Gebruiksaanwijzing /service van het product UBCD996T van de fabrikant Uniden
Ga naar pagina of 148
Owner's Manual OWNER'S MANU AL UBCD996T.
2 Precautions Before you use this scanner , please read and observe the following. Be sure to use only a monaural earphone or 32 stereo headset. Use of an incorrect earphone or stereo headset might be potentially hazardous to your hearing. The output of the phone jack is monaural, but you will hear it in both headphones of a stereo headset.
Power Related Issues Import ant: Notes: [VOL] /Power Switch ON OFF ON T o prevent memory from being corrupted, do not unplug the AC adapter during the time the memory is accessed for programming or auto store. If when you connect the AC adapter the is , the scanner may not power on.
4 T able of Content s Precautions ...................................................................................................................................2 Introduction .......................................................................
5 Included With Y our Scanner ......................................................................................................30 Setting Up Y our Scanner ...........................................................................................
6 Setting the GPS Format .............................................................................................................57 Setting the Position Format ......................................................................................
7 Searching and Storing ................................................................................................................92 Using the Close Call Feature ...................................................................................
8 Care and Maintenance ..............................................................................................................125 T roubleshooting .................................................................................................
9 This page is intentionally blank..
10 This page is intentionally blank..
Introduction Y our UBCD996T scanner is a st ate-of-the-art scanner radio with T runk T racker IV™ and automatic scanning capabilities. Y ou can store in the dynamic memory conventional frequencies such as police, fire/emergency , marine, air , amateur , and other communications.
Feature Highlight s General Close Call™ RF Capture T echnology Close Call Do-Not-Disturb Close Call T emporary Store Dynamically Allocated Channel Memory Preprogrammed Systems 100 Quick Keys 9 Servi.
Fire T one-Out St andby Broadcast Screen Custom Screen Scan/Search Delay Attenuator Repeater Reverse Channel Alert Memory Check Search with Scan Operation Custom Alert s Automatic Channel Step Frequency Step T ext T agging Dat a Skip Duplicate Frequency Alert — Lets you set the scanner to alert you if a two-tone sequential page is transmitted.
Memory Backup T emporary Lockout St artup Configuration Single-Handed Function Control Operation Record Out Jack Display and Keyp ad Backlight V ehicle Power Connection (Orange Wire) T runk T racker I.
Distance to a POI, Direction to a POI, T ime to a POI, S peed, Position, and more. — Lets you quickly select and search the scanner’s preprogrammed frequencies. — Lets you program up to 10 custom search ranges. Y ou can search any of these ranges simultaneously .
Memory Storage Limit s * depending on the number of TGID in the system. 16.
Search Lockout Limit s About This Manual The screen displays used in this manual are representations of what might appear when you use your scanner . Since what you see depends on the frequencies and .
18 How the Scanner ’s Controls Are Represented in This Manual Entering T ext Within A Menu Option T o help navigate the scanner ’s menus, the steps shown in this manual show the displays you see and the keys you press or control you operate to get a desired result.
A Short User ’ s Guide to Assist the First-Time Scanner Enthusiast and Glossary Welcome to the family of Uniden scanner users. Y ou have just unpacked your Uniden UBCD996T scanner . Y ou are anxious to scan and hear something so you rotate the control and wait a moment as the opening Message and Copyright screens confirm the model information.
be overwhelmed. Begin by choosing the T alkgroups of interest to you. Begin by transferring the data from the Radio Reference website to the worksheet s you obtain from the Uniden website and from there, to the scanner .
Underst anding Scanning and the UBCD996T This section provides you with additional background on how scanning works and how your scanner provides that feature. Y ou don’t really need to know all of this to use your scanner , but some further background knowledge will help you get the most from your UBCD996T .
What is Scanning? What is Searching? What is CTCSS/DCS? Unlike standard AM or FM radio stations, most two-way communications do not transmit continuously . Y our UBCD996T scans programmed channels until it finds an active frequency , then stops on that frequency and remains on that channel as long as the transmission continues.
Conventional Scanning Simplex Operation Conventional scanning is a relatively simple concept. Each group of users in a conventional system is assigned a single frequency (for simplex systems) or two frequencies (for repeater systems). Any time one of them transmits, their transmission always goes out on the same frequency .
Repeater Operation What is T runk T racking? Repeater systems use two frequencies: one transmits from the radio to a central repeater; the other transmits from the repeater to other radios in the system.
