Gebruiksaanwijzing /service van het product PSMLBU van de fabrikant Toshiba
Ga naar pagina of 252
GMAD00210010 08/09 If you need assistance: ❖ T oshiba’ s Support W eb site pcsupport.toshiba.com ❖ T oshiba Customer Support Center Calling within the United States (800) 457 -7777 Calling from outside the United States (949) 859 -4273 For more in formation, see “If Something Goes Wrong” on page 183 in this gui de.
2 5.375 x 8.375 ver 2.3 Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
3 5.375 x 8.375 ver 2.3 Critical Applications The computer you have purchased is not designed for any “critical applications. ” “Critical applications” means life s upport sy stems, medical ap.
4 5.375 x 8.375 ver 2.3 This device complies with P art 15 of the FCC Rules. Operation is subject to the following tw o conditions: ❖ This device may not cause harmful interference. ❖ This device must accept an y interferen ce received, including interference that may cause undesired operatio n.
5 5.375 x 8.375 ver 2.3 Connection to party line service is subject to state tarif fs. Contact the state public utility commission, public se rvice co mmission or corpor ation commission for information. T elephone Company Procedures The goal of the telephone company is to pro vide you with the best service it can.
6 5.375 x 8.375 ver 2.3 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable yo ur alarm equipment. If you hav e questions abou t what will disable alarm equipment, consult your telephone compan y or a qualified installer .
7 5.375 x 8.375 ver 2.3 Wireless Interoperability The TOSHIB A W ireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology , and is compliant to: ❖ The IEEE 802.
8 5.375 x 8.375 ver 2.3 Wireless LAN and Y our Health W ireless LAN products, like other radio de vices, emit radio frequency electromagnetic energy . The lev el of energy emitted by W i reless LAN devices howe ver is f ar much less than the elect romagnetic energy emitted by wireless devices lik e for example mobile phones.
9 5.375 x 8.375 ver 2.3 Canada – Indust ry Canada (IC) This device complies with RS S 210 of Industry Canada. The installer of this radio equipment mu st ensure that the antenna is located or pointe.
10 5.375 x 8.375 ver 2.3 EU Declaration of Conformity TOSHIB A declares that this product conforms to the follo wing Standards: This product is carrying the CE-Mark in accordance w ith the related European Directiv es. The party responsib le for CE-Marking is TOSHIB A Europe GmbH, Hammfelddamm 8, 41460 Neuss, Ger many .
11 5.375 x 8.375 ver 2.3 VCCI Class B Information Modem W arning Notice Conformity Statement The equipment has been ap prov ed to [Commission D ecision “CTR21”] for pan- European single terminal connection to the Public Switched T elephone Network (PSTN).
12 5.375 x 8.375 ver 2.3 Using this Equipment in Japan In Japan, the frequency bandwi dth of 2,400 MHz to 2,483.5 MHz for second generation low-po wer data communicatio n systems such as this equipment ov erlaps that of mobile object identifi cation systems (premises radio station and specified lo w-power radio station).
13 5.375 x 8.375 ver 2.3 The indication sho wn belo w appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 FH: This equipment uses FH-SS modulation. 3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequenc y bandwidth from 2,400 MHz to 2,483.
14 5.375 x 8.375 ver 2.3 Radio Approvals for Wireless Devices The following information is de pendent on what type of wi reless de vice is in your computer .
15 5.375 x 8.375 ver 2.3 For these r easons Intel ® cannot permit any manipulat ion b y third parties of the software pro vided in binary format with the wireless Wi MAX™ adapters (e.
16 5.375 x 8.375 ver 2.3 In some situations or en vironments, the use of W ireless W AN may be restricted by the proprietor of the b uilding or responsible representativ es of the organization.
17 5.375 x 8.375 ver 2.3 Canada – Industry Canada (IC) W ireless W AN complies with RSS-129, RSS-133 Industry Canad a. The installer of this radio equipment mu st ensure that the antenna is located .
18 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Intel ® Wireless Wi-Fi ® Link 5100/5300 Series This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
19 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Atheros ® Wireless Wi-Fi ® Link AR5B95 Series This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
20 5.375 x 8.375 ver 2.3 Europe - Restrictions for us e of 2.4 GHz Frequencies in European Community Countries Kuwai t Kyrgyzs tan L atv ia Lebanon Lesotho Liechtenstein Lithuania Luxembourg Macedonia.
21 5.375 x 8.375 ver 2.3 Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries O: allowed x: forbidden France: Restricted frequency band: only channels 1 to 7 (2400 MHz and 2454 MHz respectiv ely) may be used outdoors in France.
22 5.375 x 8.375 ver 2.3 ❖ T o remain in conformance with Euro pean spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply . The user should use the wireless LAN utility to check the current channel of operation.
23 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8191SE This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
24 5.375 x 8.375 ver 2.3 Hong K ong Hungary Iceland India Indonesia Ireland Israel Italy Jamaica Japan Jordan Kazakhstan Ken ya Kuwait K yrgyzstan Latvia Lebanon Liechtenstein Lithuania Lux embourg Ma.
25 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8187B This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
26 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use for the Intel ® PRO/Wireless 3945ABG Network Connection This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
27 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Intel ® Wireless Wi-Fi ® Link 4965AGN This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
28 5.375 x 8.375 ver 2.3 Bluetooth ® Wireless T echnolo gy Interoperability Bluetooth ® Cards from TOSHIB A are designed to be interoperable with an y product with Bluetooth wireless technology that.
29 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use ( Bluetooth ® wireless technology) Bluetooth ® Card from T oshiba equipment is ap proved to the radio standard by the countries/regions in the follo wing table. Do not use this equipment except in th e countries/regions in the follow ing table.
30 5.375 x 8.375 ver 2.3 In some situatio ns or en vironments, the use of Bluetooth wireless technology may be restricted by the proprietor of th e building or responsible representati ves of the organization.
31 5.375 x 8.375 ver 2.3 The legal communications mentioned in the abov e item refer to radio communications operated in accordan ce with telecommunication laws and regulations.
32 5.375 x 8.375 ver 2.3 Copyright This guide is copyrighted by T oshiba Amer ica Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide canno t be reproduced in any form without the prior written permission of T o shiba.
33 5.375 x 8.375 ver 2.3 T rademarks Satellite, ConfigFree, and eco utility ar e either registered trademarks or trademarks of T oshiba Am erica Information Systems, Inc. and/or T oshiba Corporation. Adobe and Photoshop are either registered trademarks or tr ademarks of Adobe Systems Incorporated in the Unite d States and/or other countries.
34 5.375 x 8.375 v er 2.3 Contents Introduction ................ ................................................................ 42 This guide ...............................................................44 Safety icons ............................
35 Contents 5.375 x 8.375 v er 2.3 Turning on the power .......................................55 Setting up your software ...................................56 Registering your computer with Toshiba ................56 Adding optional external devices.
