Gebruiksaanwijzing /service van het product 52052 van de fabrikant Troy-Bilt
Ga naar pagina of 28
GARDEN WAY INCORPORATED Owner’ s Manual T rimmer/ Mower • Safety • Assembly • Features/Controls • Operation • Maintenance • Parts List Models 52051– 4HP Std.
SECTION 1: SAFETY ...........................................1 General Operation ......................................................1 Slope Operation .........................................................2 Children...............................
1 1 Section Safety Under California law, and under the laws of several other states, you are not permitted to operate an internal combustion engine using hydrocarbon fuels on any forest covered, brush.
2 Section 1: Safety 20. Always wear approved safety gog- gles or safety glasses with side shields when operating equipment. The use of any powered machine can result in for- eign objects being thrown by high- speed rotating parts which can cause personal injury or property damage.
3 Section 1: Safety and debris shield. Make sure they are not bent, damaged, or loose. 10. Only use eighteen-inch long .130" or .155" diameter trimmer line. N ever use other lengths, diameters or material as trimmer line. 11. Trimmer line moves at high speed and can cut.
2 4 Section Assembly Introduction Carefully follow these assembly steps to correctly prepare your machine for use. It is recommended that you read this section in its entirety before begin- ning assembly. NOTE: If an assembly step applies only to certain models, those models are noted at the beginning of that step.
5 Section 2:Assembly STEP 3: Add Motor Oil A . The unit’s engine was shipped without motor oil which MUST BE ADDED before the engine is started. B. See the Engine Owner ’ s Manual you received for filling instructions and for the correct oil specifications for your engine.
6 3 Section D A N G E R KEEP HANDS and FEET AWAY W A R N IN G T H R O W N O B J E C T H A Z A R D Objects such as rocks, pebbles and small debris will be thrown violently by the cutting head, resulting in significant hazard to eyes and exposed body parts! Keep children, pets and bystanders 50 feet away from machine while operating.
7 4 Section Operation NOTE: All references to left, right, front and rear of the machine are determined by standing in the operator ’ s position. PRE-ST ART CHECKLIST A. Review Section 1: Safety and also Section 3: Features and Controls. B. Check equipment for loose or miss- ing hardware.
8 Section 4: Operation ADJUST LINE CUTTING HEIGHT Cutting Height Adjustment The cutting height of the trimmer line adjusts from 1-1/2"-to-4-1/2" high in infinite increments. The cutting height has been factory-set at one of the higher settings – we recommend that you start at this higher setting and make adjustments as needed.
9 Section 4: Operation Once you have read and understood the sections in this Manual on “ Safety, ” “ Features and Controls, ” “ Assembly, ” and “ Operation, ” you are ready to start and operate your trimmer/mower. Checklist Before Starting: 1.
10 T rim When Wet or Dry Grass and most other materials are most efficiently trimmed when dry. But the trimmer/mower will do a fine job even with damp or wet materials. When conditions are moist or damp, be sure to clean debris off the machine regularly to keep cutting efficiency high.
11 5 Section Maintenance/Repairs NOTE: All references to left, right, front and rear of the machine are determined by standing behind the handlebars and facing the direction of forward travel.
12 ADJUSTING TRIMMER HEAD ENGAGEMENT A. To test for correct belt tension, en- gage the control bail while the engine is running. If correct, the trimmer head will rotate when the control bail is pulled back fully against the handlebar.
13 INSPECTING / REPLACING THE DRIVE BEL T The drive belt can be inspected or re- placed from beneath the machine deck. The belt should not require inspection for many hours of operation. If re- placement becomes necessary, follow the instructions given here.
14 Section 5: Maintenance/Repairs BEL T PERFORMANCE TROUBLESHOOTING Sub-par belt performance (noise, overheating, cracking, etc.), can be caused by several situations. Follow the steps below to correct belt perfor- mance problems. Also use these checks after installing a new belt.
15 Section 5: Maintenance/Repairs CHANGING TRIMMER/ MOWER LINES Replace the trimmer lines when they wear to the point that trimming and mowing projects take too long and re- quire too much movement. A good rule of thumb is to change the lines when they reach half their original length.
16 CLEANING THE ENGINE FOAM DEBRIS FIL TER It is extremely important to keep the foam debris filter (A, Figure 5-14) free of dirt and dust so the engine can run as efficiently and as cool as possible. Clean the foam debris filter every time you refuel (also remove all debris from around the fuel fill cap).
17 BA TTERY RECHARGING Prior to and after coming out of storage, recharging the battery is recommended. The engine must be stopped and the area in which recharging will take place must be dry. A. Connect the battery charger shipped to you to the trimmer/ mower wire har- ness (A, Figure 5-15).
18 Section 5: Maintenance/Repairs TROUBLESHOOTING Before performing any of the corrections in this Troubleshooting Chart, refer to the appropriate information contained in this Manual for the correct safety precautions and operating or maintenance procedures.
19 Parts Ordering Information If you need service or parts: For service assistance or parts, contact your local authorized dealer or the factory. Your local dealer or the factory service department will need to know the model/serial numbers of the unit to provide the most efficient service.
20 T rimmer/Mower Parts List ENGINE, DECK, COVERS AND GUARDS, BATTERY 1 3 12 23 22 32 28 28 25 25 33 35, 36 34 26 37 26 23 29 30 41 40 40 41 31 27 23 4 24 37 24 43 42 37 5 6 9 2 19 7 8 39 17 18 14, 38.
21 Models 52051 and 52052 1 1916993 Deck with decals ....................................... 1 2 1904511 Decal-Hot Surface ..................................... 1 3 1904403 Decal-Warning/Thrown Objects ................ 1 4 1739687 Decal-Danger Feet/Hands .
22 T rimmer/Mower Parts List 1 10 19 22 23 24 25 19 5 12 14 14 17 20 13 4 7 7 2 9 HANDLEBAR ASSEMBLY.
23 Models 52051 and 52052 1 1915963 Upper Handlebar w/decal ....................... 1 2 1915889 Bail Decal ............................................... 1 3 ---- Ref. No. Not Used 4 1915270001 Bail ...................................................
24 T rimmer/Mower Parts List 1 1910823 Wheel - 6 spoke ..................................... 2 2 1915823 Wheel Stud ............................................. 2 3 1915824 Wheel Mounting Bracket ........................ 2 5 1733398 Top Lock Nut, 3/8-16 .
25 Models 52051 and 52052 Ref. # Part # Description Qty. TRIM HEAD ASSEMBLY 1 1910863 Shoulder Washer .................................... 1 2 1910861 Spindle Head .......................................... 1 3 1915857 Trimmer Head ...................
CUSTOMER SERVICE INFORMA TION Owner Registration Card Please fill out and mail the enclosed owner registration card. The purpose of this card is to register each unit at the factory in order to keep the owner informed with informational bulletins and safety literature.
Een belangrijk punt na aankoop van elk apparaat Troy-Bilt 52052 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Troy-Bilt 52052 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Troy-Bilt 52052 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Troy-Bilt 52052 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Troy-Bilt 52052 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Troy-Bilt 52052 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Troy-Bilt 52052 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Troy-Bilt 52052 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
