Gebruiksaanwijzing /service van het product SLV-EZ44AZ, SLV-EZ22AZ, SLV-EZ11AZ van de fabrikant Sony
Ga naar pagina of 68
Video Cassette Recor der © 2000 by Son y Cor poration SL V -EZ44AZ/EZ22AZ SL V -EZ11AZ Operating Instructions 3-058-432- 11 (1) PAL NTSC 4.43.
Introduction 2 WARNING T o pr event fire or shock hazard, do not expose the unit to rain or moisture. T o avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only . The mains lead must only be changed at a qualified service shop.
3 Introduction * G-CODE is a register ed trademark of Gemstar Development Corporation. The G-CODE system is manufactured under license fr om Gemstar Development Corporation.
Getting Started 4 Getting Started Step 1 Unpacking Check that you have received the following items with the VCR: • Remote commander • R6 (size AA) batteries • Aerial cable Checking your model name The instructions in this manual are for the 3 models : SL V -EZ44AZ, EZ22AZ and EZ1 1AZ.
5 Getting Started Getting Started Step 2 Setting up the r emote commander T o operate the VCR a Sony TV Set TV / VIDEO to VIDEO and point at the remote sensor on the VCR TV and point at the remote sen.
Getting Started 6 Step 2: Setting up the remote commander (continued) Manufacturer Sony 01* 1 ,02 Akai 68 Blaupunkt 10 Ferguson 52 Grundig 1 1* 1 Hitachi 24 ITT/Nokia 15,16,69* 3 JVC 33* Loewe 45 Miva.
7 Getting Started Getting Started Y ou can use the WIDE button after entering a code number with any of the following marks; * 1 : Press WIDE to switch the wide pictur e mode on or off. * 2 : Press WIDE, then pr ess VOL +/ – to select the wide pictur e mode you want.
Getting Started 8 IN OUT AERIAL OUT IN AERIAL 1 Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the VCR. 2 Connect AERIAL OUT of the VCR and the aerial input of your TV using the supplied aerial cable. 3 Connect the mains lead to the mains.
9 Getting Started Getting Started Additional connections T o a TV that has audio/video input jacks This additional connection improves picture and sound quality . Connect the TV as shown on the right. If you want to use the T rinitron TV Synchro Play function (see page 33), this connection is necessary .
Getting Started 10 Step 4 T uning your TV to the VCR If you have connected your VCR to the TV using the audio/video cable, skip this step. 1 Press 1/u ON/ST ANDBY to turn on the VCR. 2 Press RF CHANNEL on the VCR. The factory-preset RF channel flashes in the display window for about three seconds.
11 Getting Started Getting Started SONY VIDEO CASSETTE RECORDER 5 T une the TV to the same channel as that shown in the display window so that the picture on the right appears on the TV screen. Refer to your TV manual for tuning instructions. If the pictur e does not appear clearly , see “ T o obtain a clear picture from the VCR ” below .
Getting Started 12 1 Press ? / 1 (on/standby) to turn on the VCR. 2 Press MENU, then pr ess > / . to move the cursor ( ” ) to CLOCK SET and press OK. MENU OK M / m / < / , Step 5 Setting the clock Y ou must set the time and date on the VCR to be able to use the timer recor ding features properly .
13 Getting Started Getting Started 3 Press M / m to set the date. The day of the week is set automatically . 4 Press , to flash the month and set the month using M / m . 5 Set the year , hour and minute in sequence, using , to flash the item to be set, and M / m to select the digits.
Getting Started 14 MENU PLAY OK Step 6 Pr esetting channels with the EASY G-CODE SET UP function (SL V - EZ44AZ/EZ22AZ only) The EASY G-CODE SET UP function is a feature that simplifies the channel presetting and the G-CODE guide channel setting.
15 Getting Started Getting Started T o check if the channels are pr eset correctly Set the TV to the video channel and press PROGRAM +/ – on the VCR. If the TV screen changes to a dif ferent pr ogramme each time you press PROGRAM +/ – , the channels are pr eset correctly .
Getting Started 16 Pr esetting channels (For SL V -EZ44AZ/EZ22AZ only) If you can receive no channels or only a few channels after performing the EASY G-CODE SET UP function (page 14), preset all receivable channels automatically using the One T ouch T uning function or the TUNER PRESET menu.
17 Getting Started Getting Started T o check if the channels are pr eset correctly Set the TV to the video channel and press PROGRAM +/ – on the VCR. If the TV screen changes to a dif ferent pr ogramme each time you press PROGRAM +/ – , the channels are pr eset correctly .
Getting Started 18 Presetting channels (continued) Presetting all r eceivable channels automatically Before you start … • T urn on the VCR and the TV . • Set the TV to the video channel. 1 Press MENU, then pr ess M / m to move the cursor ( B ) to TUNER PRESET and press OK.