36 Contents 5.375 x 8.375 v er 2.3 Using and configuring Hibernation mode .........92 Using and configuring Sleep mode ...................94 Closing the display panel ..................................97 Customizing your co mputer’s settings .......
37 Contents 5.375 x 8.375 v er 2.3 Inserting an optical disc (tray-type drive) ....... 113 Playing an audio CD ........................................114 Playing optical media ......................................114 Recording optical media ........
38 Contents 5.375 x 8.375 v er 2.3 Disposing of used batteries ..................................133 Traveling tips ........................................................134 Chapter 4: Exploring Y our Computer’ s Features ................... 135 Exploring the desktop .
39 Contents 5.375 x 8.375 v er 2.3 TOSHIBA Application Installer ...............................156 Setting passwords ................................................ 157 Using an instant password ..............................157 Using a supervisor password .
40 Contents 5.375 x 8.375 v er 2.3 Chapter 6: If Something Goes Wrong ............ ........................ 183 Problems that are easy to fix ................................183 Problems when you turn on the computer ............184 The Windows ® operating system is not working .
41 Contents 5.375 x 8.375 v er 2.3 Appendix A: Hot Keys/TOSHI BA Cards ........... ...................... 214 Hot Key Cards .......................................................214 Using the Hot K ey Cards .................................215 Application Cards .
42 I n t roduct ion W elcome to the world of powerful, portable, multimedia computing. W ith your T osh iba computer , your work and entertainment can accompan y you where ver you go.
43 Introduction 5.375 x 8.375 ver 2.3 According to the EP A, a computer meeting the new ENERGY ST AR ® specifications will use between 20% and 50% less energ y depending on how it is used. If all U.S. household and businesses replaced old computers with ne w ENERGY ST AR ® qualified models, we would sav e more than $1.
44 Introd uctio n This guide 5.375 x 8.375 ver 2.3 The product specifications and configuration information are designed for a product Series. Y our particular model may not have all the features and specifications listed or illustrated.
45 Introduction Safety icons 5.375 x 8.375 ver 2.3 Safety icons This manual contains safety inst ructions that must be observed to av oid potential hazards that co uld result in personal injuries, damage to your equipmen t, or loss of data.
46 Introd uctio n Other documentation 5.375 x 8.375 ver 2.3 Y our computer’ s features and specifications Certain computer chassis are de signed to accommodate all possible configurations for an entire product Series.
47 Chapter 1 Getting Started This chapter provides tips for us ing your computer ef fecti vely , summarizes how to connect components, and explains what to do the first time you use your computer . The “Instruction Manual for Safet y and Comfort, ” that is shipped with your computer, contains impo rtant safety information.
48 Getting Started Selecting a place to work T o keep your computer in prime operating condition, protect you r work area from: ❖ Dust, moisture, and direct sunlig ht. ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones.
49 Getting Started Selecting a place to work ❖ Avoid prolonged physical contact with the underside or s urface of the computer . ❖ Computer base and palm rest can become hot! Avoid prolonged contact to prevent heat injur y to skin.
50 Getting Started Setting up your computer Important information on your computer’ s cooling fan Y our computer may have a CPU cooling fan that coo ls the CPU by drawing outside air into the computer .
51 Getting Started Connecting to a po wer sour ce Please handle your computer carefully to avoi d scratching or damaging the surface. Connecting to a power source Y our computer requires power to operate. Use the po wer cord/cable and A C adaptor to connect the comput er to a liv e electrical outlet, or to charge the computer’ s battery .
52 Getting Started Connecting to a power so ur ce T o connect A C power to the computer: 1 Connect the po wer cord/cable to the A C adaptor . (Sample Illustration) Connecting the power cord/cable to t.
53 Getting Started Char ging the main battery The computer’ s main battery light gives you an indication of the main battery’ s current char ge: ❖ Glows amber while the main battery is bei ng ch.
54 Getting Started Using the computer for the fir st time Battery life and charge time may var y depending on the applications, power management settings, and features used. Using the computer for the first time The computer is now ready for you to turn it on and be gin using it.
55 Getting Started Using the computer for the f irst time Small bright dots ma y appear on your screen displa y when you turn on your computer . Y our disp lay contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precision technology .
56 Getting Started Re gistering your computer with T oshiba Setting up your software When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely . The names o f windows displaye d, and the order in which windows appear , may va ry acco rding to your software setup c hoices.
57 Getting Started Adding memory (optional) Adding memory (optional) HINT : T o purchase additional memory modules, see the accessories information packaged with your system or visit accessories.toshiba.com . Y o u r c o m pu t e r comes with enough memory to run most of today’ s popular applications.
58 Getting Started Adding memory (optional) For this model, Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A. If the computer is on, begin at step 1 ; otherwise, skip t o step 3 .
59 Getting Started Adding memory (optional) 6 Using a small Phillips screwdri ver , loosen the captiv e screws that secure the memory module slot co ver . (Sample Illustration) Removing the memory module slot cover 7 Remove the memory module slot cover .
60 Getting Started Adding memory (optional) If your system has the memory modules stacked on top of one another , you must remove the top module first before removing/installing the bottom module. For this model, Slot A is the bottom slot. Slot B is the top slot.
61 Getting Started Adding memory (optional) 13 Once the module’ s connector is fu lly inserted into the socket, press downw ard on the top edge of the module to seat the module into the latches at the sides of the so cket. These latches should “snap” into place securely with th e corresponding cutouts in the side of the module.
62 Getting Started Adding memory (optional) 16 T urn the computer right side up. Make sure to remov e the soft cloth from the work surface be fore restarting the computer .
63 Getting Started Adding memory (optional) Do not try to remove a memor y module with the computer turned on. Y ou can damage the computer and the memor y module. Do not remove the memory module while the computer is in Sleep or Hibernation mode. The computer could hang up the next time you turn it on and data in memory will be lost.
64 Getting Started Adding memory (optional) 3 Gently lift the me m o ry module to a 30-degree angle and slide it out of the slot. (Sample Illustration) Removing the memory module 4 Replace the memory modu le slot cov er and secure it using the screws.
65 Getting Started Recovering the Internal Stora ge Drive 7 Reconnect the cables. 8 Restart the computer . TECHNICAL NOTE: Y ou must have at least one memory module installed for the computer to work. Checking total memory When you add or remove a memory mo d u l e , you can check that the computer has recognized the change.
66 Getting Started Recovering the Internal Stor age Drive ❖ During the internal storage drive recovery process it is strongly recommended that your computer be connected to an external power source via the AC adaptor . ❖ It is strongly recommended that you create recov er y DVDs/media before using your system for the first time.
67 Getting Started Recovering the Internal Stora ge Drive During the recovery process it is strongly recommended that your computer be connected to an external power source via the AC adaptor .
68 Getting Started Recovering the Internal Stor age Drive 5 When the T oshiba Recov ery W izard opens and the Selecting a process screen displays, select Recovery of F actory Default Software and then click Next . (Sample Image) Selecting a Pr ocess scr een 6 The Recov ery of Factory Defaul t Software screen appears.
