Gebruiksaanwijzing /service van het product 211376A van de fabrikant Spalding
Ga naar pagina of 18
1 05/03 P/N 211376A Customer Service N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A. A Huffy Comp any WRITE IN YOUR MODEL NUMBER: __________ REQUIRED TOOLS AND MA TERIALS: • Two People • Tape Measure • Tape • Shovel and Spade • Concrete, 900 lb.
2 P/N 211376A 05/03 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est fit large bolt s into large holes of elevator tubes, backboard bracket s and triangle plates.
05/03 P/N 211376A 3 F AILURE TO FOLLOW THESE W ARNINGS MA Y RESUL T IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NO T HANG on the rim or any part of the system including bac kboard, suppor t braces or net.
4 P/N 211376A 05/03 IMPORT ANT! WRITE MODEL NUMBER FROM BOX ONTO P AGE 1 OF THIS OWNERS MANUAL 1. Make sure ground is level with playing surface, then dig pole hole. 2. CONTACT UTILITIES BEFORE DIGGING. W ARNING! Correctly identify each pole section and mark indicated distance from ends with tape.
05/03 P/N 211376A 5 5. Fill hole approximately 3/4 full with concrete. Tamp down concrete to release air pockets. PLAYING SURFACE Insert bottom pole section (3) into ground sleeve (4). 3. 4. Assemble clamps (7) around bottom pole and ground sleeve (4) as shown.
6 P/N 211376A 05/03 6. Insert ground sleeve (4) and pole section (3) into hole. Fill remaining hole with concrete. Tamp down concrete to release air pockets and build drainage hill. Center and level ground sleeve assembly in hole. Check leveling on all sides several times while concrete is curing.
05/03 P/N 211376A 7 C O N C R E T E 1" (2.54cm) IMPORT ANT! Bounce pole top (1) and middle section (2) together as shown until they no longer move toward taped reference mark. NOTE: Pole sections should have a 4-1/2" (11.4 cm) minimum overlap.
8 P/N 211376A 05/03 14. Lower clamp cover (12) over clamps and snap into proper position. 13. Secure clamps (7) around pole section as shown. Refer to Step 4. Tighten completely. 12. 11 12 12 3 12 IMPORT ANT! ELEVATOR HOLES MUST BE PARALLEL WITH PLAYING SURFACE.
05/03 P/N 211376A 9 F R O N T 17 14 19 13 18 16 14 15 15 18 14 15. Beginning with top hole in left and right screw jack support plates (16 & 17), install elevator tubes (15) to pole as shown. Then secure lower holes in support plates to pole. NOTE: Not all holes in support plates (16 & 17) are used in this assembly.
10 P/N 211376A 05/03 1 7 9 8 11 7' 2.1m 20 22 21 24 24 IMPORT ANT! DO NOT OVER TIGHTEN. 23 POLE 14 18 18 21 15 15 16 17 14 17. 18. Center screw jack (21) between support plates (16 & 17) and secure as shown below. Attach logo label (22) to height indicator cover (23).
05/03 P/N 211376A 11 ½ 13 14 18 14 15 15 26 26 Secure upper elevator tubes (15) to pole assembly as shown. 19. Insert spacer (25) through top holes of height indicator cover (23) and screw jack assembly as shown. Align spacer (25) and screw jack assembly between elevator tubes (15) and secure.
12 P/N 211376A 05/03 7' 2.1m 18 14 30 30 14 30 30 14 18 18 18 14 14 14 27 15 15 15 15 28 28 22. NOTE: Two people recommended for this operation. Attach Y-frame support bracket (27) to elevator tubes (15) as shown. NOTE: Same hardware used for upper and lower installation.
05/03 P/N 211376A 13 ½ 29 28 27 23. Lift backboard upright and insert bolt (28) heads into key slots. Slide backboard downward to position bolt (28) into channel as shown. Align rim mounting holes on Y-frame support bracket (27) to rim holes on backboard and tighten completely.
14 P/N 211376A 05/03 24. 25. ½ 33 31 29 Attach rim (33). Note: Mounting nuts (29) and bolts (31) supplied with rim hardware. USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF NET CLIPS, OR WHEN ALL NET CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM.
05/03 P/N 211376A 15 Position looped end of height adjustment crank (36) onto hook as shown. Rotate crank handle to raise or lower backboard. View label (20) to determine approximate backboard height. 27. 26. Height Adjustment HOOK 36 20 STORE CRANK OUT OF REACH OF CHILDREN.
16 P/N 211376A 05/03 H U FFY HUFFY SP ORTS 10 feet (3.05 m) 37 REGULATION RIM HEIGHT IS 10 FEET (3.05 M). 28. Apply height adjustment label (37) to front of pole as shown.
05/03 P/N 211376A 17 P ARTS LIST HARDW ARE IDENTIFIER * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. Item Qty. Part No. Description 1 1 900757 Top Pole Section 2 1 900874 Middle Pole Section, Flared End 3 1 908215 Bottom Pole Section 4 1 206500 Ground Sleeve, Square 5 2 201124 Lock Nut, Hex Head, 3/8 x 16 6 4 203232 Washer, Flat, 3/8 x 3/4 O.
18 P/N 211376A 05/03 HARDW ARE IDENTIFIER (CONTINUED) * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. Item #25 (1) Item #29 (6) Item #30 (4) Item #31 (4) Item #34 (12*) Item #28 (2) Item #26 (2) Item #24 .
Een belangrijk punt na aankoop van elk apparaat Spalding 211376A (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Spalding 211376A heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Spalding 211376A vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Spalding 211376A leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Spalding 211376A krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Spalding 211376A bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Spalding 211376A kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Spalding 211376A . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