T runked Scanning T ypes of T runking Systems While conventional scanning worked great while there were only a few groups wanting to use the frequencies, with the advent of smaller , lower-cost radios more and more agencies and businesses wanted to take advant age of the utility of 2-way radio.
to the assigned voice channel and the user can begin speaking. This all typically takes place in about a second...the person transmitting hears a beep from their radio when the channel is assigned.
agency is then subdivided up to 16 times to provide fleet identification, and then 8 more times to identify subfleets. For example, the complete AFS for the Police Department West District’ s dispatch channel might be 01-062.
28 St artup Configuration Multi-Site T runking Setup/Operation The S tartup Configuration option lets you quickly and automatically lock and unlock systems based on your desired configuration. Simply hold down a number button while powering on the scanner or while the opening screens are displayed.
29 I-Call (Motorola/EDACS) Where T o Get More Information I-calls are direct unit-to-unit transmissions that are not heard by other system users. Y our UBCD996T can receive I-call transmissions. See “Setting I-Call (Motorola and EDACS Systems Only)” on Page 72 for more information about monitoring I-call transmissions.
30 Included With Y our Scanner If any of these items are missing or damaged, immediately cont act your place of purchase. Owner's Manual OWNER'S MANUAL UBCD996T UBCD996T (P/N AAD-996S).
31 Setting Up Y our Scanner These guidelines will help you install and set up your new scanner: The UBCD996T can be placed on a convenient surface in your home as a base station, and connected to a st andard outlet that supplies 240V AC, 50Hz.
32 T o secure the radio, by means of the mounting bracket, to a surface, follow the steps below: 1. Attach the four protective rubber feet to the mounting bracket when you casually use the scanner on a flat surface.
33 W ARNING! BNC Antenna Connector REC All Channel Marked Channel Use only the Uniden-supplied AC adapter with this scanner . Insert the connector of the supplied indoor telescoping antenna to the and apply moderate pressure to secure it.
Important: A VOID AIRBAG DEPLOYMENT ZONES. Ignoring this inst allation concern may result in bodily harm and the inability of the airbag to perform properly . 1. Using appropriate screws or other hardware, secure the bracket. 2. Insert the scanner and insert the bracket knobs to lock the scanner in position.
35 1. Remove the bracket if previously attached. 2. Remove the four Philips screws on the rear that secure the outer metal case and pull off the case with care. 3. Install the DIN sleeve into the opening in your dashboard, lip facing out. 4. Push out the top and bottom tabs to hold the sleeve firmly in place.
36 Removing the Scanner from the DIN-E Sleeve Mounting Using ISO T echnique If you plan to connect other devices or wires to the radio, such as a GPS unit, at a later time, you should plan to remove the scanner from the DIN-E sleeve. This is easily done using the provided Removal Keys.
37 Once the original radio is removed from the vehicle dash and the fit of the scanner is correct, be sure to connect all the power , audio, antenna, and any other cables or wires, to the scanner before the scanner is secured.
38 W ARNING! Ext. Sp. Jack W ARNING! Never connect anything other than the recommended amplified extension speaker to the scanner ’s head phone jack. Damage to the scanner might occur . In a noisy area, an optional amplified extension speaker , positioned in the right place, might provide more comfortable listening.
39 Controls, Keys, and Functions Each of the knobs and keys on the UBCD996T produce several dif ferent actions depending upon how you activate them. Y ou can, for example, rotate the knobs as well as press them to achieve a different action. Some keys provide one action when briefly pressed while pressing and holding a key gives a different result.
40 + Press.
41 [SRVC] All Opens Service Search Select menu Press.
42.
43 SRVC SRVC.
44 A Look At The Display The display has indicators that show the scanner ’s current operating st atus. The display information helps you underst and how your scanner operates. The LCD screens shown here are only a few of many that you will see while in different modes.
45 Operation T urning On the Scanner and Setting the Squelch St artup Key Operation T o turn the scanner on, rotate clockwise. T urn the knob to a comfortable sound level. Rotate the squelch control clockwise until you either hear a broadcast or noise just stops.
46 [MENU] [0] [9] [.No] [SCAN/SEARCH] Notes: Select a Custom Range Assign all the systems/sites that you want to scan at the same time. Y ou can use one key to for each. In additional, you can assign the same startup key to the next system or site so that system or site is unlocked at power up.
