Gebruiksaanwijzing /service van het product M60 1111 van de fabrikant Spalding
Ga naar pagina of 28
1 08/05 P/N M601111 © COPYRIGHT 2005 by SPALDING H U F F Y HUFFY SPOR TS Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-632 7921 Internet Address: http://www.
2 P/N M601111 08/05 10-3/4" High 4" Wide PMS 021 for W arning Owner must ensure that all players know and follow these rules for safe operation of the system. W ARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net.
08/05 P/N M601111 3 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY.
4 P/N M601111 08/05 For more information on assembly, placement, proper use, and maintenance, visit The American Basketball Council website at http://www.smarthoops.com. IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p art s are p acked inside.
08/05 P/N M601111 5 Get to know the basic parts of your basketball system... FRONT T OP POLE BACK MIDDLE POLE FRONT COVER RIM BOTT OM POLE STRUTS ELEV A TOR ASSEMBL Y BACKBOARD BASE WHEEL CARRIAGE ASS.
6 P/N M601111 08/05 Item #14 (2) 203099Hex Locknut (Nylon Insert) 5/16-18 Item #47 (6)* Item #31 (4) Item #50 (4) Item #1 1 (15)* Item #10 (18)* Item #43 (2) Item #21 (7) HARDW ARE IDENTIFIER (NUTS, W ASHERS & MET AL SP ACERS) Item #30 (4) Item Qty .
08/05 P/N M601111 7 HARDW ARE IDENTIFIER (BOL TS & SCREWS) Item #55 (1) Item #9 (6) Item #57 (6) Item #41 (2) 200520 - #8 x 3/4 Screw Item #19 (1) Item #29 (4) Item #22 (2) Item #49 (1) Item #13 (2) Item #54 (2) Item #15 (4) Item #46 (6) 201596 Screw 1/4 x 1.
8 P/N M601111 08/05 TOOLS REQUIRED FOR THIS SECTION Item #61 (1) Item #62 (1) Item #64 (1) Item #66 (1) Item #63 (1) Item #65 (1) HARDW ARE IDENTIFIER (RIM) SECTION A: ASSEMBLE THE POLES W ood Board (.
08/05 P/N M601111 9 2. WOOD SCRAP (NOT SUPPLIED) 2 Bounce middle pole (2) into top pole section (1) using a wood scrap as shown until top pole no longer moves toward pole identification mark on middle pole.
10 P/N M601111 08/05 Align dimple of middle pole with slot of bottom pole.While maintaining alignment, bounce top and middle pole assembly (1 & 2) onto lower pole section (3) as shown until they no longer move toward pole identification mark.
08/05 P/N M601111 11 T OOLS REQUIRED FOR THIS SECTION SECTION B: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: Hammer or Mallet (2) 1/2”W renches 1/2.
12 P/N M601111 08/05 11 15 10 2. Attach pole assembly to base using carriage bolts (15) washers(10) and nuts (1 1) as shown. T wo people are required for this step. 1. johnn y sees aw Assemble pole bracket (12) using bolt (13) and Lock Nut (14) as shown.
08/05 P/N M601111 13 3. Rotate non-secured ends of t ank struts (16) outward to mounting holes in t ank as shown.Secure ends of tank strut s (16) to tank as shown. Repeat for opposite side. Secure tank strut s (16) to pole as shown. Nut should be tightened until flush (even) with lock nuts outer edge.
14 P/N M601111 08/05 5. 6. Insert axle (5) through wheel bracket (4). Secure wheels (6) to axle using pushnuts (7). Carefully tap pushnut s onto axle with hammer or mallet 4 6 6 7 7 5 Install wheel assembly to base (8) using bolt s(9), washers(10) and nuts (1 1) as shown.
08/05 P/N M601111 15 TOOLS REQUIRED FOR THIS SECTION SECTION C: ASSEMBLE THE ELEV A TOR & BACKBOARD This is what your system will look like when you’ve finished this section: 9/16” 1/2” 3/8.