19 Getting Started Getting Started continued PLAY OK 4 Press M / m to move the cursor ( B ) to AUTO PRESET , then press OK. All receivable channels ar e preset in numerical sequence. When no more receivable channels can be found, presetting stops and the pictur e from the lowest numbered channel is displayed on the TV screen.
Getting Started 20 Presetting channels (continued) PLAY OK PROG +/ – MENU OK M / m / < / , Presetting channels manually Before you start … • T urn on the VCR and the TV . • Set the TV to the video channel. 1 Press MENU, then pr ess M / m to move the cursor ( B ) to TUNER PRESET and press OK.
21 Getting Started Getting Started PLAY OK PLAY OK Selected programme position 5 Press PROG +/ – to select the pr ogramme position. 6 Press / repeatedly until the channel you want is displayed.
Getting Started 22 Disabling unwanted programme positions After presetting channels, you can disable unused pr ogramme positions. The disabled positions will be skipped later when you press the PROG +/ – buttons. (For SL V -EZ44AZ/EZ22AZ only) Y ou can also disable unwanted programme positions using the SET UP CH AND G-CODE menu (page 28).
23 Getting Started Getting Started PLAY OK MENU Setting up the G-CODE system manually (SL V - EZ44AZ/EZ22AZ only) The G-CODE system is a feature in Sony VCRs that simplifies programming the VCR to make timer recor dings. First, we recommend that you set up the G-CODE guide channels for your area using the EASY G-CODE SET UP function (page 14).
Getting Started 24 Setting up the G-CODE system manually (continued) SET UP CH AND G-CODE PROG CH SELECT GUIDE CH MOVE PROG ERASE PROG : [ CLEAR ] 9 : [ ] : [] 0 1 2 3 4 2 7 9 10 28 – – – – .
25 Getting Started Getting Started Setting up the G-CODE system for satellite broadcasts (if applicable) When your satellite tuner is connected via the AERIAL IN connector , first you have to set the programme position for each satellite channel using the TUNER PRESET menu.
Getting Started 26 Changing/ disabling pr ogramme positions (SL V - EZ44AZ/EZ22AZ only) After setting the channels and G-CODE guide channels, you can change the programme positions as you like. If any programme positions ar e unused or contain unwanted channels, you can disable them.
27 Getting Started Getting Started SET UP CH AND G-CODE PROG CH SELECT GUIDE CH SET GUIDE CH CONFIRM – – – – – : [] : [ ] : [ ] ] [ 0 1 2 3 4 9 7 10 28 10 28 2 7 9 2 PLAY OK 3 Press M / m until the selected channel and guide channel row moves to the desir ed programme position.
Getting Started 28 Changing/disabling programme positions (continued) 1 Press MENU, then pr ess > / . to move the cursor ( B ) to SET UP CH AND G-CODE and press OK. Disabling unwanted programme positions Note • Be sure to select the pr ogramme position you want to disable correctly .
29 Getting Started Getting Started CLEAR PLAY OK PLAY OK 2 Press > / . to move the cursor ( B ) to the row on which you want to disable. T o display other pages for programme position 5 to 49 (for Australia) or 6 to 50 (for New Zealand), pr ess > / .
Basic Operations 30 Playing a tape 1 T urn on your TV and set it to the video channel. 2 Insert a tape. The VCR turns on and starts playing automatically if you insert a tape with its safety tab r emoved.
31 Basic Operations Basic Operations PLAY OK If your TV is PA L NTSC 4.43 Set NTSC PB to PA L 4.43 3 Pr ess H PLA Y . When the tape reaches the end, it will r ewind automatically .
Basic Operations 32 Playing a tape (continued) SP APC T o use the time counter At the point on the tape that you want to find later , pr ess CLEAR. The counter in the display window r esets to “0:00:00.” Search for the point afterwar ds by referring to the counter .
33 Basic Operations Basic Operations T ur ning on the VCR and TV , and starting playback automatically (T rinitron TV Synchro Play) Y ou can only use this function if your TV is made by Sony (T rinitron TV).
Basic Operations 34 Recording TV pr ogrammes 1 T urn on your TV and set it to the video channel. 2 Insert a tape with its safety tab in place. 3 Press PROG +/– to select the programme position you want to recor d.
35 Basic Operations Basic Operations LP APC 4 Press SP/LP to select the tape speed, SP or LP . LP (Long Play) provides recording time twice as long as SP (Standard Play), however , SP produces better pictur e and audio quality . 5 Press z REC to start recor ding.