69 Getting Started Recovering the Internal Stora ge Drive 7 Click Next . A confirmation message displays reminding you that all data will be lost during the recov ery process. Be sure to sav e your work to e xternal media before proceeding. 8 Click Next to be gin the recovery .
70 Getting Started Recovering the Internal Stor age Drive 4 A warning screen appears, statin g that when the reco very is ex ecuted all data will be deleted and rewritten.
71 Getting Started Recovering the Internal Stora ge Drive 6 The Recov ery of Factory Defaul t Software screen appears. Select Recover to a custom s ize portion . (Sample Image) Reco very of F a ctory Defa ult Software scr een 7 Use the on-screen arro w buttons in The size of driv e C: fi e ld to set the partition size.
72 Getting Started Recovering the Internal Stor age Drive Y ou can recov er the C: driv e without affecting other partitions by either using the utilities stored on your computer’ s internal storage dri ve or b y using recovery D VDs/me dia, if you have created such media.
73 Getting Started Recovering the Internal Stora ge Drive 5 When the T oshiba Recov ery W i zard opens and the Selecting a process screen displays, select Recovery of F actory Default Software and then click Next . (Sample Image) Selecting a Pr ocess scr een 6 The Recov ery of Factory Defaul t Software screen appears.
74 Getting Started Recovering the Internal Stor age Drive 8 Click Next to be gin the recov ery . When the process is complete, a message displays, indicating that the C: dri ve has been recov ered. 9 Press any k ey on the keyboard to restart the computer .
75 Getting Started Recovering the Internal Stora ge Drive Restoring from recovery DVDs/media The recovery process deletes information stored on the internal storage drive.
76 Getting Started Erasing the Internal Stora ge Drive 8 Select one of the following options: ❖ Recover to out-of-box state —If you want to reco ver the original factory image (retur ning the computer to its out- of-box state).
77 Getting Started Erasing the Internal Storag e Drive ❖ T o access the Recovery W izard on yo ur recov ery DV D s / m e d i a : Insert the first recov ery D VD into the optical driv e and po wer on th e computer . When the initial screen displays, press F12 .
78 Getting Started Checking the inte rnal stor age drive operating status Checking the internal storage drive operating status After restoring your inte rnal storag e driv e, you can check its status as follo ws: 1 Click Start . 2 Right-click Computer .
79 Getting Started Using the T ouchP ad™ ❖ Zoom out to see more information at once (Sample Illustration) The T ouchP ad and associated con tr ol b uttons Refer to the table below for specif ic instructions on perf orming each operation.
80 Getting Started Using the T ouchP ad™ Open or activate an item 1 Move the pointer to the item you want to open/activate. 2 Do one of the following: ❖ T ap the T ouchPad twice in rapid successio.
81 Getting Started Using the T ouchP ad™ Adjusting T ouchPad™ settings While you are typing, the on-screen pointer may seem to move or jump around “by itself” to ran dom locations on the screen. The on-screen pointer may also seem to automatical ly select text, click buttons, and activ ate other user interface elements.
82 Getting Started Using external display de vices accidental light touches or taps on the T ouchPad may select an item or text on the screen, and potentially the item or text may be replaced by the ne xt character you type. ❖ T emporarily disabl e the T ouchPad, so that it does not respond to touch or button presses while you type.
83 Getting Started Using external display de vices (Sample Illustration) V ideo ports Connecting the display device If you are connecting a television or other video display device to the computer’ s HDMI™ Out port, refer to “Connecting an HDMI™-compatible television or VCR/D VD player” on page 83 .
84 Getting Started Using external display de vices ❖ Use a TV remote control to launch, operate and close applications on your comput er . ❖ T urn on a TV when the HDMI output is selected using the Fn+F5 key . ❖ Switch the vi deo output (HDMI or LCD) wh en execu ting certain desktop icons.
85 Getting Started Using an external k e yboard This hot key c ycles through the settings in the fo llo wing order: ❖ Built-in display only ❖ Built-in display and external monitor sim ultaneously .
86 Getting Started Using a mouse Using a mouse Y ou may want to use a mouse instead of the computer’ s built-in T o uchPad™. Y ou can use a USB-compatible mouse. Connecting a printer Y our printer documentation may require you to install the printer software before physically connecting the printe r to your computer .
87 Getting Started T urning off the computer Setting up a printer Some printers require a specific installation process. Refer to your printer installation guide for instructions before completing the following procedure. If your printer does not support Plug and Play , follo w these steps to set it up for the first time.
88 Getting Started T urning off the computer Options for turning off the computer Depending on the operating sy stem installed, you have more than one option av ailable for turning off the computer: Shut down, Hibernate, and Sleep. Each option has its advantages.
89 Getting Started T urning off the computer For information on ho w to use and configure Hibernation mode see “Using and configuring Hibernation mode” on page 92 .
90 Getting Started T urning off the computer Using the Shut down command The Shut do wn command complet ely shuts down the computer without saving your work or the cu rrent state of th e computer . This command closes all open program s, shuts down the operating system, and then turns off your computer .
91 Getting Started T urning off the computer 3 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. 4 Double-click P ower b uttons and lid to display the actions that you can configure.
92 Getting Started T urning off the computer Restarting your computer T o start the computer up again, press the po wer b utton unti l the ON/OFF light glows white. If you turn off the computer by closing the display panel, you can start it again by open i ng the display panel .
93 Getting Started T urning off the computer 3 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. 4 Double-click P ower b uttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of P ower Options scr een 5 Select Hibernate for the options you want.
94 Getting Started T urning off the computer 6 Click App l y . 7 Click OK . Once the computer is conf igured, you can place it into Hibernation mode by either pressing the po wer button or closing the display panel, depending on the Hibernation options set.
95 Getting Started T urning off the computer Configuring Sleep mode options Y ou can place the computer into Sleep mode by either pressing the power b utton or closing the display panel. Y ou can also specify an amount of time after which the computer au tomatically g oes into Sleep mode.
96 Getting Started T urning off the computer 4 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. 5 Double-click P ower b uttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of P ower Options screen 6 Select Sleep for the options you want.
97 Getting Started Customizing your computer’ s settings Starting again from Sleep mode T o start up the computer from Sleep mode, press the power b utton until the ON/OF F light glows white.
98 Getting Started Caring for your computer Moving the computer Before moving your computer, e ven across the room, make sure all dri ve acti vity has ended (the internal storage driv e and optical driv e indicator lights stop glowing) and al l external peripheral cables are disconnected.
99 Chapter 2 Learning t he Basics This chapter giv es some computing tips and provides important information about basic features. Computing tips ❖ Sav e your work frequently . Y our work stays in the computer’ s temporary memory until you sav e it to the internal storage drive.