47 Selecting Systems to Scan Selecting System Channel Group s T o select systems to scan, press then press the quick key assigned to the system or systems you want to scan. For quick keys , press the quick key’s number . For quick keys 10-99, press then press the quick key’s 2-digit number .
48 Locking/Unlocking Systems Locking/Unlocking Channels ID Scan/ID Search Mode Follow these steps to lock out a system so that it does not scan even if it s quick key is selected. 1. T ap the Scroll Control to switch to the Function Mode then rotate the control to select the desired system.
49 ! ID Search — the scanner stops on any unlocked t alk group that becomes active. T o toggle between ID Scan and ID Search, press then press while the scanner is scanning the system. If the scanner does not scan the system long enough for you to easily do this, press and rotate the Scroll Control to select the changed system.
50 If you enter a frequency then press , the scanner stores it in the group in a system called . These group s are created if they do not exist. Then, the scanner prompt s you to save other channel settings. If you enter a talk group ID then press , the scanner stores it into a channel group named in the current system.
51 T oggling the Display Mode T o change the display so the channel and frequency or T alk Group ID appear instead of extended channel information, hold on any channel then press . The scanner displays . T o return to Mode 1, press Mode1 indicates the under the Channel Name.
52 Optimizing P25 Performance Y ou can optimize the scanner ’s performance with digit al APCO 25 systems. Follow these steps for each system where you can hear APCO 25 traffic. These steps work only when you can clearly receive the system. If you are in a weak-signal area or receive interference, these steps will not work.
53 ! ! The next to last line on the display now shows the digital error rate and the AUTO decode threshold start level (0-20). The last line on the display shows the decode threshold levels for the system. Allow the scanner to monitor channel activity for several minutes.
54 Using the Menu The UBCD996T incorporates an ef fective menu system that lets you make all the necessary setting options required to program the scanner and effectively use the many features. T o use the menu, press . Y ou immediately see the screen display the menu title at the top and three of ten menu options beneath.
55 Programming General Settings This section covers your scanners general settings. The LCD has a backlight that can be set to green or red with three levels of intensity for each color plus . T o make your selection, press . Each time you press the control, the backlight cycles in the following order .
56 - Polarity Manual High Middle Low Off Settings Set Backlight Set Color Settings Adjust Key Beep Auto Level 1 15 Off Settings Set Audio AGC Analog On Off — If the headlight wire is connected to vehicle ground when the headlights are on, pick this setting.
57 Digital On Off On Off Settings Set Upside-down On Settings Adjust Contrast Level 1 Level 15 Settings Set GPS Format Settings Set GPS Format Set Pos Format to select either or specifically for receiving digital channels. — Press to select. — Press to select.
58 Setting the Time Format Setting the Time Zone Setting the Distance Units [MENU] [MENU] [MENU] [MENU] This setting controls the format used for displaying the time on the GPS data screens. — the scanner displays time in 12-hour format using am for mornings and pm for evening times.
59 your PC (default 1 15000 bps) and the back port to the speed used to communicate with an attached GPS (default 4800 bp s). Note that the back port is male. Y ou may need a gender changer and a null modem adapter to use a typical DB9 serial cable from the rear port.
60 2. While pressing , , and at the same time, turn on power . At that point anything you have programmed is gone. Y ou are given a last opportunity to keep the factory programmed data when you see th.
61 T o clone (transfer) data directly from one UBCD996T scanner to another UBCD996T scanner , you must first connect the scanners to each other using the included connection cables and a DB9 null modem adapter and for the rear port, a DB9 gender changer (neither included), available at most computer stores.
62 Programming Y our Scanner T o get the most out of your UBCD996T you can organize frequencies into programmed radio systems. 1. Plan the system. 2. Program the system into your scanner according to the plan you prepared in S tep 1. Y ou can store up to 6000 channels in up to 500 systems.
63.
64.
65.
66 Programming Conventional Systems [MENU] The scanner creates an empty conventional system with a default name of . Note that “n” is a number that increments as you add new systems. The on the right side of the display indicates that this is a conventional system.
67 Programming T runked Radio Systems Programming System Settings [MENU] Then, select the system type: — Motorola T ype I systems — Motorola T ype II and APCO 25 systems — EDACS Wide and Narrow .