Basic Operations 36 Safety tab T o save a r ecording T o prevent accidental erasure, br eak off the safety tab as illustrated. T o recor d on the tape again, cover the tab hole with adhesive tape. Tips • T o select a programme position, you can use the programme number buttons on the remote commander .
37 Basic Operations Basic Operations SP STOP APC PROGRAM +/– Recording TV pr ogrammes using the Easy Timer function The Easy T imer function allows you to make a timer r ecording of a pr ogramme without turning on your TV .
Basic Operations 38 Recor ding TV pr ogrammes using the Easy T imer function (continued) 4 Set the r ecor ding stop time in the same way as in step 2, then press the EASY TIMER knob. A programme number flashes. 5 T urn the EASY TIMER knob clockwise or counterclockwise to select the programme you want to r ecor d.
39 Basic Operations Basic Operations 1 • When “–:– –” is displayed in the display window , press the EASY TIMER knob. • T o change the clock setting, press and hold the EASY TIMER knob on the VCR for more than thr ee seconds. The CLOCK indicator and the curr ent clock setting appear in the display window .
Basic Operations 40 3 Pr ess the EASY TIMER knob to confirm the clock setting. The VCR enters the timer r ecor ding setting mode. T o continue the Easy Timer setting, go to step 2 in “Setting the Easy T imer” on page 37.
41 Basic Operations Basic Operations T o stop r ecording T o stop the VCR while recording, pr ess x STOP . T o check or change the timer setting Pr ess the EASY TIMER knob repeatedly until the setting you want to check or change flashes. Then re-enter the new setting, if necessary .
Basic Operations 42 Tip • T o recor d from a sour ce connected to LINE-1 IN jacks, press INPUT SELECT or PROG +/– or turn the EASY TIMER knob to display “L” in the display window . Notes • Y ou cannot set the Easy T imer if eight programmes have alr eady been set.
43 Basic Operations Basic Operations Recording TV pr ogrammes using the G-CODE system (SL V - EZ44AZ/EZ22AZ only) Just enter the G-CODE number , listed in the TV programme guide, for the programme you want to recor d. The date, times and programme position of that pr ogramme are set automatically .
Basic Operations 44 Recor ding TV pr ogrammes using the G-CODE system (continued) PLAY OK 123 456 789 0 2 Pr ess the programme number buttons to enter the G-CODE number for the pr ogramme you want to recor d. If you make a mistake, press CLEAR and r e-enter the correct number .
45 Basic Operations Basic Operations T o stop r ecording T o stop the VCR while recording, pr ess p STOP . T o r ecord satellite broadcasts When you connect the satellite tuner and the VCR, you can recor d satellite pr ogrammes using the G-CODE number if applicable.
Basic Operations 46 PLAY OK Setting the timer manually Y ou can preset up to eight programmes at a time. Befor e you start… • Check that the VCR clock is set to the corr ect time. • Insert a tape with its safety tab in place. Make sure the tape is longer than the total recor ding time.
47 Basic Operations Basic Operations PLAY OK Tips • T o set the programme position, you can also use the PROG +/– or pr ogramme number buttons. • T o set the tape speed, you can also use the SP/LP button. Note • The t indicator flashes in the display window when you pr ess ? / 1 with no tape inserted.
Additional Operations 48 Additional Operations Playing/sear ching at various speeds m 3 REW M # FF H PLAY y SLOW Playback options V iew the picture during fast- forward or r ewind Play at high speed Play at twice the normal speed Play in slow motion Play frame by frame Rewind and start play T o r esume normal playback Pr ess H PLA Y .
Additional Operations 49 SP APC Setting the recor ding duration time After starting recor ding in the normal way , you can have the VCR stop recor ding automatically after a specified duration. 1 While recording, press z REC. The t indicator appears in the display window .
Additional Operations 50 Checking/ changing/ cancelling timer settings Before you start… • T urn on your TV and set it to the video channel. 1 Pr ess ? / 1 to turn on the VCR. 2 Pr ess MENU, then select TIMER SET/CHECK: • If you want to change or cancel a setting, go on to the next step.
Additional Operations 51 3 Press M / m to select the setting you want to change or cancel: • T o change the setting, press < / , to flash the item you want to change, and pr ess M / m to r eset it. Then, press , repeatedly until the cursor ( ” ) appears at the beginning of the line.
Additional Operations 52 SEARCH Searching the beginning of an Easy Timer r ecor ded pr ogramme If you r ecor d a pr ogramme using the Easy T imer function, you can easily find the beginning of the recor ding with this SEARCH function. The SEARCH indicator flashes when the VCR finishes the Easy T imer r ecor ding.
Additional Operations 53 SEARCH INDEX 8 Sear ching using the index function The VCR marks the tape with an index signal at the point wher e each recording begins. Use these signals as refer ences to find a specific r ecording. The VCR can search up to 99 index signals ahead of or behind the curr ent position.
