Gebruiksaanwijzing /service van het product M682001 van de fabrikant Spalding
Ga naar pagina of 23
1 12/06 ID# M682001 © COPYRIGHT 2006 by SPALDING Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-632 792 Internet Address: www.huffysports.
2 ID# M682001 12/06 BEFORE YOU ST ART T o ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. T est-fit large bolt s into large holes of elevator tubes, backboard brackets, and triangle plates.
12/06 ID# M682001 3 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system.
4 ID# M682001 12/06 Get to know the basic parts of your basketball system... TOP POLE MIDDLE POLE BOTTOM POLE STRUTS ELEVATOR ASSEMBLY BACKBOARD BASE WHEEL CARRIAGE ASSEMBLY FRONT BACK RIM.
12/06 ID# M682001 5 Item Qty. Part No. Description 1 1 600053 Tank 2 2 908556 Strut, Pole to Base 3 1 904501 Handle Assembly 4 1 FR908356 Top Pole Section 5 1 FR908357 Middle Pole Section 6 1 FR908360 Bottom Pole Section 7 2 800332 Wheel Bracket 8 2 600056 Wheel, 3.
6 ID# M682001 12/06 #16 (2) #12 (1) #45 (1) #39 (2) #23 (4) #26 (4) HARDW ARE IDENTIFIER (BOL TS & SCREWS) #20 (1) #25 (2) #51 (2) #18 (6) HARDW ARE IDENTIFIER (NUTS & W ASHERS) #14 (12) #10 (.
12/06 ID# M682001 7 #44 (1) #46 (1) #47 (1) #13 (2) #30 (4) #49 (1) #50 (8) HARDW ARE IDENTIFIER (PLASTIC SP ACERS CAPS & CLIPS) HARDW ARE IDENTIFIER (OTHER) * You may have extra parts with this model.
8 ID# M682001 12/06 7 8 8 9 13 13 Complete wheel assembly as shown in Figure A. Secure wheel bracket (7) and wheel assembly (Fig. A.) to the tank (1) with a bolt s (18) and washers (24). 24 TO INSTALL SECOND PUSHNUT: • Assemble Pushnut, Wheels, Axle, And Wheel Bracket As Shown.
12/06 ID# M682001 9 Correctly identify each pole section. Poles have an identification sticker that will be used as a reference point in the next step. 2. Bounce middle pole section (5) into top section (4) using a wood scrap as shown until the top pole no longer moves toward the pole identification sticker on the middle pole.
10 ID# M682001 12/06 4. Bounce top and middle pole assembly (4 and 5) onto bottom pole section (6) using a wood scrap as shown. Bounce until the top and middle pole assembly no longer moves toward the pole identification mark on the bottom pole.
12/06 ID# M682001 11 6. Secure tank strut s (2) through center hole in pole as shown. 12 10 2 2 TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. W ARNING! IMPORT ANT! DO NOT TIGHTEN COMPLETEL Y .
12 ID# M682001 12/06 8. 42 6 14 16 15 IMPORT ANT! DO NOT OVER TIGHTEN! 7. 2 2 18 24 24 2 2 18 IMPORT ANT! DO NOT TIGHTEN COMPLETEL Y . TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
12/06 ID# M682001 13 Securely rest the assembly on sawhorse. Identify elevator tubes (32 and 35). 35 32 9. Toward Pole Toward Board 4 35 51 50 40 49 29 29 40 50 COMPLETED ASSEMBL Y 31 32 TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
14 ID# M682001 12/06 While still supported on sawhorse. Attach elevator tubes (32, 35) to backboard using sp acers (30), bolts (23), and nut s (31) as shown.
12/06 ID# M682001 15 2. 45 Insert T -bolt (45) into Slam Jam bracket (44) then, attach that assembly to board using bolts (26) and nut s (14). 14 26 27 IMPORT ANT! Carefully cut and peel protective film away from board prior to att aching rim.
16 ID# M682001 12/06 3. 29 31 36 35 35 W ARNING! USE EYE PROTECTION WHEN INST ALLING SPRINGS. 35 35 Support pole on sawhorse. Attach counter balance spring (36) to the spring support bracket (27) using bolt (51) and nut (31) as shown. Insert bolt (29) through left side upper elevator tube (35), then stretch spring (36) onto bolt (29).
12/06 ID# M682001 17 Inst all Slam Jam Rim to Backboard A. Fit rim (34) securely into bracket (44) as shown. Allow T -bolt (45) to slip through center hole in rim (34). B. Install reinforcement bracket (46) onto T -bolt (45) as shown. C. Install spring (47) onto T -bolt (45) as shown.
18 ID# M682001 12/06 Slide upper tube (17) onto handle assembly (3). Reinsert screws removed in previous step as shown. 5. 6. Remove packaging materials from handle assemblies (17 and 3). Remove screws on both sides of tube. 17 3 17 Screws r emoved in step 6 3 Rotate upper tube to line up screw holes.
12/06 ID# M682001 19 Install handle assembly (17) to lower elevator tubes (32) using bolt (29), spacers (50), and nut (31) as shown. Secure the handle assembly (3 & 17) to pole bracket (15) using bolt (20) and nut (10) as shown. 8. Secure the front panel (21) to struts (2) as shown with carriage bolts (22) and nuts (14).
20 ID# M682001 12/06 10. Roll completed assembly to desired position. Fill tank with water (approx. 40 gallons (128 Liters)) or sand (approx. 475 lbs. (216 kg)) and rotate the cap (41) into base (1). TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COU LD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
12/06 ID# M682001 21 Apply Height Adjustment and Moving Label (33) to front of pole, where it is clearly visible. 11 . 12. B. D. C. A. Install net (43). 34 39 28 Cover plate (28) will fit INSIDE back bracket. NOTE: 43 34 43 34 13. RIM COVER A TT ACHMENT 39 566 2 00 12 /05 H EI G H T A D JUS TMENT TO ADJUST BACKBOARD: 1.
22 ID# M682001 12/06 SECTION C: BOARD P AD Item Qty . Part No . Description 1 1 20157801 Board Pad, Left Section 2 1 20157901 Board Pad, Right Section 3 1 201580 Board Pad, Center Section 4 4 206081 Screw , Self Drilling, Hex Washer Head, 1/4 x .
12/06 ID# M682001 23 Using a portable drill (with adjust able torque) and a 5/16 socket and extension drill through the backboard frame and secure the pads in place with self-tapping screws provided. Use screws (7) for center pad and screws (4) for outer p ads It may be necessary to use an 1 1/16 drill bit (6) to pre-drill on some backboards (FIG .
Een belangrijk punt na aankoop van elk apparaat Spalding M682001 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Spalding M682001 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Spalding M682001 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Spalding M682001 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Spalding M682001 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Spalding M682001 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Spalding M682001 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Spalding M682001 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
