Gebruiksaanwijzing /service van het product MO-425 van de fabrikant Thermo Products
Ga naar pagina of 20
MO-425 ECN 4392- MA OIL FURNACE GENERAL SERVICE AND MAINTENANCE MANUAL FOR USE WITH THERMO PRIDE OIL FURNACES THERMO PRODUCT S, LLC . PO BOX 217 NORTH JUDSO N, IN 46366 PHONE: (574) 896-2133.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. i TABLE OF C ONTENTS SECTION BEGINNING P AGE I . GENERAL I NSTRUCTI ONS 1 I I . I N S T A L L A T I O N 2 A. CHI MNEY 2 1. PROPER CHI MNEY SI ZE 2 2. PREVENTION OF CHI MNEY CONDENSING 3 3.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. 1 I. GENERAL INSTRUCTIONS - READ BEFORE START OF INSTALL ATION 1.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. 2 If the " entir e" build ing is unusually tight ly construc ted a nd/or has an exha ust fan insta lled, a low pr essure z one co uld b e cre ated w ithin th e structu re.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. 3 2. PREVENTION OF CHIM NEY CONDENSING: Stack gas m ay do one of tw o things as it escapes u p the chim ney : A. Rem ain en tirely in a gaseous state if the in ternal chim ney w all tem perature is above th e dew poin t, or B.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. 4 3. PROPER CHIM NEY HEIGHT: The chimney shall ter minate a t lea st 3 fee t abo ve the highe st po int where it p asses thro ugh the ro of of a build ing and a t least 2 feet hig her than any portion of a bu ilding w ith in a horizontal dis tance of 10 feet.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. 5 5. PRO PER CHIM NEY BOTTO M LEVEL: In cases w here the chim ney extends to the basem ent floor, the draft can us.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 6 Fig. 7: Alternate constructions that allow reduced clearances to com bustible materials.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 7 The vent conn ector pipe between the f urnace an d chim ney shall be of equal diam eter as the flue outlet of th e furnace. The vent connector pipe m ust be m ade of 24 gauge (or thicker) corrosion-resistant steel.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 8 Fig. 8: Supply air duct sizing Example The RETURN AIR DUCT SYSTEM should eq ual the w arm air duct sy stem in airflow capabilities.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 9 D. OIL TANK & PIPING: ? ? ? ? WARNING: All local codes and ordinances take precedence wi th regard to tank and oil lines.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 10 Below th e w iring diag rams for the variou s T herm o Pride oil furnace m odels.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 11 G. INITIAL BURNER OPERATION: IMPORTANT: READ B URNER INSTRUCTION MANUAL (INCLUDED WITH BURNER) BEFORE CONTINUING. To successfully service an d initially set up the oil furnace, y ou must use th e follo w ing instru men ts: A.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 12 For exam ple, if a 13% CO 2 (3.5% O 2 ) is measu red at a trace of smoke, open the air sh utter until a zero sm oke reading is obtained w ith a 12% C O 2 or 4.5% O 2 .
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 13 TURN T'STAT SE TTING ABOVE ROO M TEMPERATURE TURN THERMOSTAT TO CALL FOR HEA T DOES TH ERMOSTAT MAKE CON TA.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 14 POSITI ON THEM PER BURNER MANUFACTURERS INSTRUCTIONS REPLACE IG NITI ON TRANSFORM ER ARE THE ELECTRODES ARCING? .
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 15 PROPER COMBUST ION ACHIEVED? IS THE PROBLEM DELAYED IGNITION? IS PUMP PRESSURE SET ACCORDING TO BURNER APPLICATI.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 16 GO TO PROPER COMBUST ION ACHIEVED SECTI ON ABOVE AND SET COMBUSTION ADJUST BLOWER SPEED TO RAISE TEM PERATURE RISE. -- INCREASE L ENGTH OF BURNER ON CYCLE -- INSULATE CHIM ENY W ITH CHIMNEY LINER.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 17 B. CAD CELL CHECK OUT PROCEDURE: 1. Remove cad cell lead w ires, then start th e burner. Shortly after burner st arts, place a tem porary jum per between term inal f - f.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 18 ? ? ? ? CAUTION: Do not attempt to start burn er when: 1.Ex cess oil has accumulated 2.W hen the furnace or burner is full of vapor 3.W hen the combustion chamber is very hot.
Een belangrijk punt na aankoop van elk apparaat Thermo Products MO-425 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Thermo Products MO-425 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Thermo Products MO-425 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Thermo Products MO-425 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Thermo Products MO-425 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Thermo Products MO-425 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Thermo Products MO-425 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Thermo Products MO-425 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
