Gebruiksaanwijzing /service van het product HD01 van de fabrikant Stanley Black & Decker
Ga naar pagina of 20
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 72659 2/2015 V er . 6 USER MANUAL Safety , Operation and Maintenance HD01 Hydraulic Hammer Drill.
2 ► HD01 User Manual DECLARATION OF CONF ORM ITY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONF ORMITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFO RMITA Hydraulic Tools _______ ______.
HD01 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer .
4 ► HD01 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
HD01 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs.
6 ► HD01 User Manual SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
HD01 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
8 ► HD01 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
HD01 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max.
10 ► HD01 User Manual PRE-OPERA TION PROCEDURES CHECK POWER SOURCE 1. Using a calibrated owmeter and pressure gauge, check that the hydraulic power source develops a ow of 4–9 gpm/15–34 lpm at 950–2000 psi/65–140 bar .
HD01 User Manual ◄ 1 1 MODE SELECTOR (FIG 2) Drill only mode: T o use drill-only mode, press mode selector button (B) g-2 and turn the mode selec - tor (A) so the yellow arrow points to the corresponding symbol. Use drill-only mode for screwdriving and for drilling into metal, wood and plastics.
12 ► HD01 User Manual SIDE HANDLE The side handle assembly , including the depth gauge, ts over the front housing of the hammer drill to assist the operator in maneuvering the tool. T o adjust the side handle to a comfortable position, twist the hand grip in a counterclockwise direction and reposi- tion the handle assembly .
HD01 User Manual ◄ 13 T ighten further by applying the chuck key successively to all three guide holes of the chuck. The chuck key must not be attached to the tool with a chain, cord, or similar means.
14 ► HD01 User Manual This tool is furnished with an on-off valve spool commonly referred to as a “dual spool” which permits adjustment so the tool may be operated on either an open-center hydraulic system or a closed-center hydraulic system. The dual spool is normally set to the open-center (OC) position at time of manufac- ture.
HD01 User Manual ◄ 15 PROBLEM CAUSE SOLUTION Drill will not start Power not being supplied. Check to make certain that both hoses are connected. T urn hydraulic circuit control valve ON. Defective quick-disconnect. Check each disconnect separately .
16 ► HD01 User Manual PROBLEM CAUSE SOLUTION Drill operates in only one direction. Forward or reverse. Reverse spool incorrectly installed. Do not separate modules. Reassemble. See Service section. Reverse spool faulty . Do not separate modules. Replace reverse spool.
HD01 User Manual ◄ 17 Rotation Speed at 6 gpm ................................................................................................................................ 800 rpm Blows per Minute at 6 gpm ........................................
18 ► HD01 User Manual 1 2 3 4 5 6 8 9 10 11 12 13 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 43 45 47 48 50 51 52 53 56 57 58 60 62 64 65 6 19 14 46 16 16 42 61.
HD01 User Manual ◄ 19 ITEM P/N QTY DESCRIPTION 1 00106 1 * O-RING 3/8 X 1/2 X 1/16 -012 2 001 12 1 * QUAD RING 1/4 X 3/8 X 1/16 -010 3 00179 1 MOT OR SEAL W ASHER 4 00289 2 DOWEL PIN 3/16 X 3/4 LG. 5 00621 1 * O-RING 1-1/4 X 1-3/8 X 1/16 -026 6 00779 7 HSHCS 8-32 X 1.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
Een belangrijk punt na aankoop van elk apparaat Stanley Black & Decker HD01 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Stanley Black & Decker HD01 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Stanley Black & Decker HD01 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Stanley Black & Decker HD01 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Stanley Black & Decker HD01 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Stanley Black & Decker HD01 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Stanley Black & Decker HD01 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Stanley Black & Decker HD01 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