68 Throughout the balance of this manual you will see a designation such as on the same line as a heading. This means that the section, in this example, applies otorola, DACS, TR, onventional and EDACS CA T systems. In order for trunk tracking to work properly , you have to specify the correct system type when you create the system.
69 After selecting this option, select any number from 0-99 to assign the system to a quick key or press to assign the system to no quick key , then press . Access single-digit system/site Quick Keys by pressing the single digit on the k keypad during scanning.
70 Setting the System Hold Time C Setting ID Scan/ID Search MEL Setting Channel Delay Time MELCS Setting Data Skip C [MENU] [MENU] [MENU] [1] [5] Notes: [MENU] Select a conventional system Set how long the scanner will remain scanning on this system before moving to the next system (up to 255 seconds).
71 Setting Location Information C Setting the Fleet Map M (T ype I Only) [MENU] [MENU] Note: Select a Conventional system This setting control whether the system is automatically enabled and disabled when you connect a GPS to the scanner . Set Latitude — Enter the system’s latitude using the format you selected in the system settings.
Setting the Status Bit M Setting End Code Operation M Setting I-Call Operation ME [MENU] Note: [MENU] Note: [MENU] Select a Motorola T ype I or II system — the scanner rounds all received ID’s down to the next interval of 16. The default setting is .
73 Off Off Only Program System Edit Sys Option Emergency Alert Off Alert 1 9 Off Set Level Auto Level 1 15 Program System Edit Sys Option EDCS ID Format AFS Format Decimal Format — the scanner ignores I-calls. The default setting is . — the scanner only tracks I-calls and ignores other radio traffic on the system.
74 Setting the System Record Option MELCS Reviewing ID Search L ockouts MEL Clearing All Lock ed Out ID’s MEL [MENU] REC REC REC Note for systems [MENU] [E ] [MENU] Select a system This setting controls how the scanner handles the record option for channels in the system.
75 Adjust the P25 Decode Threshold C Editing Sites MESL Editing Channel Groups MECL [MENU] Note: Select a conventional system This setting determines some system-specific parameters for digit al channels. In most cases, setting this to provides the best performance.
76 Copying Systems MECSL Deleting Systems MECSL Setting the Site Name ME Occasionally you might want to copy and rename a system to highlight one group over another . One system might be called City - Fire and the same system City - PD with adjustments to dat a within.
77 MS1: Motorola 800 MHz Type I Standard MS2: Motorola 800 MHz Type II Standard MP1: Motorola 800 MHz Type I Splinter MP2: Motorola 800 MHz Type II Splinter P25: APCO 25 (all bands) M92: Motorola 900 .
78 Notes: [.No] [MENU] Notes: [MENU] [.No] [MENU] ! ! ! ! ! ! Access single-digit system/site Quick Keys by pressing the single digit on the keypad during scanning. Access two-digit system Quick Keys by pressing then both digits. Y ou can assign as many systems to the same quick key as you want.
79 Note: [MENU] Note: + [7] [MENU] [MENU] If you select Control Channel Only mode (see “Setting Control-Channel Only (Motorola Systems Only)” on Page 81), you only need to enter the frequency(s) that can be assigned as the control channel. Most frequency lists usually indicate which of the frequencies are the control channel frequencies.
80 Q Q Edit Site g Select a site Select from the following choices — the system is scanned when its quick key is enabled. — the system is locked for this session.
81 Q Q Q Q Q Q Q Q Q Select a VHF or UHF site Y ou can enter up to 3 band plans. Select the plan to enter or edit, then follow the prompts to enter the Base Frequency , Channel S tep, and Channel Offset for the site. The UBCD996T includes two operation modes for P25 systems: explicit mode and implicit mode channel assignment.
On Off On Program System Edit Site (current) Set LocationInfo Set Latitude Set Longitude Set Range Set GPS Enable Program System Edit Site (current) Adjust P25 Level Auto — Y ou only need to enter control channel frequencies. — Y ou must enter all voice and control channel frequencies.
83 Auto Manual Manual Default Program System Edit Site Delete Site Confirm Delete? Yes=”E” / No= ”.” Important: Program System Edit Group New Group Group n.
84 Follow these steps to enter/edit the group name. 1. The current name displays with the first character of the name highlighted. 2. Rotate the to select a new first letter . Press to move one character to the right. Repeat the action to change the character .
85 This setting determines whether the scanner will scan this group of channels. Select your setting, then press . — the group is not scanned. — the group is not scanned for this session. The L/O is cancelled when you cycle power . — the group is scanned.
