Gebruiksaanwijzing /service van het product TCS-3401 van de fabrikant Tanaka
Ga naar pagina of 20
Owner’ Owner’ Owner’ Owner’ Owner’ s Man s Man s Man s Man s Man ual ual ual ual ual Model Numbers: T T T T T CS-3401 CS-3401 CS-3401 CS-3401 CS-3401 CHAINSAW CHAINSAW CHAINSAW CHAINSAW CHAINSAW P/N 29356 Date 04-20-01 Supplier T o The Outdoor P ower Equipment Industry ISM, Inc .
www.tanakapowerequipment.com 1 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 Before using this unit: • Read the operator’s manual carefully. • Check that the cutting equipment is correctly assembled and adjusted. • Start the unit and check the carburetor adjustment.
www.tanakapowerequipment.com 2 custsvc@tanaka-ism.com Owner’s Manual TCS-3401.
www.tanakapowerequipment.com 3 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 2. Warnings and safety instructions Operator Safety WARNING! This chain saw is designed especially for tree care and surgery. Only persons trained in tree care and surgery may use this saw.
www.tanakapowerequipment.com 4 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 3. Assembly procedures NOTE! Slightly move the bar back and forth and make sure the chain tension boss (4) fits into the hole (5) in the bar properly. 4. Confirm the direction of saw chain (1) is correct as in the figure, and align the chain on the sprocket.
www.tanakapowerequipment.com 5 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 4. Operating procedures Fuel (Fig. 2-1) WARNING! The chainsaw is equipped with a two-stroke engine. Alwa ys run the engine on fuel, which is mixed with oil. Provide good ventilation, when fueling or handling fuel.
www.tanakapowerequipment.com 6 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 CHAIN OIL (Fig. 2-1 B) Fill chain oil reservoir (2). Always use good quality chain oil.
www.tanakapowerequipment.com 7 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 Chain brake operation (Fig. 2-5) Chain brake (1) is designed to activate in an emergency such as kick-back action. Please check to verify that it works properly before use.
www.tanakapowerequipment.com 8 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 WARNING! Never use the saw with only one hand. You cannot control the saw properly and you may lose control and injure yourself severely. Keep the saw body close to your body to improve control and reduce strain.
www.tanakapowerequipment.com 9 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 WARNING! Always observe the general conditions of the tree. Look for decay and rot in the trunk which will make it more likely to snap and start to fall before you expect it.
www.tanakapowerequipment.com 10 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 LIMBING Limbing is removing the branches from a felled tree. WARNING! A majority of kickback accidents occur during limbing.
www.tanakapowerequipment.com 11 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 THICK LOG, LARGER THAN GUIDE BAR LENGTH Begin by cutting on the opposite side of the log. Pull the saw towards you followed pre vious procedure. (Fig. 2-7J) If the log is lying on the ground make a boring cut to avoid cutting into the ground.
www.tanakapowerequipment.com 12 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 In the carburetor, fuel is mixed with air. When the engine is test run at the factory, the carburetor is basically adjusted. A further adjustment may be required, accord ing to climate and altitude.
www.tanakapowerequipment.com 13 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 Cleaning the air filter Remove the air filter cover and the filter (1). Rinse it in warm soap suds. Check that the filter is dry before reassembly. An air filter that has been used for some time cannot be cleaned completely.
www.tanakapowerequipment.com 14 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 Guide bar (Fig. 3-5) Before using the machine, clean the groove and oiler port (1) in the bar with the special gauge offered as an optional accessory. Oiler port (Fig. 3-4) Clean the chain Oiler port (1) whenever possible.
www.tanakapowerequipment.com 15 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 LOWERING DEPTH GAUGES WITH A FILE 1) If you sharpen your cutters with a file holder, check and lower the depth. 2) Check depth gauges every third sharpening. 3) Place depth gauge tool on cutter.
www.tanakapowerequipment.com 16 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 Maintenance schedule Below you will find some general maintenance instructions. For further information please contact your service dealer. Daily maintenance • Clean the exterior of the unit.
www.tanakapowerequipment.com 17 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 6. Specifications.
www.tanakapowerequipment.com 18 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 Declaration of conformity Declaration de conformit6 Dichiarazione di conformita Konformitiitserkliirung Declaraci6n de conformidad Konformitetsdeklaration Tanaka Kogyo Co.
www.tanakapowerequipment.com 19 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 IMPORTANT NOTICE THIS INFORMATION IS FOR THE US AND CANADIAN MARKETS ONLY.
Een belangrijk punt na aankoop van elk apparaat Tanaka TCS-3401 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Tanaka TCS-3401 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Tanaka TCS-3401 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Tanaka TCS-3401 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Tanaka TCS-3401 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Tanaka TCS-3401 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Tanaka TCS-3401 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Tanaka TCS-3401 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
