Gebruiksaanwijzing /service van het product TP 100-400 van de fabrikant Snapper
Ga naar pagina of 9
:.’ OPERATOR’S MANUAL WIDE BODY CART COLLECTOR Dual Wheel Cart For Use With Turbo Collection System Form I 708219 printed in USA l/94-1GCCI SUNSTAR/ SERIES CART SOVEREIGN/900 SERIES CART MFG.
‘in. . : :: .:.. ~,: ‘:, :.,.: ,.~.~~ ,.. :L..~ ~~: .,.: : :..
Table of Contents Page Standard Fastener Identification Chart.. ..................................................... inside Front Cover Decals ...........................................................................................................
Pa&e& with Turbo Mfg. No. 1692257 6. Hitch and Tube Assembly - SunStar Series km 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Tube Assy. (Incl. Ref. No. 38) Nut, Hex Full, Lock, #lo-32 Washer, Plain, #l 0 Screw. Phillips, Truss Head, #10-32x l/2 Hose Clamp, 6” Decal, Cleaning Inst.
Cart Assembly NOTE: Sort out the hardware and arrange by size and type. Refer to figure 1. 1. Install the wheel assemblies (A, figure 2) to the frame (B). Place the head of the swivel wheel on the end of the frame. Align the holes and place four 3/8- 16 x 1 hex bolts up through the frame and head of the swivel.
6. Install the sleeve clamp (C, figure 11) to the connect- ing sleeve (A) with l/4-20 x l/Z slotted truss head screw (D) and nyloc nut (E). Install the connecting sleeve inside the collar of the cover and position sleeve clamp (C) over the support tube (B).
Discharge Tube Installation Landlord/1700 Series (Mfg. No. 1692095) 1. Install the spring clip (D, figure 18) with two 10-32 x i/2 truss head screws (E), four flat washers (F), and two locknuts (G). 2. Install l/4-20 x 5/8 carriage bolt (H) through hole in turbo housing.
Maintenance Operation * The cart cover IS subject to wear and detenora- tion. Check the cover frequently. Use an Grass should be cut often, and not too short. If grass is too long or lush it may be necessary to keep ground speed to a minimum or to cut only half the width to pre- vent clogging.
TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE TOLERANCE +20% SIZE 8-32 8-36 1 O-24 1 O-32 I/4-20 l/4-28 5/i 6-l 8 5/l 6-24 318-l 6 318-24 7116-14 7/l 6-20 l/2-13 I/2-20 9116-l 2 9/l 6-18 518-l 1 518-l 8 314-l 0 314-l 6 718-9 718-l 4 1-8 l-12 SAE GRADE #2 SAE GRADE #5 SAE GRADE #S 0 Q 8 In.
Een belangrijk punt na aankoop van elk apparaat Snapper TP 100-400 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Snapper TP 100-400 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Snapper TP 100-400 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Snapper TP 100-400 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Snapper TP 100-400 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Snapper TP 100-400 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Snapper TP 100-400 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Snapper TP 100-400 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.