86 Q Select the channel Follow these steps to enter/edit the channel name. 1. The current name displays with the first character of the name highlighted. 2. Rot ate the to select a new first letter . 3. Press to move one character to the right. 4. Repeat the action to change the character .
87 Qg g g g gg Qg Q Qg Qg Qg g g gg g g g g g Select a channel group Select the channel T o edit the T alk Group ID, enter the T alk Group ID you want using the number keys. Then press . For each channel, you can select the audio type that the channel receives.
88 Qg Qg gg Qg Qg Qg Qg Qg Qg At this point you can scroll to CTCSS or DCS and select the subaudible frequency in the CTCSS range or the DCS code. — any signal opens squelch. The default setting is . — the scanner searches for and displays any CTCSS or DCS tone that accompanies the transmission.
89 Auto Auto AM FM NFM WFM WFM Auto Program System Edit Group Edit Channel Set Attenuator On Off Off Program System Edit Group Edit Channel Set Priority — the scanner uses the default modulation for the channel. The default setting is . — the scanner uses AM (amplitude modulation) for the channel.
90 This setting controls whether the scanner treats the channel as a priority channel while scanning. Select or , then press . — when you turn on the Priority feature, the channel will be scanned every 2 seconds. — the channel will not be treated with priority .
91 Setting Lockout MESL Copying a Channel MESL Deleting a Channel MESL [MENU] [MENU] [MENU] [MENU] Select a system Select a channel Select a channel group — the channel is scanned when its quick key is enabled. — the channel is locked for this session.
92 Searching and S toring Service Search Service Search lets you select and search the scanner’s preprogrammed search ranges. During service search, the scanner searches starting with the lowest frequency in the search range you select to the highest frequency in the range.
93 T o lock out a frequency found while searching, press one time to temporarily lock it out ( appears) or twice to permanently lock it out ( appears). If all frequencies in the search range you selected are locked out, appears and the scanner does not search the range.
94 The scanner start s custom search of the custom search range you selected, stopping on any transmission it finds and displaying the frequency . T urn the Scroll Control to change the search direction. An arrow appears, showing the current search direction.
95 Set Delay Time Set Modulation Set Attenuator Set Data Skip Set Step Set C-Ch Only Set Record On Adjust P25 Level Search with Scan Set Quick Key Set Startup Key Set Lockout Set Hold Time — lets you set the amount of time the scanner will delay before continuing to search after a transmission ends.
96 In addition to this scan you can search any of the preprogrammed service or custom search ranges. While scanning, press . Rotate the until you reach the desired service or custom search range. Press to unlock it. Y ou can also assign a System Quick Key to the search to make it easy to quickly enable/disable the search range for search and scan.
97 Set Attenuator Set Record Assigning a Search Range to a Search Key Saving a Found Channel (Quick Save) Qg Qg gQ g Qg Qg Qg to select to choose an attenuation for all frequencies in the range. — the frequencies are attenuated. — the frequencies are not attenuated.
98 Auto Search and Store Y our scanner ’s Auto S tore feature lets you search for new frequencies in custom search ranges or within a service search range on a conventional system, or new talk group ID’ s on a trunked system.
99 Trunked Search and S tore Y ou can store talk group ID’ s into the system you selected in “Selecting a System”. Otherwise, the scanner stores talk group ID’ s in a new group it creates.
100 Using the Close Call Feature Y our scanner ’s Close Call™ feature let s you set the scanner so it detects, displays the frequency of, and lets you hear a nearby strong radio transmission.
101 Call mode and stores any Close Call hits, up to the maximum you specified in the setting. If the scanner stores more hits than this setting, it stop s auto store operation. T urn the Scroll Control to display an option, then press . — Lets you select the Close Call mode.
102 Set CC Bands VHF Low 1 VHF Low 2 Air Band VHF High 1 VHF High 2 UHF 800MHz+ On Off — Lets you select the Close Call band settings. Y ou can turn the following bands on or off. (25.0000 - 53.9800 MHz) — (54.0000 - 107.9000 MHz) — (108.0000 - 136.
103 resuming scan. This let s you continue to hear transmissions detected with the Close Call feature, even after you are no longer close enough to receive it as a Close Call hit. Follow these steps to set up the option. or or Set the available option as you would for other menu items.
