Gebruiksaanwijzing /service van het product SLV-SE45UX van de fabrikant Sony
Ga naar pagina of 76
Video Cassette Recor der ©1999 by Sony Corporation SL V -SE30UX SL V -SE45UX Operating Instructions 3-865-361- 12 (1) P AL NTSC 4.43.
Introduction 2 WARNING T o pr event fire or shock hazard, do not expose the unit to rain or moisture. T o avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only . Mains lead must only be changed at a qualified service shop.
3 Introduction T able of contents Getting Started * VIDEO Plus+ and PlusCode are trademarks applied for by Gemstar Development Corp. VIDEO Plus+ system is manufactured under license fr om Gemstar Development Corporation.
Getting Started 4 Getting Started Step 1 Unpacking Check that you have received the following items with the VCR: Checking your model name The instructions in this manual are for the 2 models: SL V -SE30UX and SE45UX. Check your model number by looking at the rear panel of your VCR.
Getting Started 5 Getting Started Step 2 Setting up the r emote commander Inserting the batteries Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment. Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position.
Getting Started 6 Step 2 : Setting up the remote commander (continued) F ASTEXT buttons V ; WIDE … TV/VIDEO I/ u DISPLA Y Á +/– Programme number buttons TV control buttons To T urn the TV into st.
Getting Started 7 Getting Started Notes • W ith normal use, the batteries should last about three to six months. • If you do not use the remote commander for an extended period of time, r emove the batteries to avoid possible damage from battery leakage.
Getting Started 8 Code number 01* 1 , 02 68 52 10* 1 , 1 1* 1 24 33 45 09, 70 66 15, 16, 69* 3 Step 2 : Setting up the remote commander (continued) Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the one that works with your TV .
Getting Started 9 Getting Started Step 3 Connecting the VCR If your TV has a EURO-A V connector , see page 10. If your TV does not have a EURO-A V (Scart) connector : Signal flow AERIAL IN Aerial cable (supplied) AERIAL IN AERIAL OUT to mains 1 Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the VCR.
Getting Started 10 Step 3 : Connecting the VCR (continued) If your TV has a EURO-A V (Scart) connector 1 Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the VCR. 2 Connect AERIAL OUT of the VCR and the aerial input of your TV using the supplied aerial cable.
Getting Started 11 Getting Started 3 Connect LINE-1 (TV) on the VCR and the EURO-A V (Scart) connector on the TV with the optional EURO-A V cable. This connection impr oves picture and sound quality . Whenever you want to watch the VCR picture, pr ess … TV/ VIDEO to display the VIDEO indicator in the display window .
Getting Started 12 • TV Direct Rec Y ou can easily recor d what you are watching on the TV (other than tapes being played on this VCR). For details, see “Recording what you ar e watching on the TV (TV Direct Rec)” on page 41. • One T ouch Play W ith One T ouch Play , you can start playback automatically without turning on the TV .
Getting Started 13 Getting Started Step 4 Setting up the VCR with the Auto Set Up function Before using the VCR for the first time, set up the VCR using the Auto Set Up function. W ith this function, you can set TV channels, guide channels for the VIDEO Plus+ system, the RF channel, and VCR clock automatically .
Getting Started 14 Step 5 T uning your TV to the VCR If you have connected the VCR to your TV using the EURO-A V cable, skip this step. 1 Press RF CHANNEL on the VCR lightly . The factory-preset RF channel appears in the display window . The VCR signal is output through this channel to the TV .
Getting Started 15 Getting Started 3 T une the TV to the same channel as that shown in the display window so that the picture on the right appears clearly on the TV screen. Refer to your TV manual for tuning instructions. If the pictur e does not appear clearly , see “T o obtain a clear picture from the VCR” below .
Getting Started 16 Selecting a language If you prefer an on-scr een language other than English, use the on-screen display to select another language. Before you start… • T urn on the VCR and the TV . • Set the TV to the video channel. > / . OK MENU 1 Press MENU, then pr ess > / .
