Gebruiksaanwijzing /service van het product CR27 van de fabrikant Stanley Black & Decker
Ga naar pagina of 24
© 201 1 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 30673 6/2012 V er . 6 S afety , O pera tiOn and M aintenance USer ManUaL CR27 HYDRAULIC CIRCULAR SA W.
.
CR27 User Manual ◄ 3 T ABLE OF CONTENTS SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an au - thorized and certied dealer .
4 ► CR27 User Manual SAFETY SYMBOLS Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
CR27 User Manual ◄ 5 SAFETY PRECAUTIONS T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety .
6 ► CR27 User Manual SAFETY PRECAUTIONS • Ensure that the direction of rotation of the saw blade is as prescribed in this manual. • Cut at the rated operating speeds (gpm). • Operate the saw at “no load” for 30 seconds in a safe position and ensure there is no excessive vi- bration or other defects detected.
CR27 User Manual ◄ 7 ELECTRICAL HAZARDS When a lifting device contacts an electrical conductor , the truck supporting the device is considered to be ener- gized and contact with the truck must be avoided except when emergency rescue procedures are being carried out.
ELECTRICAL HAZARDS 8 ► CR27 User Manual T able 1. Minimum approach distances from energized conductors for qualied line-clearance arborists and qualied line-clearance arborist trainees. Nominal V oltage kV phase-to-phase Includes 1910.269 elevation factor , sea level to 5000 ft 1 ) Includes 1910.
ELECTRICAL HAZARDS CR27 User Manual ◄ 9 The tie-in position should be above the work area and located in such a way that a slip would swing the arborist away from any energized electrical conductors or other identied hazard.
10 ► CR27 User Manual T OOL STICKERS & T AGS Fa ilure to use hydraulic hose labeled and certified as non-conductive when using hydraulic tool so n or near electric lines ma yr esul ti n deat ho .
CR27 User Manual ◄ 1 1 HOSE TYPES The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
12 ► CR27 User Manual HOSE RECOMMENDA TIONS Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber.
CR27 User Manual ◄ 13 HTMA REQUIREMENTS Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min.
14 ► CR27 User Manual OPERA TION PREOPERA TION PROCEDURES PREP ARA TION FOR INITIAL USE Each unit as shipped has no special unpacking or as- sembly requirements prior to usage. Inspection to as- sure the unit was not damaged in shipping and does not contain packing debris is all that is required.
CR27 User Manual ◄ 15 OPERA TION 13 OPERA TION BLADE INST ALLA TION 1. Handle the saw blade with care. The cutting edges are sharp and careless handling could result in injury .
16 ► CR27 User Manual OPERA TION 4. In sawing limbs which have a tendency to split or tear when making a single saw ush cut, Figure 4, it is advisable to make more than one cut. The rst cut is made a few inches from the point of the ush cut removing the weight of the limb being trimmed out and leaving a short stub.
CR27 User Manual ◄ 17 OPERA TION AFTER OPERA TION 1. Wipe the saw thoroughly with a clean dry or slightly oiled cloth. 2. Clean tree pitch and residue from the blade. Handle the blade with care to avoid getting cut by the sharp teeth. 3. Check all fasteners for tightness.
18 ► CR27 User Manual OPERA TION Figure 8. Setting Cutter T ooth Angle COLD WEA THER OPERA TION If the saw is to be used during cold weather , preheat the hydraulic uid at low engine speed. When using the normally recommended uids, uid temperature should be at or above 50 °F/10 °C (400 ssu/82 centistokes) be- fore use.
CR27 User Manual ◄ 19 T OOL PROTECTION & CARE • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy- draulic system.
20 ► CR27 User Manual TROUBLESHOOTING If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the saw , always make sure the hydraulic power source is supplying the correct hydraulic ow and pressure to the saw as listed in the table.
CR27 User Manual ◄ 21 SPECIFICA TIONS Capacity............................................................................................................................9 in. Diameter/23 cm Blade Pressure Range .....................................
22 ► CR27 User Manual CR27 P ARTS ILLUSTRA TION.
CR27 User Manual ◄ 23 CR27 P ARTS LIST ITEM P ART NO. QTY DESCRIPTION 1 00042 2 OIL TUBE ASSY 2 24829 1 OUTER TUBE ASSY 3 18089 6 CAPSCREW , BUTTONHEAD, 1/4-20 × 3/8 4 00227 1 FIXED COLLAR 5 00103 .
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulic.com IMPORT ANT T o ll out a Product Warranty Recording form, and for information on your warranty , visit Stanleyhydraulic.
Een belangrijk punt na aankoop van elk apparaat Stanley Black & Decker CR27 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Stanley Black & Decker CR27 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Stanley Black & Decker CR27 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Stanley Black & Decker CR27 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Stanley Black & Decker CR27 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Stanley Black & Decker CR27 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Stanley Black & Decker CR27 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Stanley Black & Decker CR27 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