100 Learning the Basics Using the ke yboar d ❖ Back up your files to e xternal media on a regular basis. Label the backup copies clearly and store them in a safe place.
101 Learning the Basics Using the ke yboar d Character keys T y ping with the character keys is very mu ch li ke t yp in g o n a typewriter , e xcept that: ❖ The space bar creates a space char acter instead of just passing ov er an area of the page.
102 Learning the Basics Using the ke yboar d F1 through F12 are called function keys because the y ex ecute programmed functions when pressed. Used in combin ation with the Fn key , fun ction keys marked with icons ex ecute specific functions on the computer .
103 Learning the Basics Starting a pr ogr am Using the overlay to type numeric data The keys with the numbers on th eir right front are the numeric ov erlay keys. T o turn the numeric ov erlay on, press Fn and F11 simultaneously . The numeric overlay light glo ws wh en the numeric ov erlay is on.
104 Learning the Basics Starting a pr ogram Starting a program from the Start menu When you install a prog ram, the operating syst em usually puts an icon in the Al l Programs menu.
105 Learning the Basics Starting a pr ogr am 4 In the right part of the wi ndow , doubl e-click the folder containing the program, in this case Program Files . W indows ® Explorer shows the contents of the Program Files folder on the right side of the windo w .
106 Learning the Basics Saving your work Saving your work Before you turn off the computer using the Shut down command, sav e your work on the internal storage driv e, diskette, flash media, or optical disc. This is one of the most important rules of computing.
107 Learning the Basics Printing your work File names The W indo ws ® operating system supp orts long file names that can contain up to 260 characters and can include spaces. Some applications do not support long file names and require file names limited to no more th an eight characters.
108 Learning the Basics Backing up your work 2 Click on the arrow in the upper -left corner of your W indows ® -based application to display th e drop-down menu, and then click Print . The program displays a Print dialog box. (Sample Image) Print dialog box 3 Specify the print parameters.
109 Learning the Basics Using the optical drive Restoring your work T o restore information from your backu p media to your internal storage driv e, use the Restore option in the Windo ws ® Backup and Restore program. Look in the online Help or your op erating system documentation for informati on on restoring files.
110 Learning the Basics Using the optical drive For optimum DVD performance, it is recommended that you play DVDs while running the computer on AC power . When viewing DVD movies use the DVD Player software that came with your computer . Optical drive components The optical dri ve is located on th e side of the computer .
111 Learning the Basics Using the optical drive Manual eject hole (a vailable on certain models) —Use if you need to release the disc tray when the power is off. Use a straightened paper clip or o ther na rro w object to press the manual eject button located inside the hole.
112 Learning the Basics Using the optical drive Handle DVDs and CDs carefully , making contact only with the center hole and edge. Do not touch the surface of the disc. Do not s tack discs. If you incorrectly handle the discs, you c ould lose data. If the disc is dusty , clean it as described in “Caring for optical discs” on page 116 .
113 Learning the Basics Using the optical drive Inserting an optical disc (tray-type drive) (A vailable on certain models) T o insert an optical disc into the dri ve: 1 Make sure the computer is turned on. The dri ve will not open if the computer’ s power is of f.
114 Learning the Basics Using the optical drive 7 Gently press the disc onto the center spindle until it clicks into place. Handle DVDs and CDs carefully , making contact only with the center hole and edge. Do not touch the surface of the disc. Do not s tack discs.
115 Learning the Basics Using the optical drive If your disc does not run using this m ethod, try using an application that is associated with the media on the disc. For example, if it is a music CD, open Windo ws Media ® Player and use it to select and then play the CD.
116 Learning the Basics T oshiba’ s online r esour ces 2 Pull the tray out until it is fully open , remove the disc, and place it in its protecti ve co ver .
117 Chapter 3 Mobile Computing This chapter cov ers all aspects of using your com puter while trav eling. T oshiba’ s energy-saver design Y our computer enters a low-po wer suspension mode when it is not being used, thereby conserving energy and sa ving money in the process.
118 Mobile Computing Running the computer on battery power Battery Notice Battery life may vary considerably from specifications depending on product model, configuration, applications, power management settings and features utilized, as well as th e natural performance variations produced by the design of indi vidual components.
119 Mobile Computing Char ging ba tteries Power management Y our computer ships with t he power management options preset to a configuration that will prov ide the most stable opera ting en vironment and optimum system performan ce for both A C power and battery modes.
120 Mobile Computing Char gi ng batteries Charging the main battery T o charge the main battery while it is in your computer , plug the computer into a li ve electrical ou tlet.
121 Mobile Computing Monitoring main battery power T o recharge the R T C battery , plug th e computer into a li ve electrical outlet and leav e the computer powered on for 24 hours. It is seldom necessary to charge the RTC battery because it charges while the computer is on.
122 Mobile Computing Monitoring main battery power HINT : Be careful not to confuse the battery light ( ), the ON/OFF light ( ), and the powe r button light (near the upper -left corner of the keyboard).
123 Mobile Computing Monitoring main battery power Mov e the pointer ov er the po wer icon in the notification area, see “Finding your way around the desktop” on page 136 for more information on the notification area. A pop-up message displays the remaining battery power as a percentage.
124 Mobile Computing Monitoring main battery power T o change the default notification settings: 1 Click Start , Contro l Panel , System and Security , and then Po wer Options . The Po wer Options window appears. 2 Click Change pl an settings under the power plan to be customized.
125 Mobile Computing Monitoring main battery power There are v arious ways in which you can conserv e power and extend the operating time of your battery: ❖ Enable Sleep or Hibernation, which saves .
126 Mobile Computing Monitoring main battery power 2 Select an appropriate plan for your work en vironment or create your own custom plan. 3 Click Create a po wer plan in the left pane to set up a new plan. T o edit a plan or to edit advanced settings, continue to the following steps.
127 Mobile Computing Using the T OSHIB A eco power plan 2 While continuing to press Fn , press F2 until you select the desired Power Plan. The Po wer Plan options are: eco and Balanced. 3 Release the Fn key . The hot key card disappears. Y ou are now in the selected mode.
128 Mobile Computing Changing the main battery Changing the main batter y When your main battery has ru n out of power , you have two options: plug in the A C adaptor or install a char ged main battery .
129 Mobile Computing Changing the main battery 5 Slide the battery release lock to the unlo cked position. (Sample Illustration) Unlocking the battery r elease lock 6 Slide the battery release latch to release the battery . 7 Pull the discharged battery out of the computer .
130 Mobile Computing Changing the main battery Inserting a charged battery T o insert a battery: 1 W ipe the terminals of the charge d battery with a clean cloth to ensure a good connection. 2 Insert the charged battery into the slot until the latch clicks.
131 Mobile Computing T aking car e of your battery 4 T urn the computer right side up. 5 Reconnect any cables that were remov ed in step 3 of “Removing the battery from the computer” on page 128 . 6 Restart the computer . T aking care of your batter y The follo wing sections offer tips on how to take care of your battery and prolong its life.