Getting Started 17 Getting Started 4 Press MENU to exit the menu. Tip • If you want to return to the pr evious menu, highlight RETURN and press OK. Note • The menu disappears automatically if you don’t pr oceed for more than a few minutes.
Getting Started 18 Selected programme position • PROG Pr esetting channels If some channels could not be preset using the Auto Set Up function, you can preset them manually . Before you start… • T urn on the VCR and the TV . • Set the TV to the video channel.
Getting Started 19 Getting Started 4 Press > / . to highlight CHANNEL SET , then pr ess OK. 5 Press > / . repeatedly until the channel you want is displayed. The channels appear in the following order: • UHF B21 - B69 If you know the number of the channel you want, press the pr ogramme number buttons.
Getting Started 20 Selected programme position If the picture is not clear Normally , the Auto Fine T uning (AFT) function automatically tunes in channels clearly .
Getting Started 21 Getting Started 1 Press MENU, then pr ess > / . to highlight LISTS and press OK. 2 Press > / . to highlight CHANNEL LIST , then pr ess OK. Changing/ disabling pr ogramme positions After setting the channels, you can change the programme positions and the station names as you like.
Getting Started 22 Changing/disabling programme positions (continued) 3 Press > / . to highlight the r ow on which you want to change the programme position, then press / . T o display other pages for programme positions 6 to 60, press > / . r epeatedly .
Getting Started 23 Getting Started 1 Press MENU, then pr ess > / . to highlight LISTS and press OK. 2 Press > / . to highlight CHANNEL LIST , then pr ess OK. 3 Press > / . to highlight the row on which you want to change the station name, then pr ess / .
Getting Started 24 Changing/disabling programme positions (continued) 4 Press / . 5 Enter the station name. 1 Press > / . to select a character . Each time you press > , the character changes as shown below . A n B n … n Z n a n b n … n z n 0 n 1 n … n 9 n (symbols) n (blank space) n A 2 Press / to set the next character .
Getting Started 25 Getting Started Disabling unwanted programme positions After presetting channels, you can disable unused programme positions. The disabled positions will be skipped later when you press the PROG +/– buttons. Before you start… • T urn on the VCR and the TV .
Getting Started 26 2 Press > / . to highlight CHANNEL LIST , then press OK. 3 Press > / . to highlight the r ow on which you want to disable. 4 Press CLEAR. The selected row will be clear ed as shown on the right. 5 Repeat steps 3 and 4 for any other programme positions you want to disable.
Getting Started 27 Getting Started Setting the clock Y ou must set the time and date on the VCR to use the timer r ecording features properly . If the VCR clock was not set in the Auto Set Up procedure, you need to set it manually . The Auto Clock Set function works only if a station in your area is br oadcasting a time signal.
Getting Started 28 Setting the clock (continued) 3 Press > / . to highlight MANUAL ADJUST , then pr ess OK. 4 Press > / . to set the date. 5 Press / to highlight the month and set the month pressing > / . . 6 Set the year , hour , and minutes in sequence, pressing / to highlight the item to be set, and press > / .
Getting Started 29 Getting Started MENU OK PLAY 7 Press OK to start the clock. 8 Press MENU to exit the menu. continued Tips • T o change the digits during setting, press ? to r eturn to the item to be changed, and select the digits pressing > / .
Getting Started 30 1 Press MENU, then pr ess > / . to highlight SETTINGS and press OK. 2 Press > / . to highlight CLOCK, then press OK. AUTO ADJUST is highlighted. 3 Press OK. Changing the station for the Auto Clock Set function Before you start… • T urn on the VCR and the TV .
Getting Started 31 Getting Started 4 Press > / . to highlight ON, then press OK. 5 Press . to highlight CLOCK PROG, then press OK. 6 Press > / . repeatedly until the programme position of the station that carries the time signal appears. If the VCR does not receive the time signal from any station, AUTO ADJUST returns to OFF automatically .
