Gebruiksaanwijzing /service van het product H8DII+-F van de fabrikant SUPER MICRO Computer
Ga naar pagina of 78
® S UPER H8DI3+-F H8DI3+ H8DII+-F H8DII+ USER’S MANUAL Revision 1.0c.
The information in this User ’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates.
Preface iii Preface About This Manual This manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the H8DI3+/I+(-F) Serverboard.
Manual Organization Chapter 1 includes a checklist of what should be included in your serverboard box, describes the features, speci fi cations and performance of the serverboard and provides detailed information about the chipset. Chapter 2 begins with instructions on handling static-sensitive devices.
H8DI3+/I+(-F) Serverboard User ’ s Manual v T able of Contents Chapter 1 Introduction 1-1 Overview ............................................................................................................ 1 Checklist .............................
vi T able of Contents Serial Ports .................................................................................................. 10 SGPIO .......................................................................................................... 1 1 SMBus Header .
H8DI3+/I+(-F) Serverboard User ’ s Manual vii Enabling SA T A RAID in the BIOS ............................................................... 20 Using the Adaptec RAID Utility ........................................................................
viii Notes Preface.
Chapter 1: Introduction 1-1 Chapter 1 Introduction 1-1 Overview Checklist Congratulations on purchasing your computer serverboard from an acknowledged leader in the industry . Supermicro boards are designed with the utmost attention to detail to provide you with the highest standards in quality and performance.
1-2 H8DI3+/I+(-F) Serverboard User ’ s Manual 1-2 Contacting Supermicro Headquarters Address: Super Micro Computer , Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. T el: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.
Chapter 1: Introduction 1-3 Figure 1-1. H8DI3+/I+(-F) Serverboard Image.
1-4 H8DI3+/I+(-F) Serverboard User ’ s Manual Notes: Jumpers not indicated are for test purposes only . Not all ports, jumpers or LED Indicators are available on all serverboards.
Chapter 1: Introduction 1-5 H8DI3+/I+(-F) Serverboard Quick Reference Jumper Description Default Setting JBT1 CMOS Clear (See Section 2-7) JCF1 Compact Flash Master/Slave Closed (Master) JI 2 C1/JI 2 .
1-6 H8DI3+/I+(-F) Serverboard User ’ s Manual Connector Description COM1/COM2 COM1 Serial Port/Header F AN 1-8 Chassis/CPU Fan Headers Floppy Floppy Disk Drive Connector I-Button I-Button Socket (fo.
Chapter 1: Introduction 1-7 Serverboard Features CPU Dual AMD Opteron 2000 series (Socket F type) processors • Note: Supports 237x, 238x, 235x and 24xx processors.
1-8 H8DI3+/I+(-F) Serverboard User ’ s Manual ACPI Features Microsoft OnNow • Slow blinking LED for suspend state indicator • BIOS support for USB keyboard • W ake-On-LAN (WOL) and W ake-On-Ri.
Chapter 1: Introduction 1-9 Figure 1-3. AMD SR5690/SP5100 Chipset: System Block Diagram Note: This is a general block diagram and may not exactly represent the features on your serverboard. See the previous pages for the actual speci fi cations of your serverboard.
1-10 H8DI3+/I+(-F) Serverboard User ’ s Manual 1-3 Chipset Overview The H8DI3+/I+(-F) Serverboard serverboard is based on the AMD SR5690/SP5100 chipset. This chipset functions as a Media and Communications Processor (MCP). Controllers for the system memory are integrated directly into AMD Opteron processors.
Chapter 1: Introduction 1-1 1 CPU Overheat/Fan Fail LED and Control This feature is available when the user enables the CPU overheat/Fan Fail warning function in the BIOS. This allows the user to de fi ne an overheat temperature. When this temperature is exceeded or when a fan failure occurs, the Overheat/Fan Fail warning LED is triggered.
1-12 H8DI3+/I+(-F) Serverboard User ’ s Manual W ake-On-LAN (WOL) W ake-On-LAN is de fi ned as the ability of a management application to remotely power up a computer that is powered off.
