1GB0H.017 Memory KINGSTON SO-D IMM DDRIII 1333 1GB ACR128X64D3S1333C9 LF 128* 8 0.
6-1 6 FRU (Field Replaceable Unit) List SPEAKER L 23.R4F02.003 SPEAKER R - AS5733Z 23.RJW02.001 MISCELLANEOUS LCD SCREW P AD 47.R4F02.00 1 T able 6-4. FRU List (Continued) Category Description P/N.
FRU (Field Repla ceable Unit) List 6-17 Screw List 0 T able 6-5. Screw List Category Descripti on P/N SCREW SCREW 2.5D 5 L K 5.5D ZK NL + CR3 8 6.R4F02.001 SCREW 2.45D 8.0L K 5.5D 0. 8T ZK NL 86.R4F02. 002 SCREW 2.5D 6L K 5.5D NI NL 86.R4F02.0 03 SCREW 1.
6-1 8 FRU (Field Replaceable Unit) List.
CHAPTER 7 Model Definition and Configuration.
7-2 Aspire AS5333 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Aspire AS5733 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 Aspire AS5733Z . . . . . . . . . . . . . . . . . . . . .
Model Definition a nd Configuration 7-3 Model Definition and Configuration Aspire AS5333 0 T able 7-1. RO & Description Model Country P/N RO Description AS5333-P462G32Mikk WW S2.RNC02.001 WW AS5333-P462G32Mikk W7HP64ASWW1 MC UMACkk_3 1*2G/320/6L2.
7-4 Model Definition and Con figu ration Aspire AS5733 0 T able 7-5. NB Chips et, Battery & Adapte r Model Country P/N NB Chip set Battery Adapter AS5333-P462G32Mikk WW S2.RNC02.001 HM55 6CELL2.2 65W AS5333-P463G32Mikk CA LX.RNC02.001 HM55 6CELL2.
Model Definition a nd Configuration 7-5 AS5733-374G32Mikk UK LX.RN502.016 EMEA AS5733-374G32Mikk W7HP64ASGB1 MC UMACkk_3 1*4G/320/6L2.2/2R/CB_GN_0.3 C_AN_EN1 1SP1 AS5733-374G50Mikk AU/NZ LX.RN502.009 AAP AS5733-374G50Mikk W7HP64ASAU1 MC UMACkk_3 1*4G/500/6L2.
7-6 Model Definition and Con figu ration AS5733-384G32Mikk DE LX.RN502.001 EMEA AS5733-384G32Mikk W7HP64ASDE1 MC UMACkk_3 1*4G/320/6L2.2/2R/CB_GN_0.3 C_AN_DE1 1 AS5733-384G50Mikk AU/NZ LX.RN502.006 AAP AS5733-384G50Mikk W7HP64ASAU1 MC UMACkk_3 1*4G/500/6L2.
Model Definition a nd Configuration 7-7 AS5733-384G32 Mikk DE LX.RN502.001 Ci3380M UMA SO4GBIII10 AS5733-384G50 Mikk AU/NZ LX.RN502.006 Ci3380M UMA SO4GBIII10 AS5733-384G64 Mikk AU/NZ LX.RN502.012 Ci3380M UMA SO4GBIII10 AS5733-38 4G64Mikk RO LX.RN50C.
7-8 Model Definition and Con figu ration T able 7-9. ODD & Wireless LAN1 Model Country P/N ODD Wireless LAN1 AS5733-372G32Mikk AU/NZ LX.RN502.007 NSM8XS 3rd WiFi 1x1 BGN AS5733-372G32 Mikk MOYO LX.RN501. 001 NSM8XS 3rd WiFi 1x1 BGN AS5733-372G32 Mikk WW S2.
Model Definition a nd Configuration 7-9 Aspire AS5733Z 0 AS5733-374G32 Mikk UK LX.RN 502.016 HM55 6CELL2.2 65W AS5733-374G50Mikk A U/NZ LX.RN502.009 HM55 6CELL2.2 65W AS5733-374G50 Mikk DE LX.RN 502.017 HM55 6CELL2.2 65W AS5733-374G50 Mikk UK LX.RN 502.
7-1 0 Model Definition and Con figu ration AS5733Z-P614 G50Mikk BE LX.RJW 02.016 EMEA AS5733Z-P614G50Mikk W7HP64ASBE1 MC UMACkk_3 1*4G/500_L/6L2.2/2R/CB_G N_0.3C_AN_NL1 1SP1 AS5733Z-P614 G50Mikk CA LX.RJW 02.010 P A AS5733Z-P614G50Mikk W7HP64ASCA2 MC UMACkk_3 2*2G/500_L/6L2.
Model Definition a nd Configuration 7-1 1 AS5733Z-P622G32 Mikk AU/NZ LX.RJW02.012 AAP AS5733Z-P622G32 Mikk W7HP64ASAU1 MC UMACkk_3 1*2G/320/6L2.2/2R/CB_GN_ 0.3C_outer_AN _ES62 AS5733Z-P622 G32Mikk RO LX.RJW0C.002 EMEA AS5733Z-P622G32Mikk LinpusMGARO2 UMACkk_3 1*2G/320/6L2.
7-1 2 Model Definition and Con figu ration AS5733Z-P623 G50Mikk RU LX.RJW 01.001 EMEA AS5733Z-P623G50Mikk W7HB64RUASRU1 MC UMACkk_3 2G+1G/500_L/6L2.2/2R/CB_ GN_0.3C_AN_RU1 1 AS5733Z-P624G32 Mikk AU/NZ LX.RJW02.01 1 AAP AS5733Z-P624G32 Mikk W7HP64ASAU1 MC UMACkk_3 1*4G/320/6L2.
