Gebruiksaanwijzing /service van het product Bicycle Computer van de fabrikant Trek
Ga naar pagina of 40
This manual explains the installa- tion and use of the Trek Incite ACH and ACH Digital bicycle computers. Please read this manual carefully and save it for future reference.
Safety and general guidelines ......................................................... 1 F unctions ......................................................................................... 2 Installation ............
While riding your bicycle, do not stare at the computer for long periods of time (Figure 1). If you do not watch the road, you could hit an obstacle, which may cause you to lose control and fall.
.
.
.
Stem mount Handlebar mount Speed sensor Cadence sensor .
.
Check that the computer base cannot be rotated around the handlebar , and that the computer cannot slide backwards on the computer base (Figure 5). 1.
The wheel magnet must be aligned so that it passes across the sensor . As the magnet passes the sensor , it must be no further from the sensor than 1 to 3mm (1/32 to 1/8 inch).
These instructions are written for the cadence sensor , which goes on the frame’s lef t chainstay . The instructions apply equally to installing the ACH Digital cadence sensor or the wheel sensor on the fork- where there is no wire on the sensor .
5. With the computer in the computer base, check the alignment of the sensor and magnet by spinning the wheel and noting if the computer is displaying cadence (or for the wheel sensor , speed). If the computer shows cadence (RPM) or current speed, the sensor is reading the magnet.
T o monitor your pulse, or heart rate, you must be wearing the heart rate strap. The strap senses each contraction, or beat, of your heart.
Mode Set Scroll .
Mode Set Scroll Choose a method to R eSet the computer: • Push any button to wake the computer from shipping mode • Push the ReSet button (AC) on the back of the computer • Install a new battery The Wheel select icon appears with a tire size: 700-23 (Figure 14).
Mode Set Scroll This setting tells the computer which conversion to use: metric or SAE (“English”), which clock style to use (12-hour or 24-hour) and sets the time. 1. Cycle Scroll to your preferred setting: • MPH for miles • KPH for kilometers 2.
Mode Set Scroll 9. Cycle Scroll to the hour: • 1, 2, 3, etc. from 1A through 12P (for 12-hour clock) • 1, 2, 3, etc. through 24 (for 24-hour clock) 10. Push Set• to choose your setting. “00” flashes. 11. Cycle Scroll to the minute: • 00, 01, 02, 03, etc.
Mode Set Scroll 1. Cycle •Mode to SPEED. The P AIR? signal appears. 2. Make the wheel sensor send a signal (spin the bicycle wheel). 3. Place the computer within 3 feet (1 meter) of the sensor and Hold the Set• button.
Mode Set Scroll Y our computer stores data for two intervals- since last R eSet and since last ReStart. ReSet sets ALL data to zero. ReStart sets only the Trip data to zero.
Mode Set Scroll Once the computer is programmed and installed, it is very easy to use.
The Incite ACH computer is designed to be easy to install and maintain. However , computers occasionally have problems.
INCITE ACH .
1. R emove the computer from its base. 2. Identif y the battery cover , with its deep slot (a similar battery cover is found on the back, or skin-side, or the heart rate strap).
The ACH computer has many advanced functions and features. These include: Units .......................................................................................... 23 Clock .......
This setting tells the computer which conversion to use: metric or SAE (“English”). 1. Cycle •Mode to ODOMETER. 2. Cycle Scroll to TRP . 3. Hold Set• . “KMH” appears. 4. Cycle Scroll to your preferred setting: • MPH for miles • KPH for kilometers 5.
Mode Set Scroll 1. Cycle •Mode to CLOCK 2. Hold Set• “12” (Figure 14) flashes. 3. Cycle Scroll to your preferred clock setting: • 12 for 12-hour clock • 24 for 24-hour clock 4.
Mode Set Scroll In addition to the clock function, your computer also works like a stopwatch, keeping track of hundredths of seconds for up to 24 hours. At 24 hours, the stopwatch restarts at 0. 1.
Mode Set Scroll Y our com puter can read two dif ferent size s of whee ls on two diffe rent bik es, suc h as you r road bik e and mount ain bik e. Each whe el size can be cus tom set for gre ater accu racy . The tot als for each whee l are cumul ative (ODO METER TTL) .
Mode Set Scroll 1. Cycle •Mode to SPEED. 2. Hold Set• . The wheel selection icon appears. 3. Cycle Set• to a wheel: • Wheel 1 is a circle • Wheel 2 is a circle inside a semi-circle 4.
Mode Set Scroll T able 1 approximates the circumference of each tire size. Instead of using an approxima- tion, you can measure the actual circumfer- ence of your wheel.
Mode Set Scroll 1.
Mode Set Scroll In addition to the current speed which is always displayed, there are other SPEED features which you can access, shown below .
Mode Set Scroll By de fa ult , t he odo me te r on a ne w o r Re Set co mp ute r a lw ays st ar ts at ‘0 ’. How ev er , th e od om et er can be man ua ll y se t s o yo u d on’ t h av e to st ar t at ze ro . 1.
Mode Set Scroll Cadence is the number of complete pedal revolutions per minute, or RPM. In addition to Current RPM, the ACH also displays your average cadence (AVG) and fastest cadence (MAX).
Mode Set Scroll The ACH altimeter allows you to view your climbing total for a trip, and also calculates your total, like total distance. The display units correspond with the distance units set for the odometer: FT or M (Figure 27).
Mode Set Scroll 3. Hold Set• . The current elevation appears, and the + or - (above or below sea level) is flashing. 4. Cycle Scroll to your preferred value. 5. Push Set• to select. The first digit flashes. 6. R epeat steps 4 and 5 until all digits have been set.
Mode Set Scroll Grade describes the steepness of an incline. It is a function of altitude gain divided by the distance travelled, expressed as a percentage (Figure 28). F or example, if you gain 6 feet of elevation in 100 feet traveled (183cm / 47.
Mode Set Scroll The ACH computer also functions as a wireless heart rate monitor , and can display advanced heart rate data when the heart rate icon is displayed (Figure 29). These data are all erased when the Trip Data is erased.
Mode Set Scroll The heart rate zone can be set to give you an easy-to-read visual indicator of where your heart rate is. The Up and Down arrows indicate if your heart rate is above or below the zone (Figure 30).
Tr ek Bi cyc le Co rpo ra ti on war ra nt s ea ch new In ci te c om pu ter ag ai ns t de fe ct s in wo rk man sh ip and ma te ria ls .
Een belangrijk punt na aankoop van elk apparaat Trek Bicycle Computer (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Trek Bicycle Computer heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Trek Bicycle Computer vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Trek Bicycle Computer leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Trek Bicycle Computer krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Trek Bicycle Computer bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Trek Bicycle Computer kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Trek Bicycle Computer . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.