Chapter 1: Introduction 1-13 1-7 Super I/O The disk drive adapter functions of the Super I/O Winbond ® 83627DHG chip include a fl oppy disk drive controller that is compatible with industry standard.
1-14 H8DI3+/I+(-F) Serverboard User ’ s Manual Notes.
Chapter 2: Installation 2-1 Chapter 2 Installation 2-1 Static-Sensitive Devices Electrostatic Discharge (ESD) can damage electronic com ponents. T o prevent damage to your system board, it is important to handle it very carefully . The following measures are generally suf fi cient to protect your equipment from ESD.
H8DI3+/I+(-F) Serverboard User's Manual 2-2 ! 2-2 Processor and Heatsink Installation Exercise extreme caution when handling and installing the processor . Always connect the power cord last and always remove it before adding, removing or changing any hardware components.
Chapter 2: Installation 2-3 Installing the Heatsinks We recommend the use of active type heatsinks (except for 1U systems). Use any onboard fan header for the CPU's heatsink fan. T o install the heatsink, please follow the installation instructions included with your heatsink package (not included).
H8DI3+/I+(-F) Serverboard User's Manual 2-4 2-3 Mounting the Serverboard into a Chassis All motherboards have standard mounting holes to fi t different types of chassis. Make sure that the locations of all the mounting holes for both the serverboard and the chassis match.
Chapter 2: Installation 2-5 Gently press down on the memory module until it snaps into place. 3. With two CPUs installed, repeat step 2 to populate the CPU2 DIMM slots. 4. Always install pairs of DIMMs to both CPU DIMM slots for more ef fi cient operation.
H8DI3+/I+(-F) Serverboard User's Manual 2-6 2-5 PCI Expansion Cards A riser card is used to support one standard size (full height full length) PCI expansion card. Installing a PCI Expansion Card Con fi rm that you have the correct riser card for your chassis model and the 1.
Chapter 2: Installation 2-7 2-6 I/O Port and Control Panel Connections The I/O ports are color coded in conformance with the PC99 speci fi cation to make setting up your system easier . See Figure 2-2 below for the colors and locations of the various I/O ports.
H8DI3+/I+(-F) Serverboard User's Manual 2-8 2-7 Connector De fi nitions Power Connectors A 24-pin main power supply connector(JPW1) and two 8-pin CPU PWR connectors (JPW2/JPW3) on the serverboard. These power connectors meet the SSI EPS 12V speci fi cation.
Chapter 2: Installation 2-9 NIC2 (LAN2) LED The LED connections for LAN2 are on pins 9 and 10 of JF1. Attach LAN LED cables to display network activity . See the table on the right for pin de fi nitions. HDD LED The HDD LED connection is located on pins 13 and 14 of JF1.
H8DI3+/I+(-F) Serverboard User's Manual 2-10 Universal Serial Bus Ports T wo Universal Serial Bus ports (USB 2.0) are located beside the Keyboard and Mouse PS2 ports. T wo additional T ype A ports (USB4/5) are included on the serverboard near the PCI Slot 1.
Chapter 2: Installation 2-1 1 Overheat LED Connect an LED to the JOH1 header to provide warning of chassis overheating. See the table on the right for pin de fi nitions. Overheat LED Pin De fi nitions (JOH1) Pin# De fi nition 1 3.3V 2 OH Active W ake-On-LAN The W ake-On-LAN header is designated JWOL.
H8DI3+/I+(-F) Serverboard User's Manual 2-12 Chassis Intrusion A Chassis Intrusion header is located at JL1. Attach the appropriate cable to inform you of a chassis intrusion.
Chapter 2: Installation 2-13 Compact Flash Card PWR Connector A Compact Flash Card Power Connector is located at JWF1. For the Compact Flash Card to work properly , you will need to enable it with the JCF1 jumper and connect a Compact Flash Card power cable to JWF1 fi rst.