Getting Started 32 1 Hold down P P AUSE and I / u ON/ ST ANDBY on the VCR simultaneously for more than thr ee seconds. Setting your personal code For identification, you can enter a personal code into the VCR. Once you enter your personal code, you can confirm it any time but can never change it.
Getting Started 33 Getting Started 2 Enter your personal code. 1 Press > / . to select a character . Each time you pr ess > , the character changes as shown below . A n B n … n Z n 0 n 1 n … n 9 n (blank space) n – (hyphen) n A 2 Press / to set the next character .
Basic Operations 34 Basic Operations Playing a tape 6 EJECT 1 T urn on your TV and set it to the video channel. 2 Insert a tape. The VCR turns on and starts playing automatically if you insert a tape with its safety tab removed.
Basic Operations Basic Operations 35 Set NTSC PB to ON P AL TV NTSC 4.43 Additional tasks To Stop play Pause play Resume play after pause Fast-forward the tape Rewind the tape Eject the tape Press p S.
Basic Operations 36 Notes • The counter r esets to “0:00:00” whenever a tape is reinserted. • The counter stops counting when it comes to a portion with no r ecording. • The time counter does not appear on the TV scr een when using an NTSC-recorded tape.
Basic Operations Basic Operations 37 Recor ding TV pr ogrammes r REC PROG +/– SP/LP 1 T urn on your TV and set it to the video channel. 2 Insert a tape with its safety tab in place.
Basic Operations 38 Recording TV pr ogrammes (continued) 3 Press INPUT SELECT until a pr ogramme position number appears in the display window . 4 Press PROG +/– to select the pr ogramme position you want to recor d. 5 Press SP/LP to select the tape speed, SP or LP .
Basic Operations Basic Operations 39 Safety tab T o check the remaining time Press DISPLA Y . W ith the display on, press COUNTER/REMAIN to check the remaining time. Each time you pr ess COUNTER/REMAIN, the time counter and the remaining time appear alternately .
Basic Operations 40 Recording TV pr ogrammes (continued) Tips • T o select a programme position, you can use the programme number buttons on the remote commander . For two-digit numbers, press the ? (ten’s digit) button followed by the programme number buttons.
Basic Operations Basic Operations 41 Recording what you ar e watching on the TV (TV Direct Rec) If you use the SMAR TLINK connection, you can easily record what you ar e watching on the TV (other than tapes being played on the VCR). 1 Insert a tape with its safety tab in place.
Basic Operations 42 1 Press TIMER. • When you set TIMER OPTIONS to V ARIABLE The TIMER METHOD menu appears on the TV screen. Pr ess > / . to select VIDEO PLUS+, then press OK. • When you set TIMER OPTIONS to VIDEO PLUS+ The VIDEO PLUS+ menu appears on the TV screen.
Basic Operations Basic Operations 43 2 Press the pr ogramme number buttons to enter the PlusCode number . If you make a mistake, press CLEAR and re-enter the corr ect number . 3 Press OK. The date, start and stop times, programme position, tape speed, and VPS/PDC setting appear on the TV screen.
Basic Operations 44 T o stop recording T o stop the VCR while recor ding, press p STOP . Daily/weekly recor ding In step 4 above, press . to select the r ecording pattern. Each time you press . , the indication changes as shown below . Press > to change the indication in reverse or der .
Basic Operations Basic Operations 45 Timer recor ding with VPS/PDC signals Some broadcast systems transmit VPS (V ideo Programme System) or PDC (Programme Delivery Contr ol) signals with their TV programmes.
Basic Operations 46 Tips • T o set the programme position with a two digit number , press ? (ten’s digit) button followed by the programme number button. • T o set the programme position, you can also use the PROG +/– or programme number buttons.
Basic Operations Basic Operations 47 1 Press TIMER. • When you set TIMER OPTIONS to V ARIABLE The TIMER METHOD menu appears on the TV scr een. Press > / . to select ST ANDARD, then press OK. • When you set TIMER OPTIONS to ST ANDARD The TIMER menu appears on the TV screen.