104 Search and Close Call Options The settings in this section affect custom searches, service searches, and Close Call operation. The following t able shows what options are available for various sea.
105 Unlocking All Frequencies Reviewing Locked-Out Frequencies Searching for Subaudible T ones Screening Out Broadcast Sources [MENU] [MENU] [MENU] Note: [MENU] The scanner prompts you to confirm deletion. T o confirm and delete all locked-out frequencies, press .
106 This setting determines whether the scanner automatically ignores transmissions found during Custom Search, Quick Search, or Close Call operation that are on common broadcasts, p aging systems, and other annoyance radio sources. Broadcast screening does not work in All service search ranges.
107 Qg Qg gQ g Qg gQ g Qg or This feature sets whether the scanner tries to tune to a repeater output frequency during Custom Search, Quick Search, or Close Call operation when it detects a transmission on a repeater input frequency .
108 AM FM NFM WFM WFM Srch/CloCall Opt Set Attenuator On Off Srch/CloCall Opt Set Data Skip On Off Off — the scanner uses AM (amplitude modulation) for the frequency band. — the scanner uses FM (frequency modulation) for the frequency band. — the scanner uses narrowband FM for the frequency band.
109 Setting the Delay Time Setting the Search Frequency S tep Setting Record Adjust P25 Level [MENU] [MENU] [MENU] RECORD OUT This setting determines how long the scanner waits af ter a transmission ends before resuming Quick Search or Close Call operation.
11 0 [MENU] [PRI] [MENU] — The automatic adjust feature is enabled. — you can set the threshold manuals depending on your circumstances. — sets the factory default value. If you activate a Priority Scan while scanning, the radio interrupts it s scan every two seconds to check the priority channel (P-Ch).
111 This page is intentionally blank..
11 2 This page is intentionally blank..
11 3 This page is intentionally blank..
11 4 Fire T one-Out Y our scanner can be set to respond to fire tone-outs, a system comprised of standardized two-tone sequential p aging, short one-tone paging, and long group tone paging.
11 5 ! ! ! ! ! ! ! Edit Frequency Set Modulation Auto FM NFM Set Attenuation On Off Set Tone Edit Tone A Edit Tone B Set Delay Time 1-5 sec Infinite Off Set Alert Alert 1 9 Off — Notes: [HOLD/RESUME] Enter the desired frequency that the scanner should monitor for the tone-out.
11 6 After you select an alert p attern, the scanner prompts for the alert level for a received alert. Level options 1 to 15 sets a fixed audio level independent of the main volume setting. uses the main volume setting for the alerts. The scanner can check multiple tone combination pages for channels whose settings are the same.
11 7 Location-Based (GPS) Scanning The UBCD996T can make use of dat a transmitted from an attached GPS unit that lets the radio automatically enable and disable systems based on the geographic informa.
11 8 current location. If you have a lot of data programmed, it might t ake the scanner a couple of minutes to complete the process. Once the scanner completes the initial GPS review , if you move into or out of an area covered by a radio site, the scanner beeps and displays the name of the system and whether it is being locked or unlocked.
11 9 Non-Radio Location Based GPS Features When connected to a GPS, you can program specific location information which will trigger an alert from the scanner . The following geographically based values are typical of the use you might find valuable while traveling.
120 By pressing & holding , you can select a location type and store current location data. The following table shows the attributes available for each category . Note that some options are different for a specific location type. Refer to the information that follows to set those specific attributes.
121 Qg Qg Qg gg g g g g Qg g Q Q Q Q Set Type Set LocationInfo Set Lockout Lockout Temporary L/O Program Location Dangerous Xing Delete Location Confirm Delete? Yes=”E” / No=”.
122 Qg Qg Qg Qg Input how far away the alert sounds for the site (only available for POI’s) The Alert T one is fixed. select from 15 sound levels, plus Auto and Off. As you rotate the the Alert tone is played louder and louder . Press to select a volume level.
123 GPS Review Location Mode If you have programmed data for a Point of Interest, Dangerous Crossing, and a Dangerous Road, you can review each set on a screen dedicated to showing just that data. Press in GPS Mode. The most recent stored location is displayed.
124 [.No] [E ] [SCAN/SEARCH] [HOLD/RESUME] — returns to GPS Mode. — lets you edit a location det ails — enter scan mode. — enter Scan Hold mode — enter Function Mode. — select a programmed location from all stored locations. The location data is stored in the order POI, Dangerous Xing, and Dangerous Road.
