Gebruiksaanwijzing /service van het product SX3i van de fabrikant Telular
Ga naar pagina of 27
P HONECELL SX3 i AMPS F IXED W IRELESS T ERMINAL U SER M ANUAL Total communications freedom at your fingertips...voice/fax/data. 12/08/99 Part No. 56016602 PHONECELL SX.
Intr oduction P HONECELL SX3i AMPS 2 U SER M ANUAL 12/08/99 Phone(s) Fax Machine AC Power Computer Modem l l PHONECELL SX Thank you for choosing the Phonecell ® SX3 Fixed Wireless T erminal (FWT) from T elular .
P HONECELL SX3i AMPS 3 U SER M ANUAL 12/08/99 T able of Contents Introduction ...............................................................................................2 T echnical Support .........................................................
P HONECELL SX3i AMPS 4 U SER M ANUAL 12/08/99 Getting S tarted... Pre-Inst allation Checklist Before attempting Phonecell SX3i installation, make sure you have the following component s, tools and materials. Qty . Description Supplied Not Supplied 1 Antenna (Spike, Magnetic-Mount, or Y agi) 4 2 6-V olt, 4.
Installation Summary P HONECELL SX3i AMPS 5 U SER M ANUAL 12/08/99 S tep 1. Choose an Antenna Location (pg. 6-7) · · Choose a location. · · Next, connect power to the FWT . · · Then, connect the antenna (not supplied) . · · Check the cellular signal strength and move the antenna until you achieve the best signal possible.
P HONECELL SX3i AMPS 6 U SER M ANUAL 12/08/99 S tep 1. Choose an Antenna Location Y our Phonecell SX3 receives operating commands from the cel- lular network and relies upon signal strength for proper opera- tion. Therefore, finding an antenna location with good signal strength is critical for call quality .
P HONECELL SX3i AMPS 7 U SER M ANUAL 12/08/99 WARNING! Never operate your Phonecell when any person is within 16 inches (40 cm) of the antenna. How to Connect the Antenna: 1) Connect the AC line cord from the power port on the front of the FWT to the AC power source see Figure 3.
P HONECELL SX3i AMPS 8 U SER M ANUAL 12/08/99 S tep 2. Plug In Y our T elephone Y our Phonecell SX3 lets you connect up to 5 pieces of standard telephone equip- ment into a cellular network.
P HONECELL SX3i AMPS 9 U SER M ANUAL 12/08/99 S tep 3. NAM/Phone Number Setup Y ou can program the Phonecell SX3 with an ordinary tone-dial (DTMF) telephone, which is sometimes referred to as a POTS (Plain Old T elephone Service) phone. NOTE: this programming mode is not accessible while you're in a call.
P HONECELL SX3i AMPS 10 U SER M ANUAL 12/08/99 NOTE: The following NAM Parameters are automatically set by the SID value in step 4 on the previous page. These step s 5 - 7 are only needed if you want to override the standard AMPS settings listed on the previous page.
Step #6 - How to Override the Number of Dedicated Control Channels. Press: # * 26 * _ _ # The spaces represent your 2-digit range of Dedicated Control Channels. When you first turn on the Phonecell, it automatically scans up to 21 control channels looking for your cellular provider .
P HONECELL SX3i AMPS 12 U SER M ANUAL 12/08/99 1) Make sure that the switch is in the of f position. 2) Disconnect AC and/or DC power cord(s). 3) Locate the battery compartment, which is next to the silver transceiver on the back of the FWT -- see Figure.
P HONECELL SX3i AMPS 13 U SER M ANUAL 12/08/99 Battery Installation Continued 7) Connect the batteries as follows: · · Connect one end of the BLUE wire (attached to the battery cover) to the BLACK (-) terminal of the second battery · · Attach the other end of the BLUE wire to the RED (+) terminal of the first battery as shown in Fig.