H8DI3+/I+(-F) Serverboard User's Manual 2-14 VGA Enable/Disable JPG1 allows you to enable or disable the VGA port. The default position is on pins 1 and 2 to enable VGA.
Chapter 2: Installation 2-15 LAN1/2 Enable/Disable Change the setting of jumper JPL1 and JPL2 to enable or disable the LAN1 and LAN2 Ethernets ports, respectively .
H8DI3+/I+(-F) Serverboard User's Manual 2-16 2-9 Onboard Indicators LAN1/LAN2 LEDs The Ethernet ports (located beside the VGA port) have two LEDs. On each Gb LAN port, one LED blinks to indicate activity while the other may be green, amber or off to indicate the speed of the connection.
Chapter 2: Installation 2-17 2-10 Floppy , SAS and SA T A Drive Connections Use the following information to connect the IDE hard disk drive cables. A red mark on a wire typically designates the location of pin 1. • The 80-wire A T A100/66 IDE hard disk drive cable that came with your system • has two connectors to support two drives.
H8DI3+/I+(-F) Serverboard User's Manual 2-18 SA T A Ports There are no jumpers to con fi gure the SA T A ports, which are designated SA T A0 through SA T A5.
Chapter 2: Installation 2-19 2-1 1 Enabling SA T A RAID Now that the hardware is set up, you must install the operating system and the SA T A RAID drivers, if you wish to use RAID with your SA T A drives.
H8DI3+/I+(-F) Serverboard User's Manual 2-20 Enabling SA T A RAID in the BIOS Before installing the Windows Operating System, you must change some settings in BIOS. Boot up the system and hit the <Del> key to enter the BIOS Setup Utlility .
Chapter 2: Installation 2-21 Figure 2-5. Adaptec RAID Utility Program Screen Using the Adaptec RAID Utility The Adaptec® RAID Utility program is where you can de fi ne the drives you want to include in the RAID array and the mode and type of RAID.
H8DI3+/I+(-F) Serverboard User's Manual 2-22 Figure 2-6. Driver/T ool Installation Display Screen 2-12 Installing Drivers The CD that came bundled with the system contains drivers, some of which must be installed, such as the chipset driver . After inserting this CD into your CD-ROM drive, the display shown in Figure 2-6 should appear .
Chapter 2: Installation 2-23 Supero Doctor III The Supero Doctor III program is a Web base management tool that supports remote management capability .
H8DI3+/I+(-F) Serverboard User's Manual 2-24 Note: Super Doctor III Software Revision 1.0 can be downloaded from our Web Site at: ftp://ftp.supermicro.com/utility/Supero_Doctor_III/. Y ou can also download the Super Doctor III User's Guide at: <http://www .
3-1 Chapter 3: T roubleshooting Chapter 3 T roubleshooting 3-1 T roubleshooting Procedures Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the ‘T echnical Support Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter .
3-2 H8DI3+/I+(-F) Serverboard User's Manual T urn the power switch on and off to test the system. 4. The battery on your serverboard may be old. Check to verify that it still 5. supplies ~3VDC. If it does not, replace it with a new one. No Video If the power is on but you have no video, remove all the add-on cards and 1.
3-3 Chapter 3: T roubleshooting 3-2 T echnical Support Procedures Before contacting T echnical Support, please take the following steps. Also, note that as a serverboard manufacturer , we do not sell directly to end-users, so it is best to fi rst check with your distributor or reseller for troubleshooting services.
3-4 H8DI3+/I+(-F) Serverboard User's Manual Select your serverboard model on the web page and download the corresponding BIOS fi le to your computer . Unzip the BIOS update fi le, in which you will fi nd the readme.txt ( fl ash instructions), the afudos.
Chapter 4: BIOS 4-1 Chapter 4 BIOS 4-1 Introduction This chapter describes the AMIBIOS™ Setup utility for the H8DI3+/I+(-F) Serverboard. The AMI ROM BIOS is stored in a fl ash chip and can be easily upgraded using a fl oppy disk-based program.