125 Care and Maintenance General Use Location Cleaning Birdies T urn the scanner off before disconnecting the power . If memory is lost, simply reprogram each channel. Always press each button firmly until you hear the entry tone for that key entry . Do not use the scanner in high-moisture environments such as the kitchen or bathroom.
126 T roubleshooting From time to time, Uniden might update the UBCD996T’s firmware to change the scanner ’s performance or incorporate new features. These updates can be applied by you using the supplied PC cable and the software that we will provide.
127.
128 If you still cannot get satisfactory results while using your scanner or if you want additional information, please call or write the Uniden Parts and Service Division. The address and contact number are listed in the W arranty at the end of this manual.
129 S pecifications Certificated accordance with FCC Rules and Regulations Part 15 Subpart C as of date of manufacture. Dynamic Allocation Capacity Systems : 500 max Groups : 20 per system Site : 1000.
Attenuation : 20dB nominal Scan Rate : 100 channels per second (Conventional mode) max Search Rate : 300 steps per second (5 kHz step only) max Audio Output : 2.6W nominal into 8 speaker 30mW nominal into 32 stereo headphone: Power Requirements : DC 1 1.
131 Remote Interface Jack 4pin Mini T ype GPS / Remote Interface Jack D-sub 9pin Male T ype Ext. DC Power / ORNG Wire Jack 3pin (Center Orange Wire) Operating T emperature : Nominal -20°C to +60°C Close Call -10°C to +60°C Size : 7.2 in. (W) x 5.9 in.
132 Reference Preset Fleet Map s Note: Size Codes in parenthesis indicates that the Size Code sp ans more than one block..
133.
134 User Defined Fleet Map s T ype I Programming Information When a T ype I system is designed, the address information for all the ID’s is divided into 8 equal sized blocks, numbered 0–7. When you program your scanner to track a T ype I system, you must select a size code for each of these blocks.
135 seems. Select a size code for a block, and then press . Now listen to the communications. If you decide you are receiving most of the replies to the conversations with ID’s assigned to the block you just programmed, then you’ve probably selected the right size code and can work on the next block of the map.
136 This page is intentionally blank..
137 This page is intentionally blank..
138.
139 This page is intentionally blank..
140 Index A B C D E Alert ..... .............. ,,,,,, , ,,, , ,,,, , , ,,, .. .............. ,,,,,, ,,, ......... ,,,,,, ,,, ......... ,,,, , , , Backlight ............. , , , .... .............. , , , , , , .... .............. , , , . .............. .
,,,,,,, ,,,, , , , ............. .......... , FCC ...... .............. ........... .... .............. ,,,, , .... .............. ,,,,,,, ,,,, , , ,, GPS ..... .............. ,,,,,,, ,,,,,,, , , ,,, , .. .............. ,,,,,,, ,,,,,,, ,,,,, Hits ....
R S T U V Record ,,,,,, ,, ....... , , , , , , , . . ,,,,,, ,,, .. ......... , ,,,,,, ,,,,,,, ,, ... .............. ,,,,,,, ,,, .... ,,,,,,, ,,,,,,, ,,,,,,, , ,,,, ,, , , , ,,,,, ...... ,,,,,,, , , ,,, , ,,, ,, , , . ,,,, , .......... ,,,,,,, , , ,,, .
143 This page is intentionally blank..
One-Y ear Limited W arranty UNIDEN UBCD996T Scanning Receiver IMPORT ANT : W ARRANTOR: W arranty only available in original country of purchase. ELEMENT OF W ARRANTY : W ARRANTY DURA TION: P ARTS COVERED: ST A TEMENT OF REMEDY : PROCEDURE FOR OBT AINING PERFORMANCE OR W ARRANTY : Evidence of the original purchase is required for warranty service.
145 This page is intentionally blank..
146 MEMO.
147 MEMO.
©2007 Uniden Australia Pty Limited, Uniden New Zealand Limited. Printed in China. UBZZ01335AA(0).
Een belangrijk punt na aankoop van elk apparaat Uniden UBCD996T (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Uniden UBCD996T heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Uniden UBCD996T vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Uniden UBCD996T leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Uniden UBCD996T krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Uniden UBCD996T bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Uniden UBCD996T kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Uniden UBCD996T . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