Additional Operations 54 Using the SEARCH button and EASY TIMER knob on the VCR 1 Press SEARCH on the VCR r epeatedly until “ INDEX ” appears in the display window (the SEARCH indicator lights up).
Additional Operations 55 Adjusting the picture Adjusting the tracking Although the VCR automatically adjusts the tracking when playing a tape (the indicator flashes in the display window , then goes off), distortion may occur if the tape was r ecor ded in poor condition.
Additional Operations 56 Changing menu options 1 Press MENU, then select SET UP MENU. 2 Press M / m to select the option to change, then press < / , to change the setting. 3 Press OK to return to the original scr een. Menu choices Initial settings ar e indicated in bold print.
Additional Operations 57 Editing with another VCR How to connect to record on this VCR Tip • Connect LINE-1 IN on this VCR to the line output jacks on the other VCR using a commercially available audio/video cable such as Sony VMC-710HG/720HG (not supplied).
Additional Operations 58 Operation (when r ecording on this VCR) Before you start editing • T urn on your TV and set it to the video channel. • Press INPUT SELECT or PROG +/ – to display “ L ” in the display window . • Press SP/LP to select the tape speed.
59 Additional Information Symptom The ?/1 ON/ST ANDBY switch does not function. The power is turned on but the VCR does not operate. The clock has stopped and “–:– –” lights in the display window . The playback picture does not appear on the TV screen.
60 Additional Information T roubleshooting (continued) Recording Timer recording Symptom No TV programmes appear on the TV screen. TV r eception is poor. The tape starts playing as soon as it is inserted. The tape is ejected when you pr ess z REC. Nothing happens when you pr ess z REC.
61 Additional Information terminal initial contamination Symptoms caused by contaminated video heads • Normal pictur e • Rough picture • Unclear picture • No pictur e (or black & white scr.
62 Additional Information Specifications System Channel coverage COUNTRY is set to AUS: VHF AS0 to AS12, AS5A, AS9A UHF AS28 to AS69 CA TV S01 to S05, S1 to S41 COUNTRY is set to NZ: VHF NZ1 to NZ11 U.
63 Additional Information Index to parts and contr ols Front panel Refer to the pages indicated in parentheses ( ) for details. 1 ?/1 ON/ST ANDBY switch (10) 2 Remote sensor (5) 3 T ape compartment 4 .
64 Additional Information Display window 1 T imer indicator (38, 47) 2 T ape speed indicator (35) 3 CLOCK indicator (39) 4 ST AR T indicator (37) 5 STOP indicator (37) 6 APC (Adaptive Picture Control).
65 Additional Information Rear panel (SL V -EZ44AZ) Rear panel (SL V -EZ22AZ/EZ11AZ) 2 1 3 4 5 1 Mains lead (8) 2 LINE-1 IN AUDIO/VIDEO jacks (57) 3 AERIAL IN connector (8) 4 AERIAL OUT connector (8) .
66 Additional Information Index to parts and controls (continued) Remote commander 1 TV / VIDEO r emote contr ol switch (5) 2 Z EJECT button (31) 3 TRINITRON TV SYNCHRO PLA Y button (33) 4 DISPLA Y bu.
67 Additional Information qd ?/1 (on/standby) switch (44, 47) qf G-CODE button (43) (SL V -EZ44AZ/EZ22AZ only) qg CLEAR button (32, 44) qh Programme number/ ? (ten’s digit) buttons (36, 40, 44) qj PROG (programme) +/– buttons (34) qk VOL (volume) +/– buttons (for TV) ql .
Sony Corporation Printed in Malaysia A, B Accessories supplied 4 Adjusting picture 22, 48, 55 tracking 48, 55 Aerial hookup 8 AFT (Auto Fine T uning) 22 APC (Adaptive Picture Control) 55 A V (audio/vi.
Een belangrijk punt na aankoop van elk apparaat Sony SLV-EZ44AZ, SLV-EZ22AZ, SLV-EZ11AZ (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sony SLV-EZ44AZ, SLV-EZ22AZ, SLV-EZ11AZ heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sony SLV-EZ44AZ, SLV-EZ22AZ, SLV-EZ11AZ vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sony SLV-EZ44AZ, SLV-EZ22AZ, SLV-EZ11AZ leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sony SLV-EZ44AZ, SLV-EZ22AZ, SLV-EZ11AZ krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sony SLV-EZ44AZ, SLV-EZ22AZ, SLV-EZ11AZ bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sony SLV-EZ44AZ, SLV-EZ22AZ, SLV-EZ11AZ kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sony SLV-EZ44AZ, SLV-EZ22AZ, SLV-EZ11AZ . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
