Gebruiksaanwijzing /service van het product MIGHTYLAM 2700 van de fabrikant Banner American Products
Ga naar pagina of 22
OPERATING INSTRUCTIONS MIGHTYLAM 2700 ROLL LAMINATOR.
2 TABLE OF CONTENTS Safety Messages and Electrical Safeguards ..................... .........3 - 4 Introduction ........................ ..................... ..................... .................... Laminator Features . ............................
3 IMPORTANT SAFETY MESSAGES AND ELECTRICAL SAFEGUARDS For your protection, do not connect the laminator to electrical power or attempt to operate it until you read these instructions completely. Keep these instructions in a convenient location for future reference.
4 If the below conditions exist do not attempt to service or repair the laminator yourself. Unplug the laminator from the electrical outlet and contact an authorized service representative. • When the power supply cord or plug is damaged or frayed.
5 INTRODUCTION Congratulations on your purchase of the MightyLam 2700 Roll Laminator. This unit is designed to provide years of trouble-free service. The MightyLam 2700 will accept rolls of laminating film up to 27” wide in all film thicknesses. Paper and card stock up to 1/16” (1.
6 INITIAL SETUP Unpacking... Before unpacking the unit, inspect the shipping container for signs of damage. Notify the carrier and your dealer immediately if any damage is noted. Components... Figure 1 below shows the location of the major components and controls of the MightyLam 2700.
7 OPERATING INSTRUCTIONS Heat Control Your new MightyLam 2700 has digital heat controllers for each heat shoe. Users can easily adjust the set temperature for each heat shoe individually to achieve the best quality lamination. Both controllers have been calibrated to accurately display the heat shoe temperature in the laminating range.
8 OPERATION This section describes the operation of your MightyLam 2700. This laminator is designed for all widths of plastic up to 27”. However, if narrower widths are used the Heat Shoes must be cleaned before using a wider roll. Refer to the MAINTENANCE section for cleaning instructions.
9 4. Pull 6”-12” of film from the bottom roll. Pass it under the lower idler bar. You can “d rop-down” the lower idler bar to give you more clearance. After doing so, return the idler bar to its upper position for running the machine. Drape the film from the bottom roll over the film from the top roll.
10 Adjusting Mandrel/Film Tension….. Each type of laminating film has different characteristics a nd may require laminator adjustment. The tensi on should be set so that the film moves over the heat shoes without wrinkles as the film enters the laminator.
11 Caution! If the blade release knobs are turned too far, the slitter blade may fall out of its guide and come in contact with the rubber rollers. If this happens, the rollers could be damaged. Never turn the blade release knobs m ore than one turn to position the blades.
12 Note : You may want to run a test lamination first as any item that passes between the heat shoes will be laminated and cannot be recovered un til it exits the rear of the laminator. 5. Additional items may be fed in sequence, k eeping enough distance between sheets for trimming.
13 Mounting your print: 1. Be sure all laminator parts (i.e. safety shield, feed tabl e, etc.) are in their proper positions and the lam inating film is loaded correctly on top and bottom m andrels.
14 TROUBLESHOOTING PROBLEM: Laminator is inoperative. Moto r does not run, indicator lights are out. ACTION: Unit may be unplugged. Connect power suppl y. Ensure that your circuit breaker has not tripped. Fuse m ay have blown. Replace 15 amp power fuse.
15 MAINTENANCE This section contains instructions for cleaning and mainta ining your lam inator. These procedures should be preformed at regular intervals to help ensure the trouble-free operation of your lam inator. Cleaning the Heat Shoes and Laminating Rollers.
16 WARRANTY AND RETURN POLICY Warranty Your laminator is warranted to be free of def ects in material and workmanship for a period of 1 year from the original purchase date. In the ev ent of a defect in material or workmanship, the manufacturer or its authorized dealer, will repair or replace (at their option) the laminator.
17 PARTS LIST AND ILLUSTRATIONS This section contains refere nce d rawings and a par tial parts list to assist you wh e n ordering parts for your laminator.
18 43 10103 TABLE, FEED 1 44 11539 SUPPORT, RIGHT SIDE 1 45 11538 SUPPORT, LEFT SIDE 1 46 503 SPACER WASHER 8 47 1319 LIGHT,INDICATOR,RED 120V 1 48 11095 SWITCH, RED (HEAT) 1 49 11094 SWITCH, GREEN (M.
19.
20.
21.
22.
Een belangrijk punt na aankoop van elk apparaat Banner American Products MIGHTYLAM 2700 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Banner American Products MIGHTYLAM 2700 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Banner American Products MIGHTYLAM 2700 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Banner American Products MIGHTYLAM 2700 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Banner American Products MIGHTYLAM 2700 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Banner American Products MIGHTYLAM 2700 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Banner American Products MIGHTYLAM 2700 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Banner American Products MIGHTYLAM 2700 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