Basic Operations 48 Setting the timer manually (continued) 2 Set the date, start and stop times, programme position, tape speed, and VPS/PDC function: 1 Press / to highlight each item in turn. 2 Press > / . to set each item. T o correct a setting, press ? to return to that setting and reset.
Basic Operations Basic Operations 49 Daily/weekly recor ding In step 2 above, press . to select the r ecording pattern. Each time you press . , the indication changes as shown below . Press > to change the indication in reverse or der . Tips • T o set the programme position, you can also use the PROG +/– or pr ogramme number buttons.
Additional Operations 50 Additional Operations Playing/sear ching at various speeds Playback options V iew the picture during fast-forward or r ewind Play at high speed Play at twice the normal speed Play in slow motion × 2 & SLOW )# FF · PLA Y Operation During fast-forward, hold down )# FF/ ) FF .
51 Additional Operations Playback options Play frame by frame Rewind and start play Operation During pause, press )# FF or 03 REW on the remote commander . Hold down )# FF or 03 REW to play one frame each second. During stop, press · PLA Y on the VCR while holding down 03 REW/ 0 REW on the VCR.
Additional Operations 52 T o use the shuttle ring in jog mode Use this mode for frame-by-frame playback. Press JOG to enter the jog mode. The JOG button lights up. If you change to the jog mode during any playback mode, the playback pauses so you can see a still picture.
53 Additional Operations Setting the recor ding duration time After starting recor ding in the normal way , you can have the VCR stop recor ding automatically after a specified duration. 1 While recor ding, press r REC. The indicator appears in the display window .
Additional Operations 54 1 Press I / u to turn on the VCR. 2 Press MENU, then pr ess > / . to highlight LISTS and press OK. 3 Press > / . to highlight TIMER LIST , then press OK: • If you want to change or cancel a setting, go on to the next step.
55 Additional Operations Programme 1 Programme 2 Programme 1 Programme 2 about 20 seconds will be cut off will be cut off 4 Press > / . to select the setting you want to change or cancel, then press OK. The selected setting appears in the TIMER menu.
Additional Operations 56 SMART SEARCH > / . / ? / / OK Sear ching using the Smart Sear ch function If you recor d multiple programmes on a tape, use the Smart Search function to see what has been recor ded on your tape. Y ou can see information such as date, time, and channel of programmes recor ded on a tape.
57 Additional Operations continued T o stop searching Press p ST OP . T o exit the SMART SEARCH screen Press SMAR T SEARCH. T o record in a blank space Blank space on the tape will appear as a blank row in the SMAR T SEARCH screen. Select the blank r ow in step 3, then press OK.
Additional Operations 58 AB C AD C Searching using the Smart Sear ch function (continued) Notes • If you begin r ecording a programme “D” from the middle of a pr eviously recorded programme “A.
59 Additional Operations Sear ching using the index function The VCR marks the tape with an index signal at the point where each r ecording begins. Use these signals as refer ences to find a specific recor ding. = / + INDEX SEARCH 1 Insert an indexed tape into the VCR.
Additional Operations 60 Adjusting the pictur e Adjusting the tracking Although the VCR automatically adjusts the tracking when playing a tape (the indicator flashes in the display window , then goes off), distortion may occur if the tape was recor ded in poor condition.
61 Additional Operations Tip • T o set tracking to the centre position, pr ess the TRACKING + and – buttons at the same time. Notes • Y ou can adjust the tracking for the NTSC-recor ded tape but the tracking meter won’t be displayed. • W ith the Auto Long Play function on, the OPC function will work only in SP mode.
Additional Operations 62 Changing menu options 1 Press MENU, then select OPTIONS and press OK. 2 Press > / . to highlight OPTIONS-1 or OPTIONS-2, then pr ess OK. 3 Press > / . to select the option, then pr ess OK. 4 Press > / . to change the setting, then pr ess OK.