P HONECELL SX3i AMPS 14 U SER M ANUAL 12/08/99 S tep 5. Install Y our Phonecell 5a. W all-Mount Inst allation 1) Hold the mounting template against the wall and mark two holes for the mounting screws see Figure 1 1. 2) Drill two holes for the mounting screws see Figure 12.
P HONECELL SX3i AMPS 15 U SER M ANUAL 12/08/99 IMPORT ANT! Y our Phonecell SX3 must be placed or mounted on a flat, level surface to allow proper ventilation. Do not block the air vents or the space beneath your Phonecell as this could cause the unit to overheat and fail.
P HONECELL SX3i AMPS 16 U SER M ANUAL 12/08/99 Phonecell Operation LED Status T able LED Color LED Activity Description RED Flashing Malfunction. Hardware fault detected. RED Continuous No cellular service. YELLOW Continuous Moderate cellular signal strength.
P HONECELL SX3i AMPS 17 U SER M ANUAL 12/08/99 Phonecell Operation Continued Import ant T ones and Alert s No-Service T one When cellular service is not available, the receiver emits a No-Service (fast-beeping) tone instead of the normal (steady) dial tone.
P HONECELL SX3i AMPS 18 U SER M ANUAL 12/08/99 V ariable Dial T ime (Auto SEND Delay) Option When you place a call, your Phonecell SX3 automatically sends the phone num- ber over the cellular network after you dial the last digit just like a landline phone.
P HONECELL SX3i AMPS 19 U SER M ANUAL 12/08/99 Three-W ay Conference Calls - For three-way conference calls, the Out-of-Band Signaling option must be enabled. Pressing the HOOKFLASH function transmits the SEND command. Please see the Data After SEND option below .
P HONECELL SX3i AMPS 20 U SER M ANUAL 12/08/99 Phonecell SX3 T r oubleshooting T elephone Service is Not W orking If the telephone service is not working, first check the operation of the telephone equipment and wiring connected to your Phonecell SX3 .
P HONECELL SX3i AMPS 21 U SER M ANUAL 12/08/99 Y our Phonecell SX3 FWT (Fixed Wireless T erminal) functions as both a radio transmitter and receiver . When it is ON, the FWT receives and sends out radio frequency (RF) energy . The unit may operate in frequency ranges between 824 MHz and 894 MHz.
P HONECELL SX3i AMPS 22 U SER M ANUAL 12/08/99 Safety Information Continued Batteries All batteries can cause property damage, injury , or burns if a conductive material, such as jewelry , keys, or beaded chains, touches exposed terminals. The material may complete an electrical circuit (short circuit) and become quite HOT .
P HONECELL SX3i AMPS 23 U SER M ANUAL 12/08/99 Safety Information Continued Blasting Areas Construction crews often use remote control RF devices to set off explosives. Therefore, to avoid interfering with blasting oper- ations, turn your Phonecell SX3 OFF when in a "blasting area" or in areas posted: "T urn off two-way radio.
P HONECELL SX3i AMPS 24 U SER M ANUAL 12/08/99 AMPS T echnician Programming AMPS T echnician Programming Commands The Phonecell SX3 can be programmed on location with an ordinary telephone, which is sometimes referred to as a POTS (Plain Old T elephone Set) phone.
P HONECELL SX3i AMPS 25 U SER M ANUAL 12/08/99 How to Set the Access Overload Class (ACCOLC) Use the following key sequence to set the ACCOLC: Press: # * 2 * < ACCOLC > # The < > brackets represent the 2-digit ACCOLC.
P HONECELL SX3i AMPS 26 U SER M ANUAL 12/08/99 T echnician Programming Commands Continued How to Set the Post-Receiver Of f-Hook (ROH) Option Use the following key sequence to set the post-ROH opt.
Part No. 56016602 ©1999 T elular Corporation, all rights reserved. Printed in the USA..
Een belangrijk punt na aankoop van elk apparaat Telular SX3i (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Telular SX3i heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Telular SX3i vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Telular SX3i leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Telular SX3i krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Telular SX3i bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Telular SX3i kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Telular SX3i . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.