Model Definition a nd Configuration 7-13 AS5733Z-P614 G50Mikk DE LX.RJW02.008 PMDP6100 UMA SO4GBIII10 AS5733Z-P614 G50Mikk FR LX.RJW02.015 PMDP6100 UMA SO2GBIII10 AS5733Z-P614 G50Mikk IT LX.RJW02.009 PMDP6100 UMA SO4GBIII10 AS5733Z-P614 G50Mikk LU LX.
7-1 4 Model Definition and Con figu ration AS5733Z-P614 G50Mikk FR LX.RJW02.015 SO2GBIII10 N500GB5.4KS_4K AS5733Z-P614 G50Mikk IT LX.RJW02.009 N N500GB5.4KS_4K AS5733Z-P614 G50Mikk LU LX.RJW02.018 N N500GB5.4KS_4K AS5733Z-P614 G50Mikk NL LX.RJW02.017 N N500GB5.
Model Definition a nd Configuration 7-15 AS5733Z-P614 G50Mikk IT LX.RJW02. 009 NSM8XS 3rd WiFi 1x1 BGN AS5733Z-P614 G50Mikk LU LX.RJW02. 018 NSM8XS 3 rd WiFi 1x1 BGN AS5733Z-P614 G50Mikk NL LX.RJW02. 017 NSM8XS 3 rd WiFi 1x1 BGN AS5733Z-P614 G50Mikk US LX.
7-1 6 Model Definition and Con figu ration AS5733Z-P614 G50Mikk LU LX.RJW02.018 HM55 6CELL2.2 65W AS5733Z-P614 G50Mikk NL LX.RJW02.017 HM55 6CELL2.2 65W AS5733Z-P614 G50Mikk US LX.RJW02.007 HM55 6CELL2.2 65W AS5733Z-P622 G25Mikk TR LX.RJW08.002 HM55 6CELL2.
CHAPTER 8 Test Compatible Components.
8-2 Microsoft® Windows® 7 Environment Test . . . . . . . . . . . . . . . . 8-4.
T e st Compatible Compone nts 8-3 Test Compatible Components This computer ’s compatibility is tested and verified by Acer ’s internal te sting department. All of its system functions ar e tested under Windows ® 7 environment. Refer to the following list s for componen t s, adapter cards, a nd peripher als which have passe d these tests.
8-4 T est Compatib le Comp onen ts Microsoft ® Windows ® 7 Environment Test 0 T able 8-1. Aspire AS5333/AS5733/AS5733Z V endor Ty p e Description P/N Adapter 10001023 LITE-ON 65W Adapter LITE-ON 65W 19 V 1.7 x5.5x1 1 Y ellow P A-1650-22AC L V5 LED LF AP .
T e st Compatible Compone nts 8-5 10001023 LITE-ON 0.3M Liteon 0.3M L T7675AL AM.21400.078 PLM000 12 Suyin 0.3M Suyin 0.3M SY_7675_AL AM.21400.109 Card Reader 10000981 MISC 2-in-1 card reader 2-in-1 card reader CR.21500.0 30 CPU 10001067 INTEL PMDP6100 CPU Intel Pentium Du al-Core P6100 PGA 2.
8-6 T est Compatib le Comp onen ts 60001994 WD N640GB5.4KS _4K HDD WD 2.5" 5400rpm 640GB WD6400BPVT -22HXZT1, ML375M SA T A 8MB LF F/W: 01.01A01 KH.64008.005 60001994 WD N750GB5.4KS _4K HDD WD 2.5" 5400rpm 750GB WD7500BPVT -22HXZT1 , ML375M, 4K drive SA T A 8MB LF F/W:01.
T e st Compatible Compone nts 8-7 60002036 SEAGA TE N750GB5.4KS _4K HDD SEAGA TE 2.5" 5400rpm 750GB ST9750423AS,9ZW14G-188, De saru5, 375G/P . SA T A 8MB LF+HF F/W:0001 SDM1 KH.75001.01 1 Keyboard 60004864 DARFON AC7T_A10B Keyboard ACER AC7T_A10B AC7T Internal 17 S tandard Black NONE Y2010 Acer T exture KB.
8-8 T est Compatib le Comp onen ts 60004668 ELPIDA SO4GBIII10 Memory NONE SO-DIMM DD RIII 1066 4GB dummy P/N LF KN.4GB00.001 60004668 ELPIDA SO4GBIII13 Memory ELPIDA SO-DIMM DDRII I 1333 4GB EBJ41UF8BCS 0-DJ- F LF 256*8 46nm KN.4GB09.002 60024207 KINGST ON- F AR EAST SO1GBIII13 Memory KINGSTON SO-DIMM DDRIII 1333 1GB ACR128X64D3S133 3C9 LF 128*8 0.
T e st Compatible Compone nts 8-9 9999995 ONE TIME VENDER N N KI.22800.01 1 VGA Chip 10001067 INTEL UMA UMA (Intel) KI.2320 0.038 WiFi Antenna 10000105 WNC PIF A PIF A LZ.23500.006 Wireless LAN 10001018 HON HAI 3rd WiFi 1x1 BGN Foxconn Wirelss LAN Atheros HB125 1x1 BGN NI.
8-1 0 T est Compatible Comp onen ts.
CHAPTER 9 Online Support Information.
9-2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3.
Online Support Information 9-3 Online Support Information Introduction 0 This section describes online tech nical support services available to he lp users repair their Acer Systems. For distributors, dealers, ASP or TPM, please refer the technical querie s to a local Acer branch of fice.
9-4 Online Suppo rt Information.
Een belangrijk punt na aankoop van elk apparaat Acer AS5333 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Acer AS5333 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Acer AS5333 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Acer AS5333 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Acer AS5333 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Acer AS5333 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Acer AS5333 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Acer AS5333 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