63 Additional Operations Menu option OPC AUTO LONG PLA Y T APE LENGTH Set this option to • ON to switch on the OPC (Optimum Picture Contr ol) function and improve picture quality .
Additional Operations 64 This VCR (Recorder) LINE-2 IN VIDEO/AUDIO VMC-710HG/720HG audio/video cable (not supplied) TV Other VCR (Player) Editing with another VCR How to connect to recor d on this VCR Tip • Y ou can also use the LINE-1 (TV) connector instead.
65 Additional Operations Operation (when recor ding on this VCR) Before you start editing • T urn on your TV and set it to the video channel. • Press INPUT SELECT to display “L2” (“L1” or “L3”) in the display window . • Press SP/LP to select the tape speed, SP or LP .
66 Additional Information T roubleshooting If you have any questions or problems not cover ed below , please consult your nearest Sony service facility .
67 Additional Information Symptom The picture r olls vertically during picture sear ch. The picture has no sound. No TV programme appears on the TV screen. TV reception is poor . The tape starts playing as soon as it is inserted. The tape is ejected when you press r REC.
68 Additional Information Symptom A tape cannot be inserted. The remote commander does not function. The SMAR TLINK function does not work. The tracking meter does not appear on the TV screen. Y ou cannot control other TVs. The VCR needs to be cleaned.
69 Additional Information Specifications System Channel coverage P AL (I) UHF B21 to B69 RF output signal UHF channels 21 to 69 Aerial out 75-ohm asymmetrical aerial socket Inputs and outputs : LINE-1.
70 Additional Information Index to parts and contr ols Refer to the pages indicated in parentheses ( ) for details. Front panel (SL V -SE30UX) 9 r REC (recor d) button (38, 53, 65) 0 Remote sensor (5).
71 Additional Information Front panel (SL V -SE45UX) 9 p ST OP button (35, 65) 0 P P AUSE button (32, 35, 65) !¡ r REC (recor d) button (38, 53, 65) !™ Remote sensor (5) !£ AUTO SET UP/ RF (Radio .
72 Additional Information Index to parts and controls (continued) Display window 1 T imer indicator (44, 48) 2 T ape speed indicators (38) 3 VIDEO indicator (1 1, 39) 4 VPS (V ideo Programme System)/ .
73 Additional Information Rear panel 1 Mains lead (9, 10) 2 AERIAL IN ANTENNE ENTREE connector (9, 10) 3 AERIAL OUT ANTENNE SOR TIE connector (9, 10) 4 … LINE-3 IN … ENTREE LIGNE-3 connector (64) .
74 Additional Information Index to parts and controls (continued) Remote commander 1 6 ␣ EJECT button (35) 2 WIDE button ( for TV ) (7) 3 AUDIO MONITOR button ( for TV ) (7) 4 × 2 button* (50) 5 & ␣ SLOW button* (50) 6 SP (Standar d Play)/LP (Long Play) button (38) 7 DISPLA Y button (39) 8 ? (ten’s digit) button (6, 40) 9 .
75 Additional Information !£ TV / VIDEO remote contr ol switch (5) !¢ I / u (on/standby) switch (6, 44) !∞ COUNTER/REMAIN button (39) V (T eletext) button (for TV) (7) !§ ; TV power on/TV mode se.
A, B Adjusting picture 20, 60 tracking 60 Aerial hookup 9 AFT (Auto Fine T uning) 20 Auto Clock Set 30 Auto Long Play 63 Auto Set Up 13 C Changing the programme position 21 Changing the station name 2.
Een belangrijk punt na aankoop van elk apparaat Sony SLV-SE45UX (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sony SLV-SE45UX heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sony SLV-SE45UX vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sony SLV-SE45UX leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sony SLV-SE45UX krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sony SLV-SE45UX bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sony SLV-SE45UX kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sony SLV-SE45UX . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