132 Mobile Computing T aking car e of your battery Maintaining your batter y Fully discharging your battery pack will allo w better accurac y of the battery meter . T o fully discharge your battery pack: ❖ Periodically , disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges.
133 Mobile Computing Disposing of used batteries Disposing of used batteries The life of a battery pack depends on usage. When the battery pack needs replacing, the main batt ery light flashes amber shortly after you hav e fully rech arged the battery .
134 Mobile Computing T raveling tips Notice regarding CR coin ce ll batter ies, applicable to California, U.S.A. only: Perchlorate Material - special handling may apply .
135 Chapter 4 Exploring Y our Computer’ s Features In this chap ter , you will explore so me of the special features of your computer . Exploring the desktop The desktop is the launching pad for everything you can do in the W indows ® operating system.
136 Exploring Y our Computer’ s Features Explorin g the desktop Finding your way around the desktop Y our computer’ s desktop includes sev eral standard features: icons, Start button, taskbar , notification area, and background pattern.
137 Exploring Y our Computer’ s Features Exploring the desktop Y our desktop may contain other icons depe nding on your configuration. See W indo ws ® online Help for more specific information on each icon and ho w to use it.
138 Exploring Y our Computer’ s Features Setting up for communications Setting up for communications T o connect to the Internet, use an online service, or communicate across the telephone lines wit.
139 Exploring Y our Computer’ s Features Setting up for communications Connecting your computer to a network Y ou can connect your computer to a network to increase its capabilities and functionali ty using one of its communication ports.
140 Exploring Y our Computer’ s Features Setting up for communications ❖ Communicate with your of fice’ s local area network (LAN) or larger corporate wide area netw ork (W AN) For specif ic information about connecting to a LAN or W AN, consult your network administrator .
141 Exploring Y our Computer’ s Features An overview of using the Internet Now you are ready to send a fax or use the modem to connect to an online service or the Internet.
142 Exploring Y our Computer’ s Features An overview of using the Internet Connecting to the Internet T o connect to the Internet, you need: ❖ A modem and telephone line, or a LAN connection ❖ A W eb browser ❖ An Internet Service Provider (ISP) account Once you hav e established an ISP account, you can connect to the Internet.
143 Exploring Y our Computer’ s Features An overview of using the Internet ❖ Internet chat roo ms A chat room is a W eb site that offers a pla ce where people with similar interests and ideas comm unicate in real-time, one-on- one or in groups, by typing messages which are instantly viewed by others on their computer screens.
144 Exploring Y our Computer’ s Features Explor ing audio feat ur es Exploring audio features Y ou can use your computer to record sounds using the com puter’ s internal microphone (av ailable on certain models) or an opti onal external microphone.
145 Exploring Y our Computer’ s Features Using the W eb Camera TECHNICAL NOTE: When using amplified speakers, use speak ers that require an external power source.
146 Exploring Y our Computer’ s Features Using an Expr essCard ® Using an ExpressCard ® The ExpressCard ® slot supports the use of Ex pressCard media. The slot also supports ho t swapping, which allo ws you to replace one ExpressCard with another while the computer is on.
147 Exploring Y our Computer’ s Features Using the Memory car d r eader 3 Gently press the ExpressCard inward to release it. The ExpressCard pops out slightly .
148 Exploring Y our Computer’ s Features Using the Memory car d r eader Inserting memory media The follo wing instructions appl y to all types of supported media devices. 1 T urn the media so that the cont acts (metal areas ) are face do wn. 2 Push the media into the ad apter until it locks in place.
149 Exploring Y our Computer’ s Features Using the eSA T A/USB combo port Do not remove memory media while data is being written or read. Even when the Windows ® message “copying...” disappears, writing to the media might still be in progress and your data could be destroyed.
150 Chapter 5 Utilities Y our computer includes sev eral utilities designed to help yo u to reconfigure your system to best meet your individual needs. T o gether , these allo w you to ascerta in certain system details, set additional options, or change default optio ns.
151 Utilities TOSHIB A Assist ❖ TOSHIB A Zooming Utilit y ❖ TOSHIB A Button Su pport ❖ TOSHIB A Accessibility ❖ Fingerprint Authentication Utilit y ❖ TOSHIB A eco Utility™ ❖ TOSHIB A Ser.
152 Utilities TOSHIB A Assist Connect The features av ailable in this category are: ❖ ConfigFree ® Connectivity Doctor ❖ Bluetooth ® Settings (Sample Image) T OSHIBA Assist window – Connect ta.
153 Utilities TOSHIB A Assist Secure The features av ailable in this category are: ❖ Supervisor password ❖ User password (Sample Image) T OSHIBA Assist window – Secur e tab.
154 Utilities TOSHIB A Assist Protect & Fix The features av ailable in this category are: ❖ TOSHIB A PC Diagnostic T ool Utility ❖ TOSHIB A HDD Protection Utility (Sample Image) T OSHIBA Assis.
155 Utilities TOSHIB A Assist Optimize The features av ailable in this category are: ❖ Mouse Utility ❖ TOSHIB A Accessibility ❖ TOSHIB A Zooming Utilit y ❖ TOSHIB A Button Su pport ❖ TOSHIB .
156 Utilities TOSHIB A Application Installer TOSHIBA Application Installer The T OSHIB A Application In staller allo ws you to re install the dri vers and applications that were originally bundled with your computer . T o reinstall dri vers and applications : 1 Click Start , All Pr ograms , My T oshiba , and then TO SH I BA Application Installer .
157 Utilities Setting passwor ds Setting passwords Setting a password lets you walk aw ay from your computer whi le providing additional protection for your files. When you set a password, you must enter the password before you can w ork on your computer again.
158 Utilities Setting passwor ds Using a supervisor password A supervisor password pre vents other users from changing hardware configuration options. Setting a supervisor password If you choose to se.
159 Utilities Setting passwor ds 6 Click OK . The supervisor password util ity dialog box appears. 7 Select Able to run HWSetup or Unable to run HWSetup and then Click OK .
160 Utilities Setting passwor ds T o register a password for the po wer- on password functions: 1 Click Start , All Programs , TOSH IBA , Utilities , and then TOSHIB A Assist . The TOSHIB A Assist windo w appears. 2 On the left side, click the Secure tab .
161 Utilities TOSHIB A F ace Recognition Utility TOSHIBA Face Recognition Utility Y our computer may come with the TOSHIB A Face Recognition utility . This utility provides another way to log on to y our computer . For high security purposes, TOSHIBA Face Re cognition is not a suitable substitute for Windows ® passwords.
162 Utilities TOSHIB A PC Dia gnostic T ool Utility TOSHIBA PC Diagnostic T ool Utility This utility can h elp diagnose pro blems with devices in your computer . Refer to the online Help documentatio n within the application for additional help. The TOSHIBA PC Diagnostic T ool u tility may show tests for features you do not have.