4-2 H8DI3+/I+(-F) Serverboard User ’ s Manual 4-2 Main Menu When you fi rst enter AMI BIOS Setup Utility , you will see the Main Menu screen. Y ou can always return to the Main Menu by selecting the Main tab on the top of the screen with the arrow keys.
Chapter 4: BIOS 4-3 W ait for F1 if Error This setting controls the system response when an error is detected during the boot sequence. When enabled, BIOS will stop the boot sequence when an error is detected, at which point you will need to press the F1 button to re-enter the BIOS setup menu.
4-4 H8DI3+/I+(-F) Serverboard User ’ s Manual Secure Virtual Machine Mode This setting is used to Enable or Disable SVM. Power Now This setting is used to Enable or Disable the AMD Power Now feature for generating ACPI _PPC, _PSS and _PCT objects.
Chapter 4: BIOS 4-5 Channel Interleaving Selects the channel-interleaving memory scheme when this function is supported by the processor . The options are Disabled, Address Bits 6, Address Bits 12, XOR of Address Bits [20:16, 6] and XOR of Address Bits [20:16, 9].
4-6 H8DI3+/I+(-F) Serverboard User ’ s Manual DRAM ECC Enable This setting allows hardware to report and correct memory errors automatically , maintaining system integrity .
Chapter 4: BIOS 4-7 DRAM Timing Con fi guration Memory Clock Mode This setting speci fi es the memory clock mode. Options are Auto , Limit and Manual. DRAM Timing Mode This setting speci fi es the DRAM timing mode. Options include Auto , DCT 0, DCT 1 and Both.
4-8 H8DI3+/I+(-F) Serverboard User ’ s Manual RD890 Con fi guration PCI Express Con fi guration Port Features This submenu allows you to set the features for Ports 02 through 13 in the system. Each port submenu allows you to de fi ne the same settings below .
Chapter 4: BIOS 4-9 Hot Plug Support Use this setting to set Hot Plug Support. Options include Disabled and Native. NB-SB Port Features NB-SB Link APSM Use this to set the NB-SB Link ABSM. Options include L1 and Dis- abled. Link Width This setting allows you to set the Link Width for the NB-SB port.
4-10 H8DI3+/I+(-F) Serverboard User ’ s Manual TX Drive Strength Use this setting to con fi gure TX drive strength. Options include Auto , 26mA, 20mA, 22mA and 24mA. TXCLK Clock Gating in L1 Use this setting to Enable or Disable the TXCLK clock gating in L1.
Chapter 4: BIOS 4-1 1 HT Link T ristate This setting allwos you to con fi gure the HT Link T ristate. Options include Auto , Disabled, CAD/CTL and CAD/CTL/CLK. NB Deemphasis Level Use this to set the NB deemphasis level. Options include Disabled, 0.4 dB, 1.
4-12 H8DI3+/I+(-F) Serverboard User ’ s Manual Block (Multi-Sector T ransfer) Block mode boosts IDE drive performance by increasing the amount of data transferred. Only 512 bytes of data can be transferred per interrupt if block mode is not used. Block mode allows transfers of up to 64 KB per interrupt.
Chapter 4: BIOS 4-13 IDE Detect Time Out (Sec) Use this to set the time out value for detecting A T A/A T API devices. Options are 0-35 seconds in 5 second increments. PCI/PnP Con fi guration Clear NVRAM Select Y es to clear NVRAM during boot-up.
4-14 H8DI3+/I+(-F) Serverboard User ’ s Manual Load Onboard LAN 2 Option ROM Use this setting to Enable or Disable the onboard LAN 2 option ROM. Load Onboard SAS Option ROM Use to setting to Enable or Disable SAS option ROM. Boots Graphic Adapter Priority Use this setting to specify the priority for the boot graphic adapter .
Chapter 4: BIOS 4-15 Remote Access Con fi guration Remote Access Allows you to Enable or Disable remote access. If enabled, the settings below will appear . Serial Port Number Selects the serial port to use for console redirection. Options are COM1, COM2 and COM3 .