16 P/N M601111 08/05 1 . Install pole mount bracket (28) and reinforcement bracket (18) with carriage bolt s (22) as shown. T ighten flange nuts (1 1) completely . 1 28 11 11 18 22 22 2. Attach sp acers (24, 43) to pole mount bracket (28) with bolts (29), washers (50), and lock nuts (31) as shown.
08/05 P/N M601111 17 3 . 28 11 27 35 35 26 19 FIG . A Apply logo and height indicator labels (23) to adjustment rod (58) as shown. Attach handle part s (59, 60) to adjustment rod with screw (55), carriage bolt s (54), and flange nut s (1 1) as shown. 4 .
18 P/N M601111 08/05 29 30 30 29 52 Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (27). 27 5 . 6. 52 Assemble backboard brackets (52) using bolts (29), and nut s (30) as shown.
08/05 P/N M601111 19 46 46 47 44 46 46 47 48 Secure left (44) and right (45) p ad sections to board by pushing pads over the corners of the board. Secure completely by using screws (46) and washers (47) as shown. 7. 45 BOARD STYLE MA Y VA R Y Assemble board pad to board.
20 P/N M601111 08/05 8. 57 36 56 52 21 Attach lower elevator tubes (34) and counter balance spring (36) to backboard support brackets (52) using sp acers (53 & 56), bolt (57), and nut (21) as shown.
08/05 P/N M601111 21 9. Attach upper elevator tubes (33) to backboard support bracket s (52) using spacers (53), bolt (57), and nut (21) as shown. Tighten ALL Hardware from Step s 6-8 Af ter this Assembly is Completed.
22 P/N M601111 08/05 21 21 49 25 34 1 32 32 57 20 34 20 10. Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (25). 57 34 33 20 21 1 21 33 20 32 58 11 . Inst all upper elevator tubes (33) to triangle plates (63) as shown.
08/05 P/N M601111 23 12. Inst all Rim to Backboard A. Fit rim (67) securely into bracket (61) as shown. Allow T -bolt (66) to slip through center hole in rim (67). B. Install reinforcement bracket (62) onto T -bolt (66) as shown. C. Install spring (64) onto T -bolt (66) as shown.
24 P/N M601111 08/05 33 36 21 33 58 14. Insert bolt (57) through left side upper elevator tube (33), then stretch spring (36) onto bolt (57). Insert bolt (57) through right side upper elevator tube (33) and secure with nut (21). 57 36 Peel protective film from surface of acrylic backboard prior to use.
08/05 P/N M601111 25 1. Roll assembly to desired playing area. Fill base (8) with water (approx. 40 gallons) and snap base plugs (37) in place. 37 37 8 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
26 P/N M601111 08/05 1. Install front cover (38) by lining up st and-offs along the t ank struts. Insert a tie strap (39) through the top two and bottom two stand of fs. W rap tie straps around tank strut s as shown and secure tightly . T rim excess of tie strap as shown in FIG .
08/05 P/N M601111 27 1. Install cover (40) over spring return mechanism with screws (41) as shown. Place NBA label (51) on front of rim cover (40). 40 41 41 51 TOOLS REQUIRED FOR THIS SECTION Phillip .
28 P/N M601111 08/05 2. A. While holding handle, remove pin (27). B. Move elevator up or down to desired height. C. Replace pin (27) full length to lock system at desired height. 27 A. B. C. 58 DO NOT ALLOW CHILDREN TO ADJUST HEIGHT . W ARNING! 42 1. Apply Height Adjustment and Moving Label (42) to front of pole, where it is clearly visible.
Een belangrijk punt na aankoop van elk apparaat Spalding M60 1111 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Spalding M60 1111 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Spalding M60 1111 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Spalding M60 1111 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Spalding M60 1111 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Spalding M60 1111 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Spalding M60 1111 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Spalding M60 1111 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