163 Utilities TOSHIB A HDD Pr otection Utility TOSHIBA HDD Protection Utility The TOSHIB A HDD Protection Utility controls your computer’ s hard disk dri ve (HDD) protection feature, which parks the HDD whene ver motion is detected on the computer .
164 Utilities Mouse Utility Mouse Utility The Mouse utility allows you to change your pointing device or mouse settings. T o access the Mouse utility: 1 Click Start , Contro l Panel , Hardware and Sound , and then under Devices and Printers , click Mouse , or click the Mouse icon in the Op timize tab of TOSHIB A Assist .
165 Utilities T O S H I BA H a rd w a re S e t u p TOSHIBA Hardware Setup TOSHIB A Hardware Setup is the T oshiba con figuration management tool av ailable through th e W indows ® operating system.
166 Utilities TO S H I B A H a rd w a re S e t u p ❖ Button Sett ing —Lets you set the conditions for th e po wer button and/or the other buttons. (Sample Image) TOSHIB A HWSetup screen - Button S.
167 Utilities T O S H I BA H a rd w a re S e t u p ❖ Illumination— T urns the panel LED lights on and off (av ailable on certain models) (Sample Image) TOSHIB A HWSetup screen - Illumination tab o.
168 Utilities USB Sleep and Char ge Utility USB Sleep and Charge Utility This utility displays w hether the “USB Sleep and Charge function” is enabled or disabled and shows the position of the USB port that supports the “USB Sleep and Charge function.
169 Utilities USB Sleep and Char ge Utility ❖ When “USB Sleep and Charge function” is set to Enabled, USB bus power (DC 5V) will be supplied to the compatible port even when the power of the computer is turned OFF . USB bus power (DC 5V) is similarly supplied to the external devices which are connected to the compatible ports.
170 Utilities USB Sleep and Char ge Utility Enabling USB Sleep and Charge This utility can b e used to enable or disable the “USB Sleep and Charge function” group . Check the check box fo r the group to enable the “USB Sleep and Charge function” for the USB port assigned to that group.
171 Utilities TOSHIB A Zooming Utility TOSHIBA Zooming Utility This utility allows you to select which applications will work with the zoom in/out hot ke ys (see “Zoom (Display resolu tion)” on page 228 ).
172 Utilities TOSHIB A Button Support TOSHIBA Button Support TOSHIB A Button Support allows you to customize the Mute and Media buttons . These buttons ar e located on the system control panel directly above the keyboard. T o access TOSHIB A Button Support: 1 Click the TOSHIB A Button Support icon in the Optimize tab of TOSHIB A Assist .
173 Utilities TOSHIB A Accessibili ty TOSHIBA Accessibility The TOSHIB A Accessibility utility allows you to use the Fn ke y to create a hot key combination wit h one of the function ke ys without pressing the two keys simultaneously as is usually required.
174 Utilities F ing erprint Authenticati on Utility Fingerprint Authentication Utility (A vailable on certain models) The fingerprint authentication utility (av ailable on certain models) can be used to replace the ke yboard-based user password authentication system when booting up.
175 Utilities F ing erprint Authent ication Utility The Fast User Switching feature of the W indo ws ® operating sy stem is also supported. If user A is logged on and the fingerprint utilit y verif ies the fingerprint of user B (who is already enrolled), the utility recognizes the fingerprint and switches th e users.
176 Utilities F ing erprint Authenticati on Utility Observe the follo wing to improve the fi ngerprin t recognition success rate. ❖ Enroll two or more fingers. ❖ Enroll additional fingers if r ecognition failure occurs often using enrolled fingers.
177 Utilities TOSHI BA eco Utility™ TOSHIBA eco Utility™ The T oshiba eco u tility™ monitors y our power sa vings from using the eco po wer plan by tracking real-time po wer consumption and accumulated savings o ver time.
178 Utilities TOSHIB A Service Station TOSHIBA Service Station The TOSHIB A Service Station helps you keep your ne w computer running at its best by notifying you when updated software, firmw are, documentation or othe r information is av ailable for your computer .
179 Utilities ConfigF r ee® The TOSHIB A PC Health Mo nitor software does n ot extend or modify T oshiba's obligatio ns under its standard limited warranty in any way .
180 Utilities ConfigF r ee® ❖ Click the Conf igFree icon in the notification area, and then click the desired utility . If your computer is not connected to a network, the ConfigFree icon in the notification area is displayed with an “X.
181 Utilities ConfigF r ee® Profile Settings The Prof ile Settings utility lets you save network settings in “profiles . ” ConfigFree ® prof iles are useful for easily switching network settings an d devices. Y ou can switch network settings simply by selecting the profile with the desired settings.
182 Utilities ConfigF r ee® 3 Click Open Settings . The ConfigFree Prof ile Settings windo w appears. (Sample Image) ConfigF ree Pr ofile Settings windo w 4 Click Add to start the Creat e Profile W i zard.
183 Chapter 6 If Somet hing G oes W r o ng Some problems you may encounter wh en using your computer are relativ ely easy to identify and solve. Others may require help fro m your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems b y yourself.
184 If Something Goes Wrong Pr oblems when you turn on the computer 2 Click the A pplications tab . If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End T ask .
185 If Something Goes Wrong Pr oblems when you turn on the computer The computer starts but when y ou pr ess a key nothing happens. V erify that the activ e program accep ts text input. T r y clicking your mouse on an area where you can type text and try typing again.
186 If Something Goes Wrong Pr oblems when you turn on the computer The computer displays the Non-System disk or disk error messag e. Make sure there is no diskette in the optional e xternal diskette driv e. If there is a diskette in th e dri ve, remo ve it and press an y key to continue.
187 If Something Goes Wrong The W indo ws ® operating system is not working 5 V erify that the AC adaptor is th e correct unit for your computer model.
188 If Something Goes Wrong The W indo ws ® operating system is not working Using Startup options to fix problems If the operating system fails to start properly , you may hav e to change your system’ s conf iguration or verify the startup procedure to fix the problem.
189 If Something Goes Wrong The W indo ws ® operating system is not working Internet problems My Internet connection is v ery slow . Many f actors contribute to the speed with which you can surf the Internet.
190 If Something Goes Wrong F ixing a pr oblem with De vice Manag er Fixing a problem with Device Manager Device Manager pro vides a way to check and change the configuration of a de vice. Changing the default settings using Device Manager can cause other conflicts that make one or more devices unusable.
191 If Something Goes Wrong Memory pr oblems Memory problems Incorrectly connected or faulty memory modules may cause errors that seem to be hardware or e ven software r elated. It is worthwhile checking for these firs t: 1 Click Start , and then click the Shut do wn button in the lo wer-right corner of the Start menu.
192 If Something Goes Wrong P ower and the batteries If the A C po wer light stil l does not come on, check that the wall outlet is working properly by plugging in a lamp or other appliance. The A C adaptor and power cord/c able work corr ectly , b ut the battery will not charge.
