Gebruiksaanwijzing /service van het product 1691620 van de fabrikant Simplicity
Ga naar pagina of 20
A TT ACHMENT OPERA T OR’S MANUAL Snow Plow/Dozer Blade Mfg. No. Description 1691520 42” Snow Plow/Dozer Blade Hitch Mfg. No. Description 1692039 Hitch (for Landlord / 1700 / 2700 Series & Broa.
.
1 Recommended Accessories ...................................................................................................................................1 Safety Rules ...............................................................................
2 Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of vehicle, severe personal injury to yourself or bystanders, or damage to property or equipment. The tri- angle in the text signifies important cautions or warnings which must be followed.
3 Components A. Blade Assembly B. I.D. Plate C. Hex Nut, 5/16-18 (4) D. Eyebolt (2) E. Tension Spring (2) F. Pivot Frame Assembly G. Hex Lock Nut, 1/2-13 (2) H. Spacer (2) I. Hex Capscrew, 1/2-13 x 1 (2) J. Shoe Assembly (2) K. Plain Washer, 3/8 (4) L.
4 Components Broadmoor/L T/1600/2600, & Landlord/GT/1700/2700 Series Parts Figure 2. Mfg. No. 1692039 Push Bar & Lift Rod Components A. Set Collar (Qty. 2) B. Setscrew, 5/16 x 1/2 (Qty. 2) C. Rod Guide Assembly D. Spring E. Lift Rod, (Manual or Electric Lift) F.
5 Components Figure 3A. Mfg. No. 1692624 Push Bar & Lift Rod Components A. Set Collar (Qty. 2) B. Setscrew, 5/16 x 2 (Qty. 2) C. Rod Guide Assembly D. Spring E. Lift Rod F. Spring Clip (Qty. 3) G. Clevis Pin, 3/8 (Qty. 2) H. Push Bar Assembly I. Hitch Pin J.
6 Components Figure 3B. Mfg. No. 1692624 Hitch Assembly A. Hitch Assy. B. Rear Support Assy. C. Washers (Qty. 2) D. Hairpin Clip (Qty. 2) E. Pin F. Spring Clip (Qty. 4) G. Clevis Pin, 3/8 (Qty. 2) H. Rod I. Spring Assist Bracket J. Capscrew, 3/8-16 x 2 K.
7 Assembly All Models 1. Place the blade on a flat surface. 2. Regent/500/2500 & Broadmoor/LT/1600/2600 Series: See Figure 4. Install one bar stop (A) using the two 5/16-18 x 1 taptite screws (B). Do not install second bar stop. Landlord/GT/1700/2700 Series: Do not install bar stops.
NOTE: On single cylinder tractors, clevis pin (B, Figure 6) must be installed to bracket before mount- ing bracket on tractor frame. NOTE: Spring-assist bracket (A, Figure 6) does not need to be installed on units with electric lift. Broadmoor/L T/1600/2600 Series & Landlord/GT/1700/2700 Series Only: 7.
9 Regent/500/2500 Series Only: 1. Increase front tire pressure to 20 psi (138 kPa) to compensate for added weight of the hitch, plus bar and blade. Be sure both tires have equal pressure. 2. From the front of tractor, slide the hitch under the tractor so that the hitch bar is positioned at the front of the unit.
10 Installation Figure 10. A. Push Bar Hitch C. Hitch Pin B. Frame Bracket D. Safety Clip Broadmoor/L T/1600/2600 Series & Landlord/GT/1700/2700 Series 1. Drive the tractor over the push bar until rear of push bar is under front hitch. 2. Stop engine, remove key and set parking brake.
11 Installation All Models 4. See Figure 12. Raise the push bar and attach the spring (A) to the push bar bracket and the open end link of the 4-link spring assist chain. Figure 12. A. Spring Figure 13. Dozer Blade Assembled and Installed A. Push Bar D.
NOTE: Two lift rods are packaged with the Broadmoor/LT/1600/2600 & Landlord/GT/1700/2700 hitch assembly. Use the correct lift rod for manual or electric lift as shown in Figure 2. 7. Assemble lift rod per Figure 2 or 3. 8. See Figure 14. Insert prong of rod guide (A) through hole in upright of push bar (B), and secure with spring clip (C).
13 Removal 1. Lower the blade. 2. Remove blade and lift rod from push bar. 3. Raise push bar and unhook the spring from the chain. Remove the chain from the frame bracket. Reinstall safety clip to clevis pin. 4. Disconnect the lift rod from the lift lever on tractor by removing the spring clip.
Lift Rod See Figure 17. For initial setting, place front set collar (A) one inch from rod guide with blade fully lowered. Place rear set collar (B) against spring (C). Tighten the setscrews in the two set collars.To adjust, perform the following: 1. Fully raise the blade by pulling back on the tractor lift lever.
15 Adjustments Spring T ension See Figure 19. This snow plow/dozer blade is spring loaded so that when the blade strikes a solid object, the springs will allow the blade to release as shown, rather than cause damage. The blade will go back to its original position after object is cleared.
16 T orque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.
.
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 1997 Simplicity Manufacturing, Inc.
Een belangrijk punt na aankoop van elk apparaat Simplicity 1691620 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Simplicity 1691620 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Simplicity 1691620 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Simplicity 1691620 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Simplicity 1691620 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Simplicity 1691620 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Simplicity 1691620 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Simplicity 1691620 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