4-16 H8DI3+/I+(-F) Serverboard User ’ s Manual Hardware Health Con fi guration CPU Overheat Alarm Use the "+" and "-" keys to set the CPU temperature threshold to between 65 o and 90 o C. When this threshold is exceeded, the overheat LED on the chassis will light up and an alarm will sound.
Chapter 4: BIOS 4-17 ACPI Aware O/S This setting enables or disables ACPI support for the Operating System. Options include Ye s for enable and No for disable. ACPI APIC Support Determines whether to include the ACPI APIC table pointer in the RSDT pointer list.
4-18 H8DI3+/I+(-F) Serverboard User ’ s Manual IP Address In the fi eld provided here enter the IP address in the decimal form of xxx.xxx. xxx.xxx with xxx having a value of less than 256 and in decimal form only . Subnet Mask In the fi eld provided here enter the Subnet address in the decimal form of xxx.
Chapter 4: BIOS 4-19 4-4 Security Menu AMI BIOS provides a Supervisor and a User password. If you use both passwords, the Supervisor password must be set fi rst. Change Supervisor Password Select this option and press <Enter> to access the sub menu, and then type in the password.
4-20 H8DI3+/I+(-F) Serverboard User ’ s Manual 4-6 Exit Menu Select the Exit tab from AMI BIOS Setup Utility screen to enter the Exit BIOS Setup screen.
Appendix A BIOS Error Beep Codes During the POST (Power-On Self-T est) routines, which are performed each time the system is powered on, errors may occur . Non-fatal errors are those which, in most cases, allow the system to continue the boot-up process.
A-2 H8DI3+/I+(-F) Serverboard User ’ s Manual Notes.
B-1 Appendix B: BIOS POST Checkpoint Codes Appendix B BIOS POST Checkpoint Codes When AMIBIOS performs the Power On Self T est, it writes checkpoint codes to I/O port 0080h. If the computer cannot complete the boot process, diagnostic equipment can be attached to the computer to read I/O port 0080h.
B-2 H8DI3+/I+(-F) Serverboard User ’ s Manual B-2 Bootblock Recovery Codes The bootblock recovery checkpoint codes are listed in order of execution: Checkpoint Code Description E0h The onboard fl oppy controller if available is initialized. Next, beginning the base 512 KB memory test.
B-3 Appendix B: BIOS POST Checkpoint Codes B-3 Uncompressed Initialization Codes The following runtime checkpoint codes are listed in order of execution. These codes are uncompressed in F0000h shadow RAM. Checkpoint Code Description 03h The NMI is disabled.
B-4 H8DI3+/I+(-F) Serverboard User ’ s Manual Checkpoint Code Description 2Eh Completed post-video ROM test processing. If the EGA/VGA controller is not found, performing the display memory read/write test next. 2Fh The EGA/VGA controller was not found.
B-5 Appendix B: BIOS POST Checkpoint Codes Checkpoint Code Description 54h Shutdown was successful. The CPU is in real mode. Disabling the Gate A20 line, parity , and the NMI next. 57h The A20 address line, parity , and the NMI are disabled. Adjusting the memory size depending on relocation and shadowing next.
B-6 H8DI3+/I+(-F) Serverboard User ’ s Manual Checkpoint Code Description 99h Any initialization required after the option ROM test has completed. Con fi guring the timer data area and printer base address next. 9Ah Set the timer and printer base addresses.
Een belangrijk punt na aankoop van elk apparaat SUPER MICRO Computer H8DII+-F (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen SUPER MICRO Computer H8DII+-F heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens SUPER MICRO Computer H8DII+-F vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding SUPER MICRO Computer H8DII+-F leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over SUPER MICRO Computer H8DII+-F krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van SUPER MICRO Computer H8DII+-F bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de SUPER MICRO Computer H8DII+-F kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met SUPER MICRO Computer H8DII+-F . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