193 If Something Goes Wrong K e yboar d pr oblems Keyboard problems If, when you type, strange things happen or nothin g happens, the problem may be related to the keyboard itself. The keyboard pr oduces unexpected characters. A keypad o verlay may be on.
194 If Something Goes Wrong Display pr oblems If you are using an external monitor: ❖ Check that the monitor is turned on. ❖ Check that the monitor’ s po wer cord/cable is f irmly plugged into a working p ower outlet. ❖ Check that the cable connecting the external monitor to th e computer is fi rmly attached.
195 If Something Goes Wrong Disk or storag e drive pr oblems Small bright dots appear on yo ur TFT display when y ou turn on y our compu ter . Small bright dots ma y appear on your screen displa y when you turn on your computer .
196 If Something Goes Wrong Disk or storag e drive pr oblems 6 Y ou can choose one or both options: ❖ Automatically f ix f ile system erro rs ❖ Scan for and attempt reco very of bad sectors 7 Click Start . Error- checking tests and repairs the storage driv e.
197 If Something Goes Wrong Optical drive pr oblems (tray-type drive) Optical drive problems (tray-type drive) Y ou cannot access a disc in the dri ve. If the optical dri ve is an e xternal driv e, make sure that the driv e’ s cable is properly connected to the computer .
198 If Something Goes Wrong Sound system pr oblems The disc will not come out of the driv e when y ou click the eject button on the scr een. Press the b utton on the optical dri ve itself. For additional information see “Y ou press the disc eject button, b ut the dri ve tray does not slide out.
199 If Something Goes Wrong Expr essCar d ® pr oblems Resolving ExpressCard ® problems Here are some common problems and their solutions: The slot appears to be dead.
200 If Something Goes Wrong Printer pr oblems Hot swapping (r emoving one Expr essCard ® and inserting another without turning the computer off) fails .
201 If Something Goes Wrong Modem pr oblems Run the printer’ s self-test to check for any problem with the prin ter itself. Make sure you installed the proper printer dri vers as sho wn in “Setting up a printer” on page 87 or in the instructions that came with the printer .
202 If Something Goes Wrong W ireless networking pr oblems Wireless networking problems This section provides general troubleshooting tips for networking problems, specifically wireless (Wi-Fi ® ) networking. The terms and concepts used assume a bas ic understanding of networks, and may be for more advanced users.
203 If Something Goes Wrong D VD operating pr oblems T o enable or disable wireless communication, use the Hot Key Fn+F8 . For more information see “Hot Keys/TOSHIBA Cards” on page 214 . ❖ Use IPCONFIG to verify that the computer has a useful IP address—one other th an the priv ate address of 169.
204 If Something Goes Wrong Develop good computing habits 3 Use the D VD Player software that came with your computer to vie w DV D m o v i e s . 4 Clean the disc and try again.
205 If Something Goes Wrong Develop good computing habits On a regular basis, back up the inf ormation stored on y our internal sto rage drive. Use W indo ws ® to back up files, or the en tire computer , to an optical disc, or external hard disk.
206 If Something Goes Wrong Develop good computing habits Saving system configuration with restore points The System Restore feature of the Windo ws ® operating system quickly creates restore points—‘ snapshots’ of your W indows ® operating system configuration—and sav es them for later recall.
207 If Something Goes Wrong Develop good computing habits This list may contain restore points that you did not create. Restore points labeled System Checkpoint were automatically created by the Windows ® operating system. Other restore points may have been created automatically by applications when they were installed.
208 If Something Goes Wrong Develop good computing habits 4 Click Back up y our computer under the Syst em and Security heading. Follow the on-screen instructions to back u p your files. For more help , click Start , Help and Support , and search for “back up files.
209 If Something Goes Wrong Develop good computing habits 2 Create a restore point. 3 Install one item of hardware or software. 4 Restart the W indo ws ® operating system. 5 Use the new hardw are or software for a while, noting any new problems. Mak e sure that your critical applications (e- mail, business applications, etc.
210 If Something Goes Wrong If you need further assistance The eSA T A device is not recognized fr om Sleep or Hibernation mode. A connected eSA T A device may not be recognized if it is connected to the computer’ s eSA T A/USB combo port w hile the computer is in Sleep or Hibernation mod e.
211 If Something Goes Wrong Other T oshiba Internet W eb sites Contacting T oshiba If you still need help and suspect that the problem is hardware- related, T oshiba of fers a variety of resources to help you.
212 If Something Goes Wrong T oshiba’ s worldwide off ices T oshiba’ s worldwide offices A ustralia T oshiba (Australia) P ty . Limited 84-92 T alav era Road North Ryde NSW 2113 Sydney Australia Canada T oshiba Canada Ltd. 191 McNabb Street Markham, Ontario L3R - 8H2 Canada France T o shiba Systèmes (France) S.
213 If Something Goes Wrong T oshiba’ s worldwide of fices For more information on additio nal T osh iba worldwide locations, please visit: www .toshiba. co.jp/i ndex. htm . United States T o shiba America Information Systems, Inc. 9740 Irvine Boulev ard Irvine, California 92618 United States The Rest of Europe T oshiba Europe (I .
214 5.375 x 8.375 ver 2.3 Appendix A Hot Keys/TOSHIBA Cards Hot ke ys and TO SHIB A Cards provi de a quick way to modify selected system functions and to launch applications. There are two types of T OSHIB A Cards: Hot Ke y Cards and Application Cards.
215 Hot Keys /TOSHIBA Ca rds Hot K e y Car ds 5.375 x 8.375 ver 2.3 Using the Hot Key Cards The Hot Ke y Cards are normally hidden from view . The Cards appear when you press the Fn key . Hot keys are keys that, when pressed in combina tion with the Fn key , turn system functions on and off.
216 Hot Keys/TOSHIBA Cards Application Car ds 5.375 x 8.375 ver 2.3 Application Cards The Application Cards are used to launch these applications: TOSHIB A Assist For more information, refer to “TOSHIB A Assist” on page 151 . TOSHIB A HDD Protection utility For more information, refer to “TOSHIB A HDD Protection Utility” on page 16 3 .
217 Hot Keys /TOSHIBA Ca rds Application Cards 5.375 x 8.375 ver 2.3 Not all functions are supported on all models. Using the Application Cards T o launch an application using the Application Card s: 1 Press and hold the Fn ke y . The TOSHIB A Cards display at the top of the screen.
218 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Card Case The Card Case feature allo ws you to choose which cards appear in the Application Car d display (see “Using the Applicati on Cards” on page 217 ). T o use the Card Case: 1 Click Start , All Programs , TOSH IBA , Utilities , and then Settings for Flash Cards .
219 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Volume Mute or Fn + This TOSHIB A Card or hot ke y enables/disables volume mute on your computer . When volume mute is enabled, n o sound will com e from the speakers or headphones.
220 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Lock (Instant security) The Fn + F1 hot key function acti v ates instant security . The user logon screen will appear and a us er with a valid account will need to log back on to gain access to the computer .
221 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Power plan or Fn + This TOSHIB A Card or hot ke y displays the power plans and cycles through the power plans. The properties of each po wer plan, and the po wer plans that are displayed by this function, are set in the Power Options window .
222 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Sleep mode or Fn + This TOSHIB A Card or hot k e y places the computer into Sleep mode. For more information about Sleep mode, please see “Using and configuring Sleep mode” on page 94 .
223 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Hibernation mode or Fn + This TOSHIB A Card or hot k e y places the computer into Hibernatio n mode. If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernation mode” on page 92 .
224 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Output (Display switch) or Fn + This TOSHIB A Card or hot ke y cycles through the power - o n d i sp l a y o p t io n s (only the f irst option is av ailable when you do not have an external monitor attached) (the last option is available only if you are in Extend ed Display Mode).
225 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Display brightness Cycle through the display modes, th en select the desired mode. Not all functions are supported on all m odels. Some systems also support an additional Swap Image Display mode.
226 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling wireless devices or Fn + This TOSHIB A Card or hot ke y enables/disables th e optional wireless devices installed in your computer . The wireless modes are: ❖ Wi - F i ® enabled—Enables just the Wi-Fi ® module.
227 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling the T ouchPad™ or Fn + This TOSHIB A Card or hot ke y enables/disables th e T o uchPad. For more information on using the T ou chPad, see “Using the T o uchPad™” on page 78 .
228 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Zoom (Display resolution) or Fn + [ Space bar ] This TOSHIB A Card or hot key switches screen resolution.
229 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Keyboard hot key functions Fn + This hot ke y turns the curs or con trol overlay on and of f. Fn + This hot ke y turns the numer ic ov erlay on and off. Fn + This hot ke y turns the scroll lo ck feature on and off.
230 5.375 x 8.375 ver 2.3 Appendix B P o wer Cord/Cable C o nnector s Y our computer ships w ith the correct power su pply for the country of purchase. This appendix shows the shapes of the typical A C po wer cord/cable connectors fo r v arious parts of the world.
231 Glossar y TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer . Acronyms The follo wing acronyms may app ear in this user’ s guide.
232 Glossary DOS disk operating system DPI dots per inch DSTN dual supertwist nem atic DV D digital versatile (or video) disc DV D - R O M dig ital versatile (or video) disc read-only memory ECP enhan.
Glossary 233 RFI radio frequency interference RO M read-only memory RT C real-time clock SCSI small computer system interface SD Secure Digital SDRAM synchronous dynamic ran dom access memory SRAM sta.
234 Glossary application — A computer program that yo u use to perform tasks of a specific type. Applications includ e wo rd processors, spreadsheets, and database management systems. See also pro gram . B backup — A copy of a file, usually on a remov able disk, kept in case the original file is lost or damaged.
Glossary 235 CD — An individual compact disc. See also CD-R OM. CD-R OM (compact disc r ead-only memory) — A form of high- capacity storage that uses laser opt ics instead of magnetic means for reading data. See also CD . Compare DV D - RO M . central processing unit (CPU) — The chip that functions as the “brain” of the computer .
236 Glossary cursor — An on-screen symbol (usually a flas hing verti cal line) that indicates the position where charact ers will appear when you enter data. D default — The setting selected by a program when the user does not specify an alternati ve setting.
Glossary 237 document — Any file created with an application and, if sa ved to disk, gi ven a name by which it can be retrie ved. See also fil e . double-click — T o press and release the pointing device’ s primary button rapidly twice without moving the pointing device.
238 Glossary F fil e — A collect ion of related information, saved on disk with a unique name. A file may be a program, information used by a program, or a document. See also docum ent. f ile allocation table (F A T) — The section of a s t o r a g e d r ive that keeps track of the location of stored files.
Glossary 239 Hibern ation — A feature of many T oshiba computers that saves to the i n t e r n a l s t o r a g e d r iv e the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer w as turned off.
240 Glossary liquid crystal disp lay (LCD) — A type of display that uses a liquid substance between two transparent electrode panels. When an electric current passes through the electrodes, the molecules in the liquid form a crystalline pattern that polarizes the light passing through it.
Glossary 241 N network — A collection of computers a nd associated de vices that are connected by communications facilities. A network allows you to share data and peripheral de vices, su ch as printers, with other users and to exchange electronic mail.
242 Glossary Plug and Play — Generally , refers to the computer’ s ability to automatically configure itself to work with periph eral devices. When capitalized, refers to a sta ndard that, when followed by a device manufacturer , allo ws a computer to conf igure itself automatically to work with the device.
Glossary 243 res ta r t — Synonymous with reboot. T o reset the computer by reloading the operating system without tu rn ing the computer off. See also boot . RJ11 — A modular connector used o n most U.S. telephone syst ems and direct-connect modems.
244 Glossary system prompt — The symbol (in the MS-DOS ® operating system, generally a driv e letter follo wed by a “greater than” sign) indicating where users are to enter commands.
245 Index A A C adaptor 51 A C power (DC-IN) connecting adaptor 52 A C power light 51 Alt ke ys 101 Application Cards 216 audio fil e s 144 audio features 144 B backing up files 100 backlit keyboard 1.
246 Index character keys 101 charging the battery 53 checking device properties 190 communications network connection 139 set up 138 compact discs handling 112 inserting 112 compact discs (slot-type d.
247 Index error messages non-system disk or disk error 186 problem with display settings/ current settings not wor king with hardware 194 warning resume failure 185 Error-checking 195 eSA T A connecti.
248 Index CDs and D VDs 112 ExpressCards® 146 installation memory module 57 installing main battery 128 , 130 memory modules 57 mouse 86 Internet bookmarked site not found 189 connecting to 142 featu.
249 Index networking wireless 138 notification area 137 O optical disc handling 114 inserting (slot-type driv e) 111 inserting (tray-type drive) 113 positioning 113 optical driv e driv e in-use indica.
250 Index external monitor 19 4 fault y memory 191 high-pitched noise 19 8 Internet bookmarked site n ot found 189 Internet connection is slo w 189 keyboard not responding 185 keyboard produces unexpe.
251 Index recording 144 speakers using external 144 start button 137 starting a program 103 Search programs and f iles field 105 W indo ws® Explorer 104 W indows® Start menu 104 starting up the comp.
252 Index We b 141 We b C a m e r a using 145 We b s i t e s 211 Wi - F i ® wireless netw orking 138 W indo ws® Explorer 104 W indows® operating system Help and Support 18 9 problem solving 187 W i.
Een belangrijk punt na aankoop van elk apparaat Toshiba PSMLBU (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Toshiba PSMLBU heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Toshiba PSMLBU vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Toshiba PSMLBU leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Toshiba PSMLBU krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Toshiba PSMLBU bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Toshiba PSMLBU kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Toshiba PSMLBU